DIY: Groundwire Kit
134 posts · 98,282 views · page 2 of 3
Replies continued
OK,I got mine in,so do I need to remove some screws to install these wires,or are all the holes you used already empty.
Ohya,and the sheet of paper manual says to ground the headlights,whats up with that.
eco the area I mounted are areas which already have screws in place. Just remove them and put them back with the ground wire in place. The only place that does not have a screw in place is the location I chose on the transmission.
You can ground the headlights also as we discussed in another thread, I just chose not too. It doesn't matter if you do or if you don't. And remember you don't have to ground to every single place I did, you can choose to ground whatever you want.
You can ground the headlights also as we discussed in another thread, I just chose not too. It doesn't matter if you do or if you don't. And remember you don't have to ground to every single place I did, you can choose to ground whatever you want.
so, I going to do a DIY ground kit... I was just going to buy some bulk 4 or 6 gauge car stereo wire in blue to match my theme, and all gold terminals. How much, do you supose should I buy of the bulk wire? I planned on using a gold junction block terminal, normally used for car stereo power wire. anyone have any better sugestions, or comments... Oh yeah there will be pictures for the whole thing...
what about this type of mod? anyone know about these?
If I'm right it basically hooks up to both the positive and negative terminals of the battery to better regulate and stabilize power. Not sure if it'll add increased performence, but might make electronics work better. Honestly it's considered by almost everyone in the automotive field as a bling item and nothing more. Never now though. If it's cheap then try it and let us now. 😉Originally Posted by SDsurfriderwhat about this type of mod? anyone know about these?
Im getting one,good price to.
let us know how it works. 👍Originally Posted by ecoIm getting one,good price to.
Will do,might be about 7 days before I install.
I was hoping to do another mod this weekend and write up a DIY, but it looks like I may have to wait until next weekend aswell.Originally Posted by ecoWill do,might be about 7 days before I install.
We are looking forward to your comments!
I'm having a tough time with mine x__x
I can't find anything grippy enough to hold that cylinder thing so I can stick the screw up it.. It seems to toughen out 3/4 of the way there and I just don't know what to use to hold it down :|
What'd you guys do?
I can't find anything grippy enough to hold that cylinder thing so I can stick the screw up it.. It seems to toughen out 3/4 of the way there and I just don't know what to use to hold it down :|
What'd you guys do?
You need to take a small flat head and clean out the grooves.
i believe there is a difference between stereo wire & power wire... i could be wrong, but im pretty sure i was told that by an electrical engineer once...Originally Posted by Black Yarisso, I going to do a DIY ground kit... I was just going to buy some bulk 4 or 6 gauge car stereo wire in blue to match my theme, .
not sure if it makes a diff on this or not...
No difference really as long as it's power/ground wire.
There are differences between audio/speaker wire and power wire.
Most power wires are aluminum, alloy or silver speaker wires are usually copper.
I have bulk spools of actual 8 gauge ground wire, The only difference really is the ground wire is braided for strength and not covered. the 8Awg is round twisted and appears to be aluminum, the standard 8 gaauge if flat braided wire also appears to be aliminum.
There are differences between audio/speaker wire and power wire.
Most power wires are aluminum, alloy or silver speaker wires are usually copper.
I have bulk spools of actual 8 gauge ground wire, The only difference really is the ground wire is braided for strength and not covered. the 8Awg is round twisted and appears to be aluminum, the standard 8 gaauge if flat braided wire also appears to be aliminum.
Good to hear. Hope you guys get yours soon.Originally Posted by bigsky2Those of you who bought from eBay seller 'racingguys' will be pleased to know that their UPS account is now active again.
My shipment left California yesterday.
I ordered from them about 2 weeks ago,got it last week,still need to install it,I aslo ordered a voltage stabilizer,like $75.00.
let me know if the adapter oart of the ground wire kit works with the tanabe strut bar. It looks like the strut may be blocking the location because it sits pretty low and close to the battery. It's the only thing holding me back from getting one.Originally Posted by ecoI ordered from them about 2 weeks ago,got it last week,still need to install it,I aslo ordered a voltage stabilizer,like $75.00.
have you guys noted a performance change? is it worth?
Itsmydaily,Ill let you know,it looks like it will be tight,but Im waiting for the voltage stabilizer now,so i can do them both at once,Ill tell you in about 3 days.
Voltage stabilizers are a bit overkill but can help when compnents drawing gobs of raw power off the battery are used. All cars have voltage regulators built in the alternator and most have secondary regulators under the dash for ECU and fuse pannel power...Originally Posted by Yaris-TJhave you guys noted a performance change? is it worth?
grounding kits don't hurt at all but they do very little.
IMO people that install grounding kits and can emidiatly fell a boost in HP are completly full of it !
On older cars they tend to help more when corroded grounds and rusted pannels are present but with a new car or even a couple years old, Any gains are very VERY small.
Also many grounding kit connections are pretty much useless and people tend to take them over the top. Like grounding the valve cover.... Keep it simple. Every ground does not need to run directly to the battery. Ground can be run in series. 4 connections to the battery is all you need. One to the fire wall, one to each strut tower or inner chassis. from these points you run you other grounds in series.
The most efficient grounding kit runs large, clean grounds to factory ground points like places where the OEM harness ground connect to the chassis, isolated throttle body or places that have large gasket areas with few fasteners or where corrosion can come between contacts such as alternator brakckets etc.
Grounding the valve cover, head, and block as well as other components on the engine is not needed. The head and valve cover are well grounded with MANY fasteners.
Anything larger then 8awg wire is overkill. Factory uses 12 or 10 AWG in most cases.
I've been making, installing and selling ground kits for years for Bikes ATV and car, and out of the hundreds I have sold and installed I have never felt any seat of the pants gains like most people that install them do. LOL
Picture lost · img.photobucket.com
The two grounds on the automatic Yaris are
#1 8awg from battery to left strut tower
#2 8awg from abttery to transmission
Wires that should be added
ground from battery to firewall (next to ECU/TCU)
ground from battery to right strut tower
From these points you can add grounds to
alternator bracket/AC unit
exhaust
throttle body
cylinder head
There is no need to add a ground to the transmission or left strut unless the Stock wires are removed. There is no need to ground the coild because they do not ground to the valve cover.
Also there really is no need to remove bolts and nuts to install a grounding kit on the yaris.
Removing bolts like the valve cover, manifolds, engine covers and throttle body etc can lead to oil leaks and air leaks not to mention over torquing them can strip holes/bolts, create stress cracks and break the cheap cast parts. The best method is to use existing bolts and holes available and in most cases a nother nut can be added to an existing bolt with threads to spare.
For instance
Alternator bracket has a pre drilled/tapped hole
Throttle body bolts can have a second nut added or use the waterpipe bracket bolt
lower ECU bolt can have a second nut added
firewall has unused studs
right strut tower has pre-drilled /tapped holes
Even the valve cover ground if you want to add one just pop off the cover, slip the ground over the plastic cover stud and put it back together.
This way the dealerships can't give you a hard time for removeing bolts and nuts to install anything.
The wiring kit like the one I made on my Yaris has all the ground in the kit coming from a central location on the firewall. I kept the OEM grounds on the Left strut tower and trans,
Battery to firewall stud. All wiring is using 8 awg copper high power and gold ring terminals.
Firewall to cylinder head
Firewall to exhaust
Firewall to throttle body
Firewall to right strut tower
Right strut tower to alternator bracket
Alternator brackt to AC compressor
I was wondering about that. I don't want to sound like an idiot but I don't see how it can increase your hp. Would you just get a better spark?
On a new car it won't do much if anything.
However better grounding can allow engine sensors to work more efficeintly becaise of equalized resistance.
Overtime ground points and connections can become corroded and rusted and poor ground can result in higher and lower resistance, poor ignition or false/poor sensor readings.
I have seen cars like my own Laser that did have several rusted and corroded connections after 10~15 years of driving. Components like the throttle body bolts and studs were really corroded badly and add to that a gasket between that and the head there is a possibility for a very poor ground. And adding a ground kit as well as cleaning up the original equipment grounds will help restore proper grounding and lost power. In my case I went through 3 alternators in a couple months and finally talked to a Mitsu mechanic for a rally team and he told me to clean up the OE grounds and add a few more to or close to the most important components to equilize the resistance. I did that and never had any more chrarging problems and a better steady idle. But that's it on a 12+ year old car, driven daily with 300,000k.
With gold terminals you don't have as much or any corrosion so over time you maintain the same performance.
I've heard almost every possible "felt difference" from other members from other boards about adding a grounding kit.
things like
faster 1/4 mile
Lower rpms at cruise speeds
Faster warm ups
Better throttle responce
Quieter engine
Fact is 99% of so called felt gains are bullshit. People get it in their heads it's going to help increase power and will swear it did. a basic Placebo...
Companies will tell you what you want to hear to sell you a product but for the most part these kits don't do any of these.
However better grounding can allow engine sensors to work more efficeintly becaise of equalized resistance.
Overtime ground points and connections can become corroded and rusted and poor ground can result in higher and lower resistance, poor ignition or false/poor sensor readings.
I have seen cars like my own Laser that did have several rusted and corroded connections after 10~15 years of driving. Components like the throttle body bolts and studs were really corroded badly and add to that a gasket between that and the head there is a possibility for a very poor ground. And adding a ground kit as well as cleaning up the original equipment grounds will help restore proper grounding and lost power. In my case I went through 3 alternators in a couple months and finally talked to a Mitsu mechanic for a rally team and he told me to clean up the OE grounds and add a few more to or close to the most important components to equilize the resistance. I did that and never had any more chrarging problems and a better steady idle. But that's it on a 12+ year old car, driven daily with 300,000k.
With gold terminals you don't have as much or any corrosion so over time you maintain the same performance.
I've heard almost every possible "felt difference" from other members from other boards about adding a grounding kit.
things like
faster 1/4 mile
Lower rpms at cruise speeds
Faster warm ups
Better throttle responce
Quieter engine
Fact is 99% of so called felt gains are bullshit. People get it in their heads it's going to help increase power and will swear it did. a basic Placebo...
Companies will tell you what you want to hear to sell you a product but for the most part these kits don't do any of these.
Originally Posted by bigsky2Ground wires are not meant to increase HP imho.
It's another marketing point for ground wire/voltage stabilizer manufacturers when they sell these types of products.
My goal is to strengthen the ground connections of the vehicle to reduce fluctuations in voltage, and hopefully reduce this sort of fluctuation on electronic components.
well said👍
Hey itsmydaily,everything fits fine with the Tanabe strut bar installed,just make sure they dont toch,i got some sparks,but thats because I installed the kit after the bar,alot harder.I only have the alternator and the intake hooled up at the moment,I also have my voltage stabalizer installed,I deffinitly notice the car is smoother,and when I start the car,it starts quicker,and the starter sounds stronger.
Guys do I need to buy a complete kit, like the one the guys above bought from ebay?
I have a custom one, but there are only 6 grounding points.
I have a custom one, but there are only 6 grounding points.
You ground what u wanna ground.
I made mine. Easy as crap.
thankx, thats good to know. looks like I'll be getting the strut bar then 🙂Originally Posted by ecoHey itsmydaily,everything fits fine with the Tanabe strut bar installed,just make sure they dont toch,i got some sparks,but thats because I installed the kit after the bar,alot harder.I only have the alternator and the intake hooled up at the moment,I also have my voltage stabalizer installed,I deffinitly notice the car is smoother,and when I start the car,it starts quicker,and the starter sounds stronger.
Got any pics? I'm curious to see where you mounted the voltage stabilizer.
Ok,Ill take some pics today.But if your curious and cant wait,I mouted it between my battery and fuse box.
My curiosity on this grounding kit
http://cgi.ebay.com.au/New-JDM-Groun...QQcmdZViewItem
hmmmmm should i? its just looooooksss soooo pretttyyyy......
http://cgi.ebay.com.au/New-JDM-Groun...QQcmdZViewItem
hmmmmm should i? its just looooooksss soooo pretttyyyy......
For $85....I'd pass.
wow never seen one like that before, good find, but not worth the price.Originally Posted by hasher22My curiosity on this grounding kit
http://cgi.ebay.com.au/New-JDM-Groun...QQcmdZViewItem
hmmmmm should i? its just looooooksss soooo pretttyyyy......
It looks like that stabilizes voltage aswell,but I think youll have a very hard time mounting that,you may,but you will not be able to see that voltage meter.Ill post the pictures of my partial install tomorrow morning.
Originally Posted by hasher22You ground what u wanna ground.
Yes but do I need more grounding points?
You don't need to have more. six is enough and even five would be enough. Only put more if you want to add more grounding points. Otherwise six is plenty.Originally Posted by KatanaYes but do I need more grounding points?
I believe there are 6 main points to ground. Though from what i heard/seen u can have 13 grounding points......correct me if im wrong...
Well here are the results from my grounding kit:
W/O GROUNDING KIT
---------------------OHMS----VOLTS
Alternator----------- 0.6-------0.02
ECU-------------------1.7-------0.005
Throttle Body------- 1.2-------0.011
Transmission-------- 0.6-------0.016
Head------------------0.7-------0.016
WITH GROUNDING KIT
---------------------OHMS-----VOLTS
Alternator------------0.6--------0.011
ECU-------------------0.6--------0.008
Throttle Body-------0.3--------0.001
Transmission--------0.1--------0.009
Head------------------0.5--------0.009
The Ohms were read while the engine was off, volts while engine was on. The readings were taken using a Fluke 87 Ohmmeter. The leads were placed, red on the bolt being tested, black on the negative terminal on the battery. The volts were a good indicator of how the resistance was reduced, since the more voltage flowing through the grounding wire, the less voltage drop across the voltmeter. If you wish, I can tell you exactly which bolts I used for my hookups/readings.
I will tell you this, I can detect a small difference in the pull of my engine at higher speeds. It feels a little more willing at higher RPMs. Nothing major though. Idle doesn't really feel any smoother. I'll let you know about any MPG changes, if there are any.
W/O GROUNDING KIT
---------------------OHMS----VOLTS
Alternator----------- 0.6-------0.02
ECU-------------------1.7-------0.005
Throttle Body------- 1.2-------0.011
Transmission-------- 0.6-------0.016
Head------------------0.7-------0.016
WITH GROUNDING KIT
---------------------OHMS-----VOLTS
Alternator------------0.6--------0.011
ECU-------------------0.6--------0.008
Throttle Body-------0.3--------0.001
Transmission--------0.1--------0.009
Head------------------0.5--------0.009
The Ohms were read while the engine was off, volts while engine was on. The readings were taken using a Fluke 87 Ohmmeter. The leads were placed, red on the bolt being tested, black on the negative terminal on the battery. The volts were a good indicator of how the resistance was reduced, since the more voltage flowing through the grounding wire, the less voltage drop across the voltmeter. If you wish, I can tell you exactly which bolts I used for my hookups/readings.
I will tell you this, I can detect a small difference in the pull of my engine at higher speeds. It feels a little more willing at higher RPMs. Nothing major though. Idle doesn't really feel any smoother. I'll let you know about any MPG changes, if there are any.
i think we need a new thread
I agree.
Has anybody bought a grounding kit yet and not installed it? Also are you willing to take pics?
Has anybody bought a grounding kit yet and not installed it? Also are you willing to take pics?
I can take pics of my installation, so the locations will be clearer.
nsmitchell interesting results. I think I will get some reading on my points over the coming weekend. I'd like to see what you decided to ground with your install.
Sorry,Ive been busy,Ill try to post pics tonight.
Well I feel like a special ed student...
if anyones wondering on how to install a Bought Grounding Kit then go back to the first page and to post 1 of this thread....
I think what still needs to be made is the DIY Guide for making and installing your own homegrown grounding kit.
if anyones wondering on how to install a Bought Grounding Kit then go back to the first page and to post 1 of this thread....
I think what still needs to be made is the DIY Guide for making and installing your own homegrown grounding kit.
Originally Posted by ItsMyDailyYou don't need to have more. six is enough and even five would be enough. Only put more if you want to add more grounding points. Otherwise six is plenty.
Thanks, you saved me 30 euros.
Guys is anyone interested in a DIY Grounding Kit for the 1.3lt engine?If yes I can fix you up!
Has anyone measured the length of the wires in the e-bay kit?
The average person can't make a kit for $22 when you factor in the cost of quality wire at $1 + per foot and quality ring connectores at $1 a piece or more.
The average person can't make a kit for $22 when you factor in the cost of quality wire at $1 + per foot and quality ring connectores at $1 a piece or more.
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
Picture lost · i109.photobucket.com
That one wire with brown tape is actually going onto the ECU,I just havnt found a screw that fits that open hole,theres 2 holes open on the ECU,so I figured Id just let it sit on the intake manifold for a few days.I have 4 points so far,Intake,alternator,left and right side of the engine block,next will be transmission,then the throttle body,and maybe more,Ill think of something.
^ looks great. Wow the strut bar just barelly clears it, man thats tight. Great location for the stabilizer aswell.