Yarisworld Archive

Cambered Hub Spacer's , Interested yes / no

41 posts · 13,705 views

1NZYaris1Original postNew Zealand · Jun 27, 2009#1
Hi Guy's and Girls
If these where on offer , would you be interested , would you purchase
The following fiquires are worked out from a 24" wheel size
Official YARIS Wheel & Tire Guide

The fiqures below show the wheel movement (offset) at the
top - and bottom + of the wheel, Relivant to the hub camber angle.

Proposal is this 12.5mm thick spacer's with possably the following cambers
--------------------Bottom -------Top

0.5 deg camber +2.66mm -2.66mm
1.0 deg camber +5.32mm -5.32mm
1.5 deg camber +7.98mm -7.98mm
2.0 deg camber +10.64mm -10.64mm
2.5 deg camber +13.30mm -13.30mm

This is an interest only thread , and if there is enough interest , they
will be put into production , and sold by a Regestered Vendor.

2 attachments not included in this copy

Replies 40

TamagoOff Grid · Jun 27, 2009#2
sounds familiar. looks familiar. the first pic looks like something i sold in the past. and i think you mean 12.7mm lmfao

Picture not included in this copy
1NZYaris1Thread starterNew Zealand · Jun 27, 2009#3
Made those 6 weeks ago , kiwi's can do any thing .😁

And no the material is 12.5mm Marine alloy
also made some 10mm ones
TamagoOff Grid · Jun 27, 2009#4
Originally Posted by 1NZYaris1 ↑
Made those 6 weeks ago , kiwi's can KNOCK OFF any thing .😁

And no the material is 12.5mm Marine alloy
also made some 10mm ones
good for you buddy
Nexus1155Dorchester · Jun 27, 2009#5
I voted it a good idea but no thanks since that was his previous design of the spacers that he made, but has a new revised one now. Maybe if you buy his new set and try that design instead?
TamagoOff Grid · Jun 27, 2009#6
my question to the OP is.. are you going to take out the dangerous toe in/out issues associated with camber +spacer setups?
1NZYaris1Thread starterNew Zealand · Jun 27, 2009#7
Originally Posted by Nexus1155 ↑
I voted it a good idea but no thanks since that was his previous design of the spacers that he made, but has a new revised one now. Maybe if you buy his new set and try that design instead?
This design is a direct copy of the hub , Tamago's design is muti fit
Yaris , and Xa , Xb i beleave , of which i donot have one to test fit ,
and develope .
TamagoOff Grid · Jun 27, 2009#8
Originally Posted by 1NZYaris1 ↑
This design is a direct copy of the hub , Tamago's design is muti fit
Yaris , and Xa , Xb i beleave , of which i donot have one to test fit ,
and develope .
i'd love to see these fit on an xB and xA 😆
1NZYaris1Thread starterNew Zealand · Jun 27, 2009#9
Originally Posted by Tamago ↑
my question to the OP is.. are you going to take out the dangerous toe in/out issues associated with camber +spacer setups?
🤷 and you are, have?.
but yes that can be done as well , if there is enough interest
TamagoOff Grid · Jun 27, 2009#10
Originally Posted by 1NZYaris1 ↑
🤷 and you are, have?.
but yes that can be done as well , if there is enough interest
xA/B is completely different. this is why the Yaris spacers are unique. and apparently now knocked-off by you (the main reason i went back into production)
1NZYaris1Thread starterNew Zealand · Jun 27, 2009#11
Originally Posted by Tamago ↑
xA/B is completely different. this is why the Yaris spacers are unique. and apparently now knocked-off by you (the main reason i went back into production)
Yes me bad , should have put Scion xD instead of xA/B, sorry.
AS Stated above this is a feeler thread , not a for sale thread

But as far as knocking of your design, i pm you for your help 8 weeks ago and you told me too piss off , so i have made my own ,by copying my hub and nothing else.
And as for knocking off your design how is that different to you knocking
of the inner guard brace's Garm is selling.🤮
TamagoOff Grid · Jun 27, 2009#12
Originally Posted by 1NZYaris1 ↑
And as for knocking off your design how is that different to you knocking
of the inner guard brace's Garm is selling.🤮
huh? i have no idea what you're talking about.


i did not tell you to piss off. want me to post the PM's ?
06silveryarisPuerto Rico · Jun 27, 2009#13
You can easily make camber adjustmens in the rear by using chims or washers instead of changing hubs if you want to keep the factory offset
TamagoOff Grid · Jun 27, 2009#14
Originally Posted by 06silveryaris ↑
You can easily make camber adjustmens in the rear by using chims or washers instead of changing hubs if you want to keep the factory offset
yup

Link to a thread or page that is not in the archive

and those who have a bench grinder can obviously DIY this (but seriously, who wants to grind washers by hand?)
06silveryarisPuerto Rico · Jun 27, 2009#15
Well it is time consuming but with thin washer just go adding as needed till your desired degree is reached.
TamagoOff Grid · Jun 27, 2009#16
Originally Posted by 06silveryaris ↑
Well it is time consuming but with thin washer just go adding as needed till your desired degree is reached.
absolutely.
1NZYaris1Thread starterNew Zealand · Jun 27, 2009#17
Originally Posted by 06silveryaris ↑
Well it is time consuming but with thin washer just go adding as needed till your desired degree is reached.
yep it probably is ,and this is just another possability, too save on that .
thank you for your comments.
cali yarisCanoga Park, CA · Jun 28, 2009#18
The hub spacer itself is not a new invention. Surely Tamago got the idea of using hub spacers from some previous version that someone else made (for another car, obviously). No one criticized him for adapting them (copying the invention, in a sense) for the Yaris, and it wouldn't be right to do so.

These hub spacers seem to have a unique feature (built-in camber). Whether or not you like the idea, it is original and different than Tamago's approach using washers.

So back to the point of the thread - do you like the idea?
1NZYaris1Thread starterNew Zealand · Jun 28, 2009#19
🙇 🙇 🙇 🙇 👍
1NZYaris1Thread starterNew Zealand · Jun 29, 2009#20
🍻
TamagoOff Grid · Jun 29, 2009#21
Originally Posted by 1NZYaris1 ↑
🍻

Picture not included in this copy
cali yarisCanoga Park, CA · Jun 29, 2009#22
That is a very funny face.
1NZYaris1Thread starterNew Zealand · Jun 29, 2009#23
Hey Tamago you could always do this with your's ,
more than happy too share the info (spec's) on angles and dimension's 👍

Oh and the above pic , is that a self portrait, looks pretty cool 😁

have a nice day 👍
BrazdonWColumbia, MD · Jun 29, 2009#24
I like the idea 👍
I'd buy a pair off of you if the price is reasonable
1NZYaris1Thread starterNew Zealand · Jun 29, 2009#25
That's the whole idea of this thread 👍 guage interest and if enough
put into production with penguin garage , Tamago , or my self.
contraband831CEN*CAL · Jun 30, 2009#26
great idea, I have seen some of these on one of the scion forum, hopefully there is enough interest.
1NZYaris1Thread starterNew Zealand · Jun 30, 2009#27
at this point , it appear's not . 🙄
TamagoOff Grid · Jun 30, 2009#28
Originally Posted by contraband831 ↑
great idea, I have seen some of these on one of the scion forum, hopefully there is enough interest.
if it's not for the xD then it won't fit the yaris. yaris = xd in many ways.
1NZYaris1Thread starterNew Zealand · Jul 3, 2009#29
looking to do a small sample run ,within in the next 5 day's , those of you interested , please speak up . 👍

Edit the offset is 12.5mm with a 1.5 camber
1NZYaris1Thread starterNew Zealand · Jul 4, 2009#30
any one else , and yes you can PM me to stay Anonomyous 😆

if you want a smaller camber you will need too ask , as these will be made
at the same time if required .
PETERPOOPOahu · Jul 4, 2009#31
GL with this. hope it gets going!
1NZYaris1Thread starterNew Zealand · Jul 4, 2009#32
Originally Posted by PETERPOOP ↑
GL with this. hope it gets going!
Thanks Peter 👍
1NZYaris1Thread starterNew Zealand · Jul 6, 2009#33
Last chance .
MUSKOKA800Chatham, Ontario, Canada · Jul 10, 2009#34
I might be interested however at this point I have absolutely no idea what degree of negitive camber I'd want/need for street use. A trial and error process may be necessary to determine the best compromise.
TamagoOff Grid · Jul 10, 2009#35
street needs would be a few washers and that's it ;)
1NZYaris1Thread starterNew Zealand · Jul 11, 2009#36
Originally Posted by Tamago ↑
street needs would be a few washers and that's it ;)

Or you could just buy your hub spacers with , camber already done for $95.00 shipped 👍
anonymous userwindward oahu · Jul 12, 2009#37
I was running negative four degrees camber on my fronts, so why only the mild options?
1NZYaris1Thread starterNew Zealand · Jul 12, 2009#38
Originally Posted by anonymous user ↑
I was running negative four degrees camber on my fronts, so why only the mild options?
very simply because there is no demand , and the set up cost's ,
would be more than what anyone would pay for them.
But if you really want 4 degrees , i would be more than happy to
make a set for you .
MUSKOKA800Chatham, Ontario, Canada · Jul 12, 2009#39
Offhand, can anyone advise the factory rear camber setting for an '08 sedan?
1NZYaris1Thread starterNew Zealand · Jul 12, 2009#40
Originally Posted by MUSKOKA800 ↑
Offhand, can anyone advise the factory rear camber setting for an '08 sedan?
yep factory camber is set just under 1.degrees (0.97 +- 0.75)
if you want you can check it yourself by looking it up in the
Link to a thread or page that is not in the archive

look under the Suspension PDF 👍
Penguin GarageFL · Jul 12, 2009#41
The reason we didn't do the camber added spacers was this exact reason. Far too many options which would increase the overall cost/retail price of the product. Since a shim/washer can achieve most camber settings.

be glad to help if i can.