Hi guys i just bought a new set of projector headlights.....they look great but dont give out enough light for night driving. Has anyone gone through this and can it be fixed?
Halo Projector lights
29 posts · 8,155 views
Replies 28
got any pics?
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
It was dark i just took em now
Picture not included in this copy
Picture not included in this copy
It was dark i just took em now
3 attachments not included in this copy
that one look flush on the car. it fits perfect...
i hope you're not using just the halos for driving and actually have hid bulbs in there...
you have to upgrade to HID, don't bother with the OSram Silverstars it doesn't make enough of a difference. do a search there are threads on here as to which kit to buy. but you will lose your hi beams for most which is only a problem if you have to pass inspection(which I do) anybody figure that out short of a custom harness?
the halos and the high beam works perfectly, the low beam lights are the ones that arent bright enough. I can only see about 10 to 15 feet at nignt on low beam. And it is written on the back do not use hid bulbs im confused.Originally Posted by haku ↑i hope you're not using just the halos for driving and actually have hid bulbs in there...
Thanks mate did it all by myself and instructions from DIY threadOriginally Posted by marcus ↑that one look flush on the car. it fits perfect...
you might need to aim it correctly. looking at the driver side, the projector on the right is for hids and the one on the left is for regular bulbs. i think the warning's just for the regular side since projector headlights are made for hids.Originally Posted by elijahsami ↑the halos and the high beam works perfectly, the low beam lights are the ones that arent bright enough. I can only see about 10 to 15 feet at nignt on low beam. And it is written on the back do not use hid bulbs im confused.
Not really, there are halogen projectors and HID projectors. They might look the same from the outside. But the internals have their slight differences. Placing HID bulbs in a projector designed for halogens will cause more glare than a projector that's designed for HID bulbs exclusively.Originally Posted by haku ↑.. since projector headlights are made for hids.
But having said that, HID bulbs in any projector would still be alot better than HID's in a halogen reflector bowl.
Thanks guys, that was very helpfull👍 I have to now take out the lights so i can get brighter bulbs most probably the 30%Xenon halogen bluish white ones. One quick question how do i adjust the aiming of the projectors? Do i have to get special tools or unlock anything before i turn the adjusters?
dont get the blue bulb light theyre crappier than the stock one..get hids.
umm u shouldnt get new bulbs....
those lights that came with the headlights should do just fine. When i installed mine, it was wayyyy better than stocked. Prob 30% Brighter and clearer.
Sure u connected it properly? Take pics with the lights on?
those lights that came with the headlights should do just fine. When i installed mine, it was wayyyy better than stocked. Prob 30% Brighter and clearer.
Sure u connected it properly? Take pics with the lights on?
it looks better in the photos dont know why
3 attachments not included in this copy
Nice Speedo 🙂Originally Posted by elijahsami ↑it looks better in the photos dont know why
Your lights appear to be aimed too close.. more so the passenger side one. Look where the cut-off is for that side compared to the driver side..
its stock lol😳Originally Posted by KoDoK NyeLeM ↑Nice Speedo 🙂
So i just have to adjust the aiming and not replace bulbs? So i aim the passenger side a bit higher or the driver side lower? Sorry to ask so many question im new to the DIY stuff just dont wana do something wrong to my baby😳
yeah they look aimed far too low! I had the opposite problem with mine, my cutoff was too high.
If you take out the headlights again, look at the back, there should be 2 screws that you can use the adjust the aim. You'd need to screw each one in equally, 1 full turn should be enough. It's a bit of a pain but not too bad...
If you take out the headlights again, look at the back, there should be 2 screws that you can use the adjust the aim. You'd need to screw each one in equally, 1 full turn should be enough. It's a bit of a pain but not too bad...
Park your car on a level surface against a wall, about 3m away. Then adjust the passenger side UP until it's level with your driver side beam. When both side's cut-off line up then it is level. You might be able to adjust them without taking the light out again, I'm not sure how these lights look on the rear.
I adjusted my lights and they give amazing coverage...and it took only one minute or less thanks so much for the information guys......🙇🤘 And the best thing was i didnt have to take my lights off as suggested by some members in other threads.......thank you all for helping cheers👍
Can I get these projectors for a Sedan Yaris....I've searched everywhere but the only one I found are for the 3drs....????
after photos pls..
I would probably do HID's even if it says not to on the low beams. You can then adjust them not to blind oncoming traffic. The only risk is that the housing cannot handle the increased heat, but I personally would take that chance.
aint the hid running cooler that regular bulb since its 35 watts rather than 55 watts.Originally Posted by cali yaris ↑I would probably do HID's even if it says not to on the low beams. You can then adjust them not to blind oncoming traffic. The only risk is that the housing cannot handle the increased heat, but I personally would take that chance.
Before....low beamOriginally Posted by marcus ↑after photos pls..
Picture not included in this copy
After
Picture not included in this copy
High beam
Picture not included in this copy
Picture not included in this copy
4 attachments not included in this copy
I was gonna do that and i also was gonna buy the heavy duty harness from you thats untill some kind people suggested me to adjust my aiming at the moment im pleased with the light output but i will get hids after i do more mods. Thanks for the tip mateOriginally Posted by cali yaris ↑I would probably do HID's even if it says not to on the low beams. You can then adjust them not to blind oncoming traffic. The only risk is that the housing cannot handle the increased heat, but I personally would take that chance.
At the moment i havent found a seller but i am looking for a pair myself as i have both a sedan and a hatchback if i do find a seller i will tell all of yaOriginally Posted by dirtking180 ↑Can I get these projectors for a Sedan Yaris....I've searched everywhere but the only one I found are for the 3drs....????
how'd you know what he was wearing while taking the picture? amazing.Originally Posted by KoDoK NyeLeM ↑Nice Speedo 🙂