Yarisworld Archive

My Windshield Wipers died

36 posts · 34,190 views

ztrack157Original postBiggs, CA · Jun 5, 2009#1
I don't know what the heck is wrong. Either a Fuse (which I don't know which one or where it exactly is), The switch, or the motor. I can still use the switch for the rear wiper and the washer fluid front and back. Just the motor doesn't work. But how do I tell if it is bad or not? Or what my culprit is?

Replies 35

dvlnblkdrsorange, ca · Jun 5, 2009#2
fuse box has map on lid, but sounds like motor, if was fuse nothing would work i think....
ztrack157Thread starterBiggs, CA · Jun 5, 2009#3
eh that fuse map didn't help. I'm betting on the motor. Either way its $100 bucks.
dvlnblkdrsorange, ca · Jun 5, 2009#4
lol i had to find tonys correct fuse when he blew his interior lights.. lol and theres spares in the box... but yea, prolly motor... sux its so expensive tho
texkidSugar Land, TX · Jun 5, 2009#5
I would say check the fuse box first. Go from small problem to big.
ztrack157Thread starterBiggs, CA · Jun 5, 2009#6
I checked all the fuses and nothing
texkidSugar Land, TX · Jun 5, 2009#7
Originally Posted by ztrack157 ↑
I checked all the fuses and nothing
Hmmm....well. If you're still brave. Get a voltage tester, take off the front panel covering the wiper motor, turn the key, flip the wiper switch and see if a current is running. If it is, them motor is dead. If it isn't, then there is break in the current and figure out from there (maybe something wrong at the wiper switch end?).

The evil method would be to rent a Yaris, take it to your garage, switch the parts, and return the car. But you didn't hear that from me.

Added note: sorry for the long run-around. Its better to rule out step by step. Hate for you to run and buy a new motor when all you needed was a wiper switch or some other major part.
CTScottUSA, CT · Jun 5, 2009#8
I would think the switch is more likely the culprit than the motor. If the motor/gearbox failed mechanically it would keep taking out the fuse. The front wiper, rear wiper, and washers are on separate fuses (15A WSH {front and rear washers}, 25A WIP {front wiper}, 15A RR WIP {rear wiper}).

If the 25A WIP fuse is not blown, I would try bypassing the front wiper switch.

To do so, on the stalk connector, jump the +B to +1 wires. Black (pin 2) to Blue (pin 3) using a small stiff piece of wire.

Wiper Conn Detail.jpg
jambo101Montreal Canada · Jun 5, 2009#9
If you still have some warranty let the dealer deal with it.
Could also be a malfunctioning activation switch on the steering column ,you might want to find out before you blow money on the motor only to find out that it still doesnt work.Like texkid said
toyoJapan I wish · Jun 5, 2009#10
yaris spec?

I can look up in workshop data for the fuses diagram and send it to you, so you can change the exact one you need to change.

My interior lights didn't work, I tested all fuses and they all seemed ok. I looked it up in the program, found out wich one was the one for the interior, replaced it, and probem fixed :P there are a lot of fuse boxes and sometimes two fuses for each thing.
ztrack157Thread starterBiggs, CA · Jun 5, 2009#11
please do so toyo. because its like a needle in a hay stack unless your CTscott. And everything he said was greek to me.
ztrack157Thread starterBiggs, CA · Jun 5, 2009#12
I have a wire partially exposed going into the wiper motor. It is the yellow one on the connector. Theres some insulation missing but it is not all the way thorugh nor did it damage the copper wire.
ztrack157Thread starterBiggs, CA · Jun 5, 2009#13
Ok just tested the pins on the connector to the motor. I get juice from them I even went through the stage on intensity to make sure there was a variation as well. This means the motor is shot. Correct?
auxmikeLI, New Yawk · Jun 5, 2009#14
Are you out of warr. already??🤷
CTScottUSA, CT · Jun 5, 2009#15
The black wire will have 12 volts on it even when the wiper is off. Blue will read 12 volts when the switch is on low. Yellow will read 12 volts when the switch is on high. The white changes from ground to 12 volts when the wiper moves part of the way.

(Hopefully no Greek this time...)
ztrack157Thread starterBiggs, CA · Jun 5, 2009#16
CT what you described above is what I was getting
This would mean the motor is out correct.
CTScottUSA, CT · Jun 5, 2009#17
Originally Posted by ztrack157 ↑
CT what you described above is what I was getting
This would mean the motor is out correct.
I would say that is correct.

Just make sure that the white with a black stripe wire grounded well. If it is then I would definitely say that something has opened within the motor assembly. If it is not a solid ground, then it could be the issue, as it completes the circuit to allow the motor to run.
ztrack157Thread starterBiggs, CA · Jun 5, 2009#18
I ordered a new motor for cheap so we will find out in a week. If it doesn't work then I will need help with the grounding issue. But the tester shows green all the time on the ground so I'm good to go hopefully.
ztrack157Thread starterBiggs, CA · Jun 12, 2009#19
Ok guys the motor is not the issue. I need to know were the fuse is for this. Eliminating the possible problems one by one. LOL. It may be grounding or it maybe the switch itself. Either way I need some help.
CTScottUSA, CT · Jun 12, 2009#20
Originally Posted by ztrack157 ↑
Ok guys the motor is not the issue. I need to know were the fuse is for this. Eliminating the possible problems one by one. LOL. It may be grounding or it maybe the switch itself. Either way I need some help.
The fuse is under the bottom of the dash on the driver's side (look up from the floor and you'll see the cover with the labels). The fuse is #3, which is labeled as WIP and is a 25A fuse.

You mentioned before reading voltage on some of the pins on the wiper connector. This more than likely means that the fuse is not the issue. Can you take readings again and post the wire color and what the voltage reads on it (with the wiper switch off, then with the wiper switch in "high")?
ztrack157Thread starterBiggs, CA · Jun 19, 2009#21
Ok with the wipers off. I get 12 volts from the non ground pins. As soon as I hit the switch nada.
HavocMaryland · Jul 2, 2009#22
I just had this problem. Although it doesn't sound like the same cause as Ztrack's, here it is for the record. I had headers installed and they apparently took off the top cowl. I checked the fuse and all, then found this lonely connector just dangling in the wind behind the battery.

Picture lost · www.bwcorridor.com

It goes here after removing the wipers and cowl.
Picture lost · www.bwcorridor.com


EDIT: I had coilovers install at the same time. That might be why they disconnected it.
auxmikeLI, New Yawk · Jul 2, 2009#23
Wow, you already did this all on an '09?
TamagoOff Grid · Jul 2, 2009#24
n/m repost
ptitpiffuteMontréal · Dec 15, 2013#25
Hi Guys,

I've a similar issue but a bit weird. When it's cold, front wipers stop moving and when the car is getting warmer, sometimes they work. As soon as it is not freezing, it works fine.

Battery was changed today and not sure it changed something.

Can you help ? It sounds like corrosion somewhere ....

Thx
myfirstyotaToronto Canada · Feb 14, 2016#26
Originally Posted by ptitpiffute ↑
Hi Guys,

I've a similar issue but a bit weird. When it's cold, front wipers stop moving and when the car is getting warmer, sometimes they work. As soon as it is not freezing, it works fine...
Sorry for reviving an old thread but I've looked at all 120 something posts relating to wipers and this is the closest to my issue.

I've recently purchased a 2007 base model lb. With 120,000k on it now. My first Toyota.

As anyone in southern Ontario knows, its been a mild winter so far this year. 2 days ago I was on my way to work north of Toronto. As I went to exit the hiway I went for the windshield washers. They sprayed but the wipers were on strike. ( it was particularly cold that day) it kinda broke my heart, I've heard such good things about Toyota and yaris.

Later on after work, when it had warmed up at bit, they worked fine.

The next day, -20°c. Again they were on strike. The wipers wouldn't react at all to the switch. Like the car was off. After doing some interior wiring (CTScotts cruise control diy) with the car running for heat, the wipers were working flawlessly again.

The next day, -20°c again. Wipers = door nail = dead.

Now another 30 min of idling with the heat on for test purposes they're working great.

Clearly I'm leaning toward a temp. Issue. Any new findings anyone?

Thanks in advance

Owen
ex-x-fireSheboygan Falls, Wi. · Feb 14, 2016#27
Try tapping the wiper motor with a screwdriver handle to see if it reacts.
myfirstyotaToronto Canada · Feb 14, 2016#28
That was my first thought... The old shoty sarter motor trick. Then I looked at all the cowling/wiper cover, realized it was -20°, and said f-it lol. I don't have a garage either so that didn't help the cause lol.

Just wondering if anyone has had the problem. Motor issues? Moisture in the wiring? I do wash the car regularly to prevent salt buildup... But the wiper assembly doesn't appear to be frozen as when one wiper is wiggeled gently, the other reacts as expected.
CTScottUSA, CT · Feb 14, 2016#29
Originally Posted by myfirstyota ↑
That was my first thought... The old shoty sarter motor trick. Then I looked at all the cowling/wiper cover, realized it was -20°, and said f-it lol. I don't have a garage either so that didn't help the cause lol.

Just wondering if anyone has had the problem. Motor issues? Moisture in the wiring? I do wash the car regularly to prevent salt buildup... But the wiper assembly doesn't appear to be frozen as when one wiper is wiggeled gently, the other reacts as expected.
Next time it happens try just turning the ignition on and turning them on and listening by the cowl to hear any noise from the motor. Also try giving them some gentle help.

The relay for the wipers is located within the base of the wiper stalk, so it too could be not liking the cold.
myfirstyotaToronto Canada · Feb 15, 2016#30
Just went to get my morning Timmie's, tried the wipers, didn't go in the driveway. But worked when I got my tea. Just tried the fast setting and no go for a few seconds then they went. Every other speed worked fine.

Gotta love electrical lol.

CTScott, do you know of a test procedure for the signal stalk? What I mean is, can I take a multimeter and look for specific voltages at the stalk?

Thanks in advanve
CTScottUSA, CT · Feb 15, 2016#31
Originally Posted by myfirstyota ↑
Just went to get my morning Timmie's, tried the wipers, didn't go in the driveway. But worked when I got my tea. Just tried the fast setting and no go for a few seconds then they went. Every other speed worked fine.

Gotta love electrical lol.

CTScott, do you know of a test procedure for the signal stalk? What I mean is, can I take a multimeter and look for specific voltages at the stalk?

Thanks in advanve
On the larger wiper stalk connector:

Black: +12 constant power
White: Switched +12 coming back from the wiper's cam switch
Light Blue: Low speed output (+12 when wipers are in low)
Yellow: High speed output (+12 when wipers are in high)
myfirstyotaToronto Canada · Feb 16, 2016#32
Thanks Scott, however the test may have to wait. It has warmed up and isn't supposed to get too cold again for a while. The wipers have been working perfect since yesterday afternoon.

However this issue is bothering me and was considering removing the switch and putting it in the freezer for a bit hahahah.

You are an awesome being Scott.

Thank you so much.
ptitpiffuteMontréal · Mar 11, 2016#33
myfirstyota,

The issue I had was pretty much the same as what you described. After about 2 years of wipers working and not working, they ended up to stop.
So I checked the motor and it was dead, so changed it and since then, I never had any trouble again.

Just so you know O_-
myfirstyotaToronto Canada · Mar 13, 2016#34
Originally Posted by ptitpiffute ↑
myfirstyota,

The issue I had was pretty much the same as what you described. After about 2 years of wipers working and not working, they ended up to stop.
So I checked the motor and it was dead, so changed it and since then, I never had any trouble again.

Just so you know O_-
Did you ever have any trouble with them in the summer months?

Mine have been going almost perfectly since my last post with the exception of once. There was some hesitation and slow movement when I went for the high speed, but only momentarily. Then they were back up to high speed within 3-4 seconds.
ptitpiffuteMontréal · Mar 13, 2016#35
In summer, they were working again. That's why it took sometime to fix it. But at one point during winter, the motor finally died for good.

I checked if power was getting to the motor and all was good, so I decided to change it. Since it works like a charm.

Ordered mine from rockauto in the us.

I hope you'll find the problem, we've the same model of Yaris and live almost in the same weather region.
myfirstyotaToronto Canada · May 29, 2016#36
An update: after the wipers finally kicking the bucket for good, I decided to pull the motor and take a peek. Upon disconnecting the 5 wire harness clip from the motor assembly I noticed the harness side of the clip wasn't looking too fresh. The pin on the wiper motor side of the clip associated with the large black wire was completely corroded away. A trip to the bone yard yeilded a motor assembly complete with wire harness, from a very similar car with lower km. I decided to pull all the pins from the clip, clean them up, apply some dielectric grease, and swap in the cleaner clip I got with the used motor. I installed the new used motor with the newly rebuilt connector and everything seems to be working great.

So if anyone else is having this problem, check the connector to the wiper motor. There may be some corrosion inside the clip preventing a solid connection, or in my case a completely dissolved pin.