Yarisworld Archive

So this is bad, right?

34 posts · 8,908 views

naossoanOriginal postMB, Canada · May 30, 2009#1
So before I left for work this morning, I decided to check the tops of the shocks to make sure everything was still tight.

I installed the springs at a friends house with a garage 2 hours away and drove home on the highway afterward. I'm assuming they were probably like this the whole drive home.

Is this why the instructions said not to use the same nut from disassembling the shocks to put the new springs on? But I did anyways because I didn't have any other nuts to use...

Do I have to re-do the front end and tighten up that nut?

Picture lost · i88.photobucket.com
Picture lost · i88.photobucket.com

Replies 33

AlexNet0Rockland, ME · May 30, 2009#2
this gap has been present on all the aftermarket installs that I have seen on here.

I do not believe it matters, however wait before someone more knowledgeable on springs chimes in before you take my advice.
ddongbaphay · May 30, 2009#3
Damn yo, thats a pretty decent camera. I can't take closeup-anything with mine.
1NZYaris1New Zealand · May 30, 2009#4
Jack the car up , till the front wheels are off the ground ,
if the gap disappear's then yes you have a problem.
naossoanThread starterMB, Canada · May 30, 2009#5
Originally Posted by ddongbap ↑
Damn yo, thats a pretty decent camera. I can't take closeup-anything with mine.
Hey thanks.

It's a Canon SD1100IS 8 MP pocket/point and shoot camera. It was $199 when I bought it, it's a bit cheaper now I think. It's a pretty decent little camera, yep.

As for the gaps, anyone else have a suggestion?

Thanks!

EDIT: Ah I didn't see the above reply before I replied. I am at work but I will try that when I get home..I don't have a jack other than the one included with the car from Toyota. I can just lift up one side at a time, yea?
1NZYaris1New Zealand · May 30, 2009#6
Originally Posted by naossoan ↑
Hey thanks.

It's a Canon SD1100IS 8 MP pocket/point and shoot camera. It was $199 when I bought it, it's a bit cheaper now I think. It's a pretty decent little camera, yep.

As for the gaps, anyone else have a suggestion?

Thanks!

EDIT: Ah I didn't see the above reply before I replied. I am at work but I will try that when I get home..I don't have a jack other than the one included with the car from Toyota. I can just lift up one side at a time, yea?
just lifting up one side is Ok , 👍
Malaya1221Torrance, Ca · May 30, 2009#7
we had 2 old threads before the hack and i believe that all of us that lowered the car have that gap!
1NZYaris1New Zealand · May 30, 2009#8
No gap on mine 😁
TRD Suspension 008.JPG
Malaya1221Torrance, Ca · May 30, 2009#9
hmm...1nz, did u cut the bumpstops?
naossoanThread starterMB, Canada · May 30, 2009#10
OK that sounds reassuring. On the drive home everything *felt* normal. Handling was great too.

I'll try what 1NZYaris1 suggested, see if the gap is gone when i take the weight off the shock. I remember when I still had the car up on car jacks after I put the shocks in, there was no gap then. I can't recall if I saw it when I put the car on the ground while I was putting in all the stupid black air ducting crap as I wasn't really looking at the shock caps.

When I cut the bump stops, I did them according to what TEIN's instructions said, or at least how I interpreted them. IT said to cut them in manner "A" which was to remove some from the bottom, 1.4 inches. I wasn't sure if they meant the bump stop swere to be 1.4 inches total, or to cut 1.4 inches off. But I marked a line at 1.4 inches from the bottom and started hacking away. I read that it's important not to cut the bump stops too much or you will bottom out the chocks during sharp/fast corners or hitting large bumps at speed, so I figured it was safer to go with the 1.4 cut off...as it wasn't quite half of the whole bump stop.
Malaya1221Torrance, Ca · May 30, 2009#11
1nz, your pic here from ur garage has that gap...did u solve it? how?...btw, clean engine bay...🙂

AFE intake 001.JPG
CtrlAltDefeatIndianapolis IN · May 30, 2009#12
I've seen several lowered Yari with that gap, including mine...
1NZYaris1New Zealand · May 30, 2009#13
No that, photo is a little miss leading , that was taken on stock suspension
and the dimples where touching .👍

I will double check mine when it get's home next week, it's gone on
a road trip arround the South island.
CtrlAltDefeatIndianapolis IN · May 30, 2009#14
just took a picture of my dirty dirty engine bay 😁
top of shocks1.JPG
naossoanThread starterMB, Canada · May 30, 2009#15
Interesting, so maybe I didn't need to waste my energy biking to work this morning! LOL!

I need the exercise anyways.

Any idea why this happens? I don't really understand why the top would be pushed up like that.
CtrlAltDefeatIndianapolis IN · May 30, 2009#16
I don't know, but I bet when you hit a bump on stock springs it goes up like that. With the shorter springs, it's like there's a pre-load of sorts on the shocks. At least thats my guess...
detroiterMetro Detroit · May 30, 2009#17
I have a tiny bit, but hardly anything like the last picture up above. My gap is very minute. I'd say it's just the nature of the lowering beast.
PhaetonPort Angeles, Wa · May 31, 2009#18
same here. I think it goes with lowering the car.
naossoanThread starterMB, Canada · May 31, 2009#19
ok i wont worry about it so much.

Thanks.
TreyzLong Island, NY · Jul 2, 2009#20
OK so I installed my old TRD's Sportivos and TRD Springs on my new 09. I have the same problem and I'm not liking it at all.

I read on here that with the TRD setup, the bumpstops aren't needed to be cut. As a result of this, I have now aquired "the gap" ...






My last yaris I had cut the bumpstops because I had the Tanabe DF210's and then switched to the TRD's. All was flush when I swithced the springs.

In all honesty, I really don't feel save knowing that there is a little gap/play if for some reasonone of the fronts either goes slightly airborn or dips down on one side.

Isn't sitting on the bumstops not safe at all? And I don't want to hear I guess so if everyone else's is like that. I need an answer from someone who has been riding on them for a long time. Someone reassure me because I'm a littls ticked off right now and it's getting dark. I'm not taking it apart again at the moment and next step are coilovers when I get the cash so these are going to have to do for now.

P.S. I would have started a new thread, but we have too many of them already since sometimes the 'Search' feature isn't used (which I did lol).
marcustoronto, canada · Jul 2, 2009#21
normal..got it on my trds.
TreyzLong Island, NY · Jul 2, 2009#22
How long and do you drive hard/auto X???
WeeYariGeorgetown, Ontario, Canada · Jul 2, 2009#23
Can't post a pic right now. I have the same gap....and I'm stock. Suspension has never been touched.
GalavoxxSan Francisco · Jul 2, 2009#24
Normal, mine has it too. Over 30k on sportivos with lowering springs. I even had the alignment checked at some point, for fun. It was perfect. Gaps mean nothing. Also, bump stops have nothing to do with this.
TreyzLong Island, NY · Jul 3, 2009#25
From what it seems, the bumpstops do have a play in it.

I rubbed on imperfected dips on the road when I had them on my '07 due to the bumstops being cut from the DF210's. Actually on both sets of springs minus the gap. Now it has magically disappeared, but with the gaps and I'm pretty positivesure that is the reason why. It's probably sitting on the bumpstops hence why it is being pushed up and why we have a gap , BUT if driven for 30K with no problems daily, I see no problem at all. My concern is when it comes to Auto X really due to the harshewr driving conditions one must do.

I need those that have the gap and do Auto X to chime in. I'd like to get back into it, but if I have to wait for coilovers, then I'll keep on doing what I'm doing (show and daily driving).
GalavoxxSan Francisco · Jul 3, 2009#26
I'm running aftermarket bump stops that were fitted to the car by a person who is very knowledgeable about these things. The stops were measured to the correct size and length based on how much my car is lowered. It's possible the "problem" is from the stock uncut bump stops. Looking again at the photo, it does look like the gap might be bigger than mine. I'll have to check on that.
TreyzLong Island, NY · Jul 3, 2009#27
Thanks, I really appreciate it.
lilredrocketDFW, Texas · Jul 3, 2009#28
Everyone made me worry so I checked mine. I have the "GAP". I have had my DF's on for about 15k (with cut bump stops) and they have seen alot of abuse alot in the past 5k. (I'm getting ready to start auto-xing the car so I have been "practicing") I know Acouple of people have been auto-xing on DF's for a while. I think the "GAP" has something to do with it being a single nut set-up and not the more common 3 bolt set-up. I hope this helps if not I'm sure if you ask Tamago or Kngrsll could help shine some light on the subject.
YANNA07Texas · Jul 3, 2009#29
I have a 07 LB with stock suspension. There is a small gap, maybe .3".
talnlnkySpokane, Wa · Jul 5, 2009#30
I was jumping a truck two days ago.. and noticed my STOCK 08 Yaris looks the same... I don't think it matters if its lowered or not.
WeeYariGeorgetown, Ontario, Canada · Jul 5, 2009#31
^^ Agreed.

It would appear that this is one of those things that is noticed and questioned only after performing work on your car. Part of reviewing afterward, and making sure everything is done right and tight. Suddenly, you're going WTF is with this gap, and thinking you've messed up somewhere.
WeeYariGeorgetown, Ontario, Canada · Jul 5, 2009#32
Car sitting on flat level ground. Gap equal on both sides.

You can see how it does move up and down where the rust-proofing is rubbed away.
right (Medium).jpgleft (Medium).jpg
stoufferUK · Jul 5, 2009#33
It doesn't look right... 🙁
AND189australia · Jul 14, 2009#34
frig your bay is dirty mate hit that with some drgreaser and a fire hose