Yarisworld Archive

Chiped....

64 posts · 15,103 views · page 2 of 2

Replies continued

cali yarisCanoga Park, CA · Jun 2, 2009#51
I bought the cheap thing from eBay, then opened it up to find a single resistor.

My understanding from the post above is that we are not talking about unlocking the ECU, we're talking about a piggyback like the UniChip.

If this person is talking about a UniChip tuned for the Yaris, that has some possibility. However, at least here in LA (which is pretty big), there are no UniChip tuners. My impression is that UniChip is much more popular overseas for tuning.

So, this option would have to come already tuned with a plug 'n play harness for the Yaris. The UniChip, while not cheap, would probably be worth it if it can provide 15%+ power gains as quoted.
N3misiSThread starterSouth Africa · Jun 3, 2009#52
Hi Guys, Cali, you are corredct again...

Unichip is extemly popular over here and there is a plug and play harness, it is like a piggy back but there are more options, you can play with timing ignition and vvti and the usual but you can have a wasted spark unit as well, change cams, and keep the performance upgrade!!!!!

And then for the boosted Yaris owners it should be good news, it is not that expensive and the gains and power over your settings is definitily worth it...
marcustoronto, canada · Jun 3, 2009#53
hey can anyone replicate sprint booster or blitz controller.. for maybe 1/4 of the cost.
markitectMichigan · Jun 3, 2009#54
Originally Posted by marcus ↑
hey can anyone replicate sprint booster or blitz controller.. for maybe 1/4 of the cost.
I've been thinking about this:

The accelerator position sensor just has two output voltages.
So my guess is the Blitz/sprint controller is just a simple microcontroller with two analog inputs and two analog outputs, or even simply a rom with a table mapping the input to output and the switch changes an address base. There Might be RMS converters too.

Takes the voltages in, puts them into an equation and outputs the result on the outputs. Add a couple GPIO for the reverse sensing and mode switching, and something for the display.

That said you could use an oscilloscope to see the factory signal as the pedal moves, then come up with a desired signal over the range. Then find a mapping between the two.

You could then get an appropriate microcontroller and build your own.
Possibly design a analog circuit that will perform exactly one mapping.
Or have a rom with a lookup table with the analog inputs addressing it and the value in each address corresponds to the output at that input voltage.(This seem easiest, but someone that programs PIC microcontrollers will probably opt for number 1)
KioshiFremont, CA · Jun 3, 2009#55
I'm keeping an eye on this one, get some money quickly, we all want to see the results ^_^
beardaGermantown, MD · Jun 4, 2009#56
Originally Posted by markitect ↑
I've been thinking about this:

The accelerator position sensor just has two output voltages.
So my guess is the Blitz/sprint controller is just a simple microcontroller with two analog inputs and two analog outputs, or even simply a rom with a table mapping the input to output and the switch changes an address base. There Might be RMS converters too.

Takes the voltages in, puts them into an equation and outputs the result on the outputs. Add a couple GPIO for the reverse sensing and mode switching, and something for the display.

That said you could use an oscilloscope to see the factory signal as the pedal moves, then come up with a desired signal over the range. Then find a mapping between the two.

You could then get an appropriate microcontroller and build your own.
Possibly design a analog circuit that will perform exactly one mapping.
Or have a rom with a lookup table with the analog inputs addressing it and the value in each address corresponds to the output at that input voltage.(This seem easiest, but someone that programs PIC microcontrollers will probably opt for number 1)
I was messing around with doing something similar for my Mazda. I'd started on one design based on a signal ADC/DAC when I found out there were two APS signals and that they had to correlate. If anybody knows of a good cheap microcontroller with a built in two-channel 5V ADC and DAC maybe I'd get it started back up.

My plan was to hold the table in EEPROM and make it configurable over the serial port.
marcustoronto, canada · Jun 4, 2009#57
Originally Posted by bearda ↑
I was messing around with doing something similar for my Mazda. I'd started on one design based on a signal ADC/DAC when I found out there were two APS signals and that they had to correlate. If anybody knows of a good cheap microcontroller with a built in two-channel 5V ADC and DAC maybe I'd get it started back up.

My plan was to hold the table in EEPROM and make it configurable over the serial port.
hope you do start it again..cant wait
CTScottUSA, CT · Jun 4, 2009#58
Originally Posted by bearda ↑
I was messing around with doing something similar for my Mazda. I'd started on one design based on a signal ADC/DAC when I found out there were two APS signals and that they had to correlate. If anybody knows of a good cheap microcontroller with a built in two-channel 5V ADC and DAC maybe I'd get it started back up.

My plan was to hold the table in EEPROM and make it configurable over the serial port.
I use PIC microcontrollers for everything - They're cheap and there are many options for I/O configurations (analog and digital). The DSPIC series have DACs, but I would actually go with a non-DSP one and use I2C DACs like the Microchip TC1321, that way you can chain as many as you need (up to 255 of them). I would really like to have a spare Yaris to experiment with (a wrecked one with a running engine would be fine).
marcustoronto, canada · Jun 4, 2009#59
i knew i should have stayed on my electronic engineering course..it would have come in handy..damn it.
beardaGermantown, MD · Jun 5, 2009#61
Originally Posted by markitect ↑
https://www.silabs.com/products/mcu/...C8051F0xx.aspx

The dev kit is under $100

someone should scope the signal to confirm its really a DC signal though, wish I had some more free time.
Hmm, that micro doesn't look too bad. I'll see if I can get a sample.

I know that on my Mazda I was able to pull APS voltage from the OBD-II PIDS, and it was a 0-5V DC signal. I'll see if I can hook my laptop up to the Yaris this weekend and confirm that it works that same. By the way, you really don't need a whole engine to test this, just the accelerator pedal.
CTScottUSA, CT · Jun 5, 2009#62
Originally Posted by bearda ↑
Hmm, that micro doesn't look too bad. I'll see if I can get a sample.

I know that on my Mazda I was able to pull APS voltage from the OBD-II PIDS, and it was a 0-5V DC signal. I'll see if I can hook my laptop up to the Yaris this weekend and confirm that it works that same. By the way, you really don't need a whole engine to test this, just the accelerator pedal.

The only bad thing about that 8051 based mcu is the amount of support circuitry required. The PICs require far less.

The reason I would like to have a running engine to bench test with, is that I see taking this to the extreme of actually using the microcontroller to even fire the injectors. The injectors are controlled by a PWM signal. For Turbo and SC cars the system could then meter more fuel as required (by tweaking the PWM duty cycle).
chongopantsHouston · Jul 15, 2009#63
Bump! Sounds hoaxy so what happened?
SuperFunBallNSB,FL · Jul 15, 2009#64
I think he gained so much power from the chipping that he broke the space time continuum, never to be seen again.