Yarisworld Archive

Spoiler painted for $25

19 posts · 7,551 views

CreeperOriginal postGeorgia · May 21, 2009#1
got it painted now time to install....shhhh cost me $25 to paint :) again no instructions whats the easiest way to install? stick on with tape then drill or hold it up mark spots then drill and stick on?[ATTACH][ATTACH]Picture not included in this copy[/ATTACH][/ATTACH]

3 attachments not included in this copy

Replies 18

TamagoOff Grid · May 21, 2009#2
very nice :) hold the wing up snug, use a sharpie or a punch to mark the drill points, remove wing, drill holes, insert grommets, use stickytape for wing, stick into place, bolt it up.

if it's an ebay wing you'll HAVE to buy longer bolts. the ones supplied are too short.


i just did this for a YW member a couple days ago :)
TamagoOff Grid · May 21, 2009#3
i recommend either using a step bit or 3 different bits
1/8 inch for pilot

then 1/4 for mid

then final size, what is it, 12mm?
CreeperThread starterGeorgia · May 21, 2009#4
its from yaris universe so it looks like the screws might be a bit to short. thanks for the help though
TamagoOff Grid · May 21, 2009#5
can you shoot a photo of the profided hardware?
ezhacker1San Francisco · May 21, 2009#6
wow, just 25 dollars to get it painted? Im having a headache now about mine..
CreeperThread starterGeorgia · May 21, 2009#7
yeah $25 a guy owed me a favor and happen to ahve his own paint booth so i jsut had to buy the paint.[ATTACH]Picture not included in this copy[/ATTACH]

2 attachments not included in this copy

TamagoOff Grid · May 21, 2009#8
those bushings will crush outwards when compressed?

they look metal!
CreeperThread starterGeorgia · May 21, 2009#9
they are metel. do I need to get new ones? from what i can figure washer goes on screw, screw goes on spoiler, bushing comes from inside the body panel for the screw to screw into and holds it in place. is that not right? its what came with it so thats the best i could tell.
TamagoOff Grid · May 21, 2009#10
Originally Posted by Creeper ↑
they are metel. do I need to get new ones? from what i can figure washer goes on screw, screw goes on spoiler, bushing comes from inside the body panel for the screw to screw into and holds it in place. is that not right? its what came with it so thats the best i could tell.
something needs to compress that metal bushing. set your camera on macro and take another shot of the bushing from a foot away :D
CreeperThread starterGeorgia · May 21, 2009#11
ill see if i can find that setting its a cheap old digital
CreeperThread starterGeorgia · May 21, 2009#12
i cant get a non-fuzzy shot of them, but they are metel and wide on one end with groovs to lock it into place. the other end without the enlarged ring around it is threaded about halfway down
TamagoOff Grid · May 21, 2009#13
ok hmmm... just be careful with the hole drilling, gotta get those bushings TIGHT in place
CreeperThread starterGeorgia · May 21, 2009#14
believe me drilling a hole in my car is going to be extremely hard for me to do and will be double checked about 100 times before that drill gets close to it starting out small and working up in the sizes
TamagoOff Grid · May 21, 2009#15
where in georgia are you? north georgia? if i end up in chatt soon i'm more than willing to drill the holes for you :)
CreeperThread starterGeorgia · May 21, 2009#16
middle west, in columbus.
AlainMikliSF, CA · May 22, 2009#17
you gonna sleep with the spoiler, right👍
metalsharkMesa, AZ · Dec 23, 2009#18
If those nut sleeves are like I've used, put a locking star washer and nut on the bolt with the star washer between the sleeve and the nut. Screw them into the insert and hold the sleeve and nut stationary with an end wrench while tightening the bolt to expand the sleeve below the panel. I'd slip in some RTV when installing these and put the bolts in with blue locktite to keep all water out.,
schleppyBoston, MA · Dec 24, 2009#19
I have the same spoiler, same hardware.

I 3M taped mine to the car. It hasn't budged in months.