Yarisworld Archive

Turbo Manifold thread

64 posts · 40,699 views · page 1 of 2

SabretoothOriginal postSt Cloud FL · May 17, 2009#1
Ok, heres my situation.

I am starting to put together a turbo kit for the Yaris, most of it will end up just being bits and ends here and there. Number one thing in mind is keeping costs below $2500 for an Intercooled setup.

My goals:
Cost at or just above $2500
No engine management
6PSI
Intercooled
Power goal: 160whp

Should be obtainable reasonably.
Step 1 was finding a turbo manifold for the car, so I started rooting around and found 2 options. Turbotoyotas.com manifold, then this sucker.

http://cgi.ebay.com/ebaymotors/03-06...Q5fAccessories

Its a cast iron piece, set for a T25/GT28 Turbo. OEM fitment. Only issue, its a Scion Xb/Xa Manifold.

Pics:
Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy




Any suggestions?

Replies 63

gwasabiHonolulu, Hawaii · May 17, 2009#2
You get what you pay for! lol
SabretoothThread starterSt Cloud FL · May 17, 2009#3
Well I know that, just wondering if a cast iron part is better off than a welded one.

lol, just as a warning, Tamago is gonna have a field day with your statement if he finds it.
SabretoothThread starterSt Cloud FL · May 17, 2009#4
I might just buy it anyway...
Only way someone will know is to test it.
cali yarisCanoga Park, CA · May 18, 2009#6
Remember how you had to remove your power steering to make room for that?

We have electronic p/s on our cars, so I think Jess' mani would fit just fine. Overkill for 6 psi though.
gwasabiHonolulu, Hawaii · May 18, 2009#7
Originally Posted by Sabretooth ↑
Well I know that, just wondering if a cast iron part is better off than a welded one.

lol, just as a warning, Tamago is gonna have a field day with your statement if he finds it.

i know that guy is always on my ass.
battleversiontc808 · May 18, 2009#8
cast is better then welded can stand up to the heat but welded you can atleast reposition the angle. and the cast supposedly flows worse cause stay all ruff and whatevers inside not as clean as welded
TamagoOff Grid · May 18, 2009#9
Originally Posted by gwasabi ↑
i know that guy is always on my ass.
you bring it on yourself
cali yarisCanoga Park, CA · May 18, 2009#10
This manifold wont work, the A/C lines from the firewall would be in the way.
What if you don't have A/C lines? 😁 -- I don't.
TamagoOff Grid · May 18, 2009#11
Originally Posted by cali yaris ↑
What is you don't have A/C lines? 😁 -- I don't.
still don't understand why you'd do that...... delete something that doesn't need to be deleted..
cali yarisCanoga Park, CA · May 18, 2009#12
^ You've made that opinion clear before. If you ever ask a question instead, I'd be happy to answer it.
TamagoOff Grid · May 18, 2009#13
Originally Posted by cali yaris ↑
^ You've made that opinion clear before. If you ever ask a question instead, I'd be happy to answer it.
why?
gwasabiHonolulu, Hawaii · May 18, 2009#14
Originally Posted by Tamago ↑
you bring it on yourself
lol you dont have to comment on everything i say though. maybe like once in a while ignore me? lol

Thsat turbine tech one looks like its going up? i dunno lol
cali yarisCanoga Park, CA · May 18, 2009#15
why?
1. I never, ever use my a/c so i have no need for it.
2. I'm saving 18 pounds of weight and clearing out the engine bay.
3. I'm trying to squeeze every horsepower I can out of this motor, and however small, this will make a difference. (yes, I know there are a lot more things I can do in this regard)
4. This gets the condenser out of the way of the radiator, easier to fab/install a custom radiator later.
5. I'm also converting the water pump to electric, so I want to see what the car is like with just two pulleys.
6. A panda on the hood is not "needed" either, but it's what you like -- this is what I like.
TamagoOff Grid · May 18, 2009#16
Originally Posted by gwasabi ↑
lol you dont have to comment on everything i say though. maybe like once in a while ignore me? lol

Thsat turbine tech one looks like its going up? i dunno lol
i ignored your original comment, didn't i?
CASTREXCosta Rica · May 18, 2009#17
Back on topic....

You can get the bends and turbo flangers here:

http://www.jgstools.com/turbo/index2.html

You would only need take out the OE exhaust manifold and take it to a shop to have the engine flanger done and welded to the rest...


You can duplicate the manifold design from Turbotoyotas (Cali's manifold) simple and functional.


Sure an EL mani is cool... but hard to fit on a Yaris and not really needed for the low boost levels this engine will ever see...


... And regarding the Cast vs welded tubular design.

Cast manifolds will always beat the tubulars on reliability and longevity that's why must of the OE turbo cars use as cast manifold. nothing wrong with them.

Tubular welded manifolds will usually flow better and provided more power... plus they look nicer.

But then again, all this is irrelevant at the boost levels this engine will see...
Russelt3hPirateEpcot · May 18, 2009#18
why intercool it?

might as well make things easier and not intercool.

it'd be a lot cheaper too.
TamagoOff Grid · May 18, 2009#19
Originally Posted by Russelt3hPirate ↑
why intercool it?

might as well make things easier and not intercool.

it'd be a lot cheaper too.
a car isn't turbo unless it has an intercooler. and it's not making real power unless it's a front mount.

didn't you know?
Nexus1155Dorchester · May 18, 2009#20
loloolol, we don't know if you'll get det though from not running and intercooler... holdeners kit blew the engine when he was close to done tuning it with no intercooler...

Next im sure well get someone in here saying 6psi on a GT20 is the same as 6psi on a GT30 :D
TamagoOff Grid · May 18, 2009#21
Originally Posted by cdydjded ↑
Safer, makes more power, less likely for detination, easier is not better, what is cheap now will cost you more later
6psi, intercooler is a waste.

run meth injection instead.
TamagoOff Grid · May 18, 2009#22
Originally Posted by Nexus1155 ↑

Next im sure well get someone in here saying 6psi on a GT20 is the same as 6psi on a GT30 :D
not from me you won't
Nexus1155Dorchester · May 18, 2009#23
hahaha i really lol'ed when i read that tamago....... but he's got a point, meth injection would be a feasable option to stabilize the balance, it would be about the same amount of money it would cost for an intercooler and piping, if not less. AND it would be less charge travel through pipes so not much efficiency loss... I say he's got a damn good point...
TamagoOff Grid · May 18, 2009#24
Originally Posted by cdydjded ↑
=what is cheap now will cost you more later
you mean something along the lines of running half an FIC and unplugging the stock o2 sensor?
TamagoOff Grid · May 18, 2009#25
Originally Posted by cdydjded ↑
A front mount does not need to be refilled, I think the waste would be refilling that little bottle every other day. Your comment makes no sense 😕, why would a cooler, denser air charge be a a waste? Please think before you answer, I do not generalities........
let's see..

small engine

small turbo

15 feet of intercooler piping

1 psi drop thru cooler..

just to be able to say you have a front mount?

i'm not anti-intercooler, i just think front mounts are retarded in low boost applications. even the supra TT came with simple side mount intercoolers FROM THE FACTORY.

and since when does one burn through 2 gallons of water/meth every other day? you don't know anything about meth injection do you?

oh and i find it funny you say you RAN a speed shop in miami. what happened? RAN? why not RUNNING?
TamagoOff Grid · May 18, 2009#26
Originally Posted by cdydjded ↑
Listen, based on your smart ass remark I can tell you never used a FIC & have a reading comprehension problem. The FIC has 4 programable maps. Fuel, Ignition, O2 & MAF. AEM recomends to use the least amount of maps. Right now I have control of Fuel & Timing. Im not running a turbo yet so there is no need to clamp the MAF or manipulate the O20 signal. So basically its installed & works. Also I did not unplug the stock O2 sensor, I unplug the connection from the FIC to the O2.
1. i have an FIC mounted and wired by me in my car.
2. iirc you already burned up your stock o2 sensor..

bad wiring?
TamagoOff Grid · May 18, 2009#27
Originally Posted by cdydjded ↑
Congratulation on havin a FIC, based on what facts do you claim I burned my O2?
Originally Posted by cdydjded ↑
I disconnected the connection to the O2 & still have a CEL, I might have screwed up the O2

🤷

and what happened to you being SO SURE that i know nothing about the FIC? 😆
TamagoOff Grid · May 18, 2009#28
Originally Posted by cdydjded ↑
Is that the best you can do, answer a question with a question, your an empty suit
trust me, you don't want the best i can do.

good luck to you on your failing mission
PETERPOOPOahu · May 18, 2009#29
tamago FTL
TamagoOff Grid · May 18, 2009#30
Originally Posted by cdydjded ↑
Thats it? An ultimatum? Thats all you got? I want to see the best you can do, ohh I know you can put a panda sticker on you hood 👍
i've already proven what i set out to prove, 65whp over stock, under $1000 spent.

and the panda is certainly not a sticker.
TamagoOff Grid · May 18, 2009#31
Originally Posted by cdydjded ↑
Wow good job, $1000 & 65HP, congrats, woop-t-doo! So if I do 66HP @ $999 & I better than you? King Tamago? Was the panda paint by numbers then?
you're joining the penis shit list.. i mean peterpoop..


g'bye and good luck yet again.. i'll keep an eye out for you looking for a replacement block after you destroy the one you're on now.
TamagoOff Grid · May 18, 2009#32
Originally Posted by cdydjded ↑
Now you look into the future & see me destroying my block, man your good, do you speak from experience? How many blocks did your $1000 turbo kit brake?
not a one.


let's see


my kit worked.

and you're still screwing around with an FIC



me 1

you.. 0?
TamagoOff Grid · May 18, 2009#33
Originally Posted by cdydjded ↑
Im an innovator, you a follower.....
you're innovating like crazy there 😆

and if i'm a follower, i would have bought a kit.
TamagoOff Grid · May 18, 2009#34
Originally Posted by cdydjded ↑
Here is the definition for innovator, it 4 syllables, I know that might be a tough word for you:
"An innovator or pioneer in a general sense is a person or an organisation who is one of the first to do something and often opens up a new area for others and achieves an innovation"
I am the first to get the FIC to work.....you did not buy one cause your cheap!
you have NOT gotten the FIC to work. you have CEL's.

if you think what i did for my turbo setup is not innovative, then 🤷 not my problem??
TamagoOff Grid · May 18, 2009#35
cool, good luck to you.
battleversiontc808 · May 18, 2009#36
your not the first to be running it i have been running it for 2 months now successfully
Originally Posted by cdydjded ↑
Here is the definition for innovator, it 4 syllables, I know that might be a tough word for you:
"An innovator or pioneer in a general sense is a person or an organisation who is one of the first to do something and often opens up a new area for others and achieves an innovation"
I am the first to get the FIC to work.....you did not buy one cause your cheap!
TamagoOff Grid · May 18, 2009#37
Originally Posted by battleversiontc ↑
your not the first to be running it i have been running it for 2 months now successfully
ooooooooooooooooooooooooooooooooooooofff
battleversiontc808 · May 18, 2009#38
off what im not saying i was the first im pretty sure somebody othere has successfully ran it maybe havent posted here or anywhere
cali yarisCanoga Park, CA · May 19, 2009#39
^ on a Yaris?
ParmasML · May 19, 2009#40
Originally Posted by Sabretooth ↑
Ok, heres my situation.

I am starting to put together a turbo kit for the Yaris, most of it will end up just being bits and ends here and there. Number one thing in mind is keeping costs below $2500 for an Intercooled setup.

My goals:
Cost at or just above $2500
No engine management
6PSI
Intercooled
Power goal: 160whp

Should be obtainable reasonably.
Step 1 was finding a turbo manifold for the car, so I started rooting around and found 2 options. Turbotoyotas.com manifold, then this sucker.

Its a cast iron piece, set for a T25/GT28 Turbo. OEM fitment. Only issue, its a Scion Xb/Xa Manifold.

Any suggestions?
If you are interested in using a GT28 Turbo I have the turbo mainfold that came with the engine. The only reason I custom made another mainfold was because it was designed to fit left hand drive yaris. The mainfold was custom made by Jess from Turbine Tech for the echo of turboecho2005.

And btw guys don't ruin other's thread by flaming each other here 😠 🤮
TamagoOff Grid · May 19, 2009#41
Originally Posted by Parmas ↑
If you are interested in using a GT28 Turbo I have the turbo mainfold that came with the engine. The only reason I custom made another mainfold was because it was designed to fit left hand drive yaris. The mainfold was custom made by Jess from Turbine Tech for the echo of turboecho2005.

And btw guys don't ruin other's thread by flaming each other here 😠 🤮
how much do you want for the manifold?
SabretoothThread starterSt Cloud FL · May 19, 2009#42
Originally Posted by Parmas ↑
And btw guys don't ruin other's thread by flaming each other here 😠 🤮


TY!

I havnt been on in 24 hours, to find a flame war has started in my semi-innocent thread...take it to a PM thread, or better yet...you guys can swap IM accounts, then flame war AIM.
TamagoOff Grid · May 19, 2009#43
Originally Posted by Sabretooth ↑
TY!

I havnt been on in 24 hours, to find a flame war has started in my semi-innocent thread...
good luck hitting 160whp at 6psi with no engine management ;)
SabretoothThread starterSt Cloud FL · May 19, 2009#44
Well im not worried if I dont hit it, its just a benchmark that I want to hit...I am not saying that engine management wont be down the road. It wont be on the car when its first put together...just added as a later upgrade for more HP.

The point is to have somewhere to start before deciding to upgrade
TamagoOff Grid · May 19, 2009#45
Originally Posted by Sabretooth ↑
Well im not worried if I dont hit it, its just a benchmark that I want to hit...I am not saying that engine management wont be down the road. It wont be on the car when its first put together...just added as a later upgrade for more HP.

The point is to have somewhere to start before deciding to upgrade
expect about 130whp

but i'll applaud you if you DO hit the ##

for the money, why not buy the HKS kit?
SabretoothThread starterSt Cloud FL · May 19, 2009#46
I also saying this now, to clear it up. I am not intending to make monster HP with this car, I will leave that for my next car that I aquire.

My intentions are to make this car a bit faster than what it is. Sporty-ecnobox if you must...Kinda an oxymoron tho.
SabretoothThread starterSt Cloud FL · May 19, 2009#47
HKS has a kit available for the US? or are you making reference to the Xb kit?
TamagoOff Grid · May 19, 2009#48
Originally Posted by Sabretooth ↑
I also saying this now, to clear it up. I am not intending to make monster HP with this car, I will leave that for my next car that I aquire.

My intentions are to make this car a bit faster than what it is. Sporty-ecnobox if you must...Kinda an oxymoron tho.
so, $2500 will buy you a kit that you can use 90% of, and sell off what you don't end up using.

sounds like a better plan to me than piecing together something that you'll STILL have to have a custom downpipe made for
TamagoOff Grid · May 19, 2009#49
Originally Posted by Sabretooth ↑
HKS has a kit available for the US? or are you making reference to the Xb kit?
i'm referring to the xB HKS kit.
TamagoOff Grid · May 19, 2009#50
Picture not included in this copy