Yarisworld Archive

Belt noise?

21 posts · 15,387 views

Cutie Pie #2Original postDelta,PA · May 17, 2009#1
This morning, when I started the car there was a quick squeak noise. Don't know if it had something to do with the rain we had(it rained it's ass off last night, and cooler morning than we have had) or if it is something wearing out within the belt area. It only made the noise for about 5-7 seconds, then went away, car seemed to run good. It did make this noise before, but not as loud and long (1 second ) in the cooler weather. Any thoughts please?

Replies 20

severous01SE Texas · May 17, 2009#2
well...sounds like some time for basic maintenance.

get a new one. it's already been burnt. i'd replace it, and for 10-20 bux it's not gonna kill ya
YAR1SRaleigh, NC · May 17, 2009#3
the rain does funny things to the yaris....
I left mine sitting in the rain for 3 days and it took a few trys to start it up.
AothachosLong Island, NY · May 17, 2009#4
yea rain and my yaris do not mix at all, after it rains the next day i start my car it starts up fine its just when it does start up it sounds like it died for .5 seconds then it goes va-vroooooooooom!!!!!!!! up to close to 3rpm then drops down to 2rpms in 3 seconds.......yea its rained so much i counted it =P but otherwise i think its normal really the belt gets wet and the pullies try to catch it when theres water between them, it happens to me but rarely, well also i have nst pulley set too
Sir A.Y. AtoyotSurrey, BC Canada · May 17, 2009#5
Originally Posted by Aothachos ↑
yea rain and my yaris do not mix at all, after it rains the next day i start my car it starts up fine its just when it does start up it sounds like it died for .5 seconds then it goes va-vroooooooooom!!!!!!!! up to close to 3rpm then drops down to 2rpms in 3 seconds.......yea its rained so much i counted it =P but otherwise i think its normal really the belt gets wet and the pullies try to catch it when theres water between them, it happens to me but rarely, well also i have nst pulley set too
The owner's manual says that you aren't supposed to touch the throttle when it's starting. Possibly it's vroooming because you're expecting it to be hard to start and are stepping on the throttle unconsciously?
ruimondPerth, Australia · May 17, 2009#6
When i installed a new belt for my NST underdrive pulley, my mechanic said if it made any squeaks when starting up i would have to tighten my belt.

Im guessing the same would apply to the noise you may be hearing if its the belt. It is just slipping and getting abit loose, but once it warms up it grips better.

You could try tightening the belt first if you have much tightening left. You can see how much more you can tighten on the silver/grey leaver with the bolt just above all the pulleys. Otherwise as someone said early you should just replace the belt they are pretty cheap.
yaris-meAnaheim, CA · May 18, 2009#7
The belt should be adjusted. Feel under the belt and if it's cracked or brittle, then it should be replaced.
devinlamotheSudbury, Canada · May 18, 2009#8
To those saying the belt needs to be replaced ... I'm not so sure. I JUST got my belt replaced and re-tightened, all was fine for a couple months and now the 'squeel' is back. Not sure what it is. Could be a bearing or something on the pully.
1stToyotaOklahoma · May 18, 2009#9
Have somebody check the tension, and I doubt the rain was the problem...just had 22 straight days of rain and never heard a peep out of my belt during start up. If tension is okay, replace. Don't over-tighten...guessing 100lbs should be about right, and 125lbs max? 125lbs-150lbs might cause premature wear in Alt, W/P, etc...new belt will need to be readjusted within the first few hundred miles.
Cutie Pie #2Thread starterDelta,PA · May 18, 2009#10
Belt seems to be tight enough , I will take it in, if I hear the noise again. Car has 25,000 miles on it.
saplaymateSATX · May 18, 2009#11
If it just for a couple of seconds in the morning when cold, not a big deal, as long as it's not cracking. If it is slipping when accelerating once running then your loose.
AothachosLong Island, NY · May 19, 2009#12
Originally Posted by ruimond ↑
When i installed a new belt for my NST underdrive pulley, my mechanic said if it made any squeaks when starting up i would have to tighten my belt.

Im guessing the same would apply to the noise you may be hearing if its the belt. It is just slipping and getting abit loose, but once it warms up it grips better.

You could try tightening the belt first if you have much tightening left. You can see how much more you can tighten on the silver/grey leaver with the bolt just above all the pulleys. Otherwise as someone said early you should just replace the belt they are pretty cheap.
no i never touch the throttle lol i just start it and thats it, i never touch it
supmetSouthern California · May 19, 2009#13
Originally Posted by saplaymate ↑
If it just for a couple of seconds in the morning when cold, not a big deal, as long as it's not cracking. If it is slipping when accelerating once running then your loose.
LOL. worst. advice. ever.

fix things BEFORE they put you in deadly situations...

my oil light only comes on when its really hot out and I drive it hard, should I wait til I snap a rod to get it taken care of?
saplaymateSATX · May 19, 2009#14
your a moron
supmetSouthern California · May 19, 2009#15
Originally Posted by saplaymate ↑
your a moron
Sorry, I'll post in bold and magenta, and misuse your/you're from now on so people think I'm super smart.

Seriously though, if its making noise its out of adjustment - why wait for it to snap or fall off?
1stToyotaOklahoma · May 20, 2009#16
Originally Posted by supmet ↑
Sorry, I'll post in bold and magenta, and misuse your/you're from now on so people think I'm super smart.

Seriously though, if its making noise its out of adjustment - why wait for it to snap or fall off?
And why wait for the micro-v ribs to develope a glazed surface that doesn't grip too well, because of the slipping at start up?
AothachosLong Island, NY · May 21, 2009#17
take a pair of scissors and cut the belt, take out the belt, oil up ur pullies and then thats it, the noise should be gone =)
cleongSingapore · May 22, 2009#18
Easy on the name calling.

But yes, a squealing belt is a problem - a correctly tensioned belt will not squeal. The belt runs your water pump and alternator, so your car could fail in a bad way if the water pump goes.
1stToyotaOklahoma · May 22, 2009#19
Originally Posted by Aothachos ↑
take a pair of scissors and cut the belt, take out the belt, oil up ur pullies and then thats it, the noise should be gone =)
...and replaced with a cracked head/blown head gasket?
AothachosLong Island, NY · May 22, 2009#20
Originally Posted by 1stToyota ↑
...and replaced with a cracked head/blown head gasket?
cut your exhaust off so that it is loud enough to cut out the sound 😉
1stToyotaOklahoma · May 22, 2009#21
Originally Posted by Aothachos ↑
cut your exhaust off so that it is loud enough to cut out the sound 😉
and take off your wheels and tires and sell them because the car won't be needing them with a blown motor...or better yet, keep the belt where it's at; don't cut it off and throw it away.