reading different things. but happy to say at least i have narrowed down problem of my previous posts on here.
PO420.....so now what?
46 posts · 43,600 views
Replies 45
???
A code P0420 may mean that one or more of the following has happened:google ftw
- Leaded fuel was used where unleaded was called for
- An oxygen sensor is not reading (functioning) properly
- The engine coolant
temperature sensor is not working properly- Damaged or leaking exhaust manifold
/ catalytic converter / exhaust pipe- Retarded spark timing
- The oxygen sensors in front and behind the converter are reporting too similar of readings
Some suggested steps for troubleshooting a P0420 code include:
- Check for exhaust leaks at the manifold, pipes, catalytic converter. Repair as required.
- Use a scope to diagnose the oxygen sensor operation (Tip: The oxygen sensor in front of the catalytic converter normally has a fluctuating waveform. The waveform of the sensor behind the converter should be more steady).
- Inspect the downstream heated oxygen sensor (HO2), replace if necessary
- Replace the catalytic converter
Hi
I would say it´s probably the oxygensensor when it says bank 1.
Regards Steven.
I would say it´s probably the oxygensensor when it says bank 1.
Regards Steven.
Now you Google the code and see what it means.
it can mean a lot of things indeed, but mostly that your catalytic converter is not working properly. Have you done any kinds of mods to your car?
You best bet is to take it to the dealer to check... Or you can just clear the code and hope it does not show up again..
You best bet is to take it to the dealer to check... Or you can just clear the code and hope it does not show up again..
and now re-reading your previous thread about putting diesel in the car, it's quite likely that the code is just a temporary one as the sensors didn't like the way the diesel fumes interacted with them. But, there's also a possibility that your catalytic converters are damaged, so taking it to the dealer is still the best bet.
well fuel was put in over a month ago now or more actually. indicator light has been reset once by toyota and once by a mechanic in glendora,ca. the one that said oh okay yes its spark plugs and charges $138.00. thats what pushed me to buy this reader. even though i have seen worse in the past. did i miss anything? oh probably!Originally Posted by eTiMaGo ↑and now re-reading your previous thread about putting diesel in the car, it's quite likely that the code is just a temporary one as the sensors didn't like the way the diesel fumes interacted with them. But, there's also a possibility that your catalytic converters are damaged, so taking it to the dealer is still the best bet.
I'm sorry, I really don't think there's anything anyone here can do to help... If you don't wanna go see the dealer again (understandable), reset the code and cross your fingers it does not show up again...
well its not a matter of not wanting to go to dealership. i am curisous about this almost 1000 dollar estimate mt grandma got through toyota. from what i read it looks like there is a warranty for catalytic converter up to 80,000 miles. probably read wrong though.Originally Posted by eTiMaGo ↑I'm sorry, I really don't think there's anything anyone here can do to help... If you don't wanna go see the dealer again (understandable), reset the code and cross your fingers it does not show up again...
even with google, or software that i got. it still doesn't narrow it down as much as i would like.Originally Posted by Loren ↑Now you Google the code and see what it means.
no modsOriginally Posted by eTiMaGo ↑it can mean a lot of things indeed, but mostly that your catalytic converter is not working properly. Have you done any kinds of mods to your car?
You best bet is to take it to the dealer to check... Or you can just clear the code and hope it does not show up again..
basic and simple yaris here
something wrong with the catalytic converter, i don't see how it can be more detailed than that 😁
If there is a warranty on it, and if they don't revoke it due to the diesel incident, then do it!
If there is a warranty on it, and if they don't revoke it due to the diesel incident, then do it!
well but then again doesn't that code MAYBE mean that? what about the maybe spark timing? or maybe a hose not sealed or a plug not tight, etc.Originally Posted by eTiMaGo ↑something wrong with the catalytic converter, i don't see how it can be more detailed than that 😁
If there is a warranty on it, and if they don't revoke it due to the diesel incident, then do it!
the code p0420 from what i have looked up seems to be a common one and one with one too many possibilities. but of course. warranty = $0 at least the last time i checked. also correct me if im wrong but toyota did say wrong plugs are in, well not the brand they want are in. so that would hopefully make this a warrantable fix. no need to bring up deisel being put in over a month ago and what not.
Stored:
P0420 Catalyst System Efficiency Below Threshold (Bank 1)
Pending:
P0420 Catalyst System Efficiency Below Threshold (Bank 1)
MIL ON
MisFire Monitor Complete
Fuel System Monitor Complete
Comprehensive Component Monitor Complete
Catalyst Monitor Complete
Heated Catalyst Monitor Not Supported
Evaporative System Monitor Complete
Secondary Air System Monitor Not Supported
A/C System Refrigerant Monitor Not Supported
Oxygen Sensor Monitor Complete
Oxygen Sensor Heater Monitor Complete
EGR System Monitor Not Supported
DTC for which Freeze Frame was Stored P0420
Fuel System 1 Status Closed Loop
Fuel System 2 Status Not Supported
Calculated LOAD Value 77.25 %
Engine Coolant Temp 181.40 °F
Short Term Fuel Trim - Bank 1 5.47 %
Long Term Fuel Trim - Bank 1 -0.78 %
Engine RPM 2339 rpm
Vehicle Speed Sensor 54.68 mph
Ignition Timing Advance #1 Cylinder 25.00 °
Intake Air Temperature 69.80 °F
Air Flow Rate Mass Air Flow Sensor 2.57 lb/min
Absolute Throttle Position 28.24 %
Time Since Engine Start 1071 sec
Bank 1 - Sensor 1 Equivalence Ratio 1.06
Bank 1 - Sensor 1 O2S Voltage 3.44 V
Commanded Evaporative Purge 100.00 %
# Warm-ups since DTC Cleared 3
Distance since DTC Cleared 27.34 mi
Barometric Pressure 28.94 inHg
Bank 1 - Sensor 1 Equivalence Ratio 1.06
Bank 1 - Sensor 1 O2S Current 0.09 mA
Catalyst Temperature Bank 1 - Sensor 1 1274.90 °F
Catalyst Temperature Bank 1 - Sensor 2 1274.90 °F
Control Module Voltage 13.85 V
Absolute Load Value 56.08 %
Commanded Equivalence Ratio 0.97
Relative Throttle Position 10.98 %
Absolute Throttle Position B 62.75 %
Accelerator Pedal Position D 25.10 %
Accelerator Pedal Position E 41.18 %
Commanded Throttle Actuator 28.24 %
Time since DTC Cleared 0 hr 53 min
Here's as detailed as you can get:
P0420 Catalyst System Efficiency Below Threshold (Bank 1)
Causes:
- Front exhaust pipe (with Three-Way Catalytic Converter)
- Gas leakage from exhaust system
- A/F sensor (sensor 1)
- HO2 sensor (sensor 2)
If it was a timing error or plug not tight, you'd have a different code, that's the whole reason for being of these diagnostic codes, to help you pinpoint the problem, not maybe something else 😁
Thanks for posting the stored freeze frame value, quite interesting! Only thing that I think is out of order: Bank 1 - Sensor 1 O2S Voltage 3.44 V
Looking at the repair manuals the normal range for this sensor should be usually less than 1V? So yes, in this case, it seems to narrow the problem down to the O2 sensor being defective. But don't take my word for it, I am not a qualified mechanic, just a geek who likes to look up and understand technical information 😁
P0420 Catalyst System Efficiency Below Threshold (Bank 1)
Causes:
- Front exhaust pipe (with Three-Way Catalytic Converter)
- Gas leakage from exhaust system
- A/F sensor (sensor 1)
- HO2 sensor (sensor 2)
If it was a timing error or plug not tight, you'd have a different code, that's the whole reason for being of these diagnostic codes, to help you pinpoint the problem, not maybe something else 😁
Thanks for posting the stored freeze frame value, quite interesting! Only thing that I think is out of order: Bank 1 - Sensor 1 O2S Voltage 3.44 V
Looking at the repair manuals the normal range for this sensor should be usually less than 1V? So yes, in this case, it seems to narrow the problem down to the O2 sensor being defective. But don't take my word for it, I am not a qualified mechanic, just a geek who likes to look up and understand technical information 😁
I totally respect that about you. thanks for your input. i do have to ask though... does this mean o2 sensor is problem(maybe) in lieu of expensive catalytic converter. too many questions. i know, i know.Originally Posted by eTiMaGo ↑Here's as detailed as you can get:
P0420 Catalyst System Efficiency Below Threshold (Bank 1)
Causes:
- Front exhaust pipe (with Three-Way Catalytic Converter)
- Gas leakage from exhaust system
- A/F sensor (sensor 1)
- HO2 sensor (sensor 2)
If it was a timing error or plug not tight, you'd have a different code, that's the whole reason for being of these diagnostic codes, to help you pinpoint the problem, not maybe something else 😁
Thanks for posting the stored freeze frame value, quite interesting! Only thing that I think is out of order: Bank 1 - Sensor 1 O2S Voltage 3.44 V
Looking at the repair manuals the normal range for this sensor should be usually less than 1V? So yes, in this case, it seems to narrow the problem down to the O2 sensor being defective. But don't take my word for it, I am not a qualified mechanic, just a geek who likes to look up and understand technical information 😁
keep in mind that i have not read manual on this code reader so i only had about 2 minutes earlier yesterday to plug in and see if anything would happen. im wondering when i try it out today. is there more i can do while using the reader to get more info. or is it really as simple as plug in. wait, unplug and view on pc? im not even sure how i did that freeze frame thing. time to look into that. thanks geek 🙌
well the way I see it, either something wrong with the cat is causing the (perfectly fine) sensor to read out of range, or the sensor itself is faulty. Without a Toyota technician's actual computer tester unit ($2000+ on eBay), there's no way to know without physical inspection.
appreciate it!
the sensor should flux between 0-about 1.5 (or up to 3 ) I can't remember correctly but it should flux because of the 4-strokes causing a cyclic reading from around 0 to around 1.5 or 3 and back... if it stays high that means you have still a rich mix or the sensor is damaged, and it if left unattended will eventually burn up the cat. if it hasn't already.
how many miles?
This code is VERY common on modded cars with OBD2 equipped systems.
Most people don't worry, as it generally means catalyc inefficiency. Hope that's all it means for you. I'd ignore it and keep on driving, and have been on many of my track cars.
Most people don't worry, as it generally means catalyc inefficiency. Hope that's all it means for you. I'd ignore it and keep on driving, and have been on many of my track cars.
around 21, 22,000 miles on vehicle.Originally Posted by BLAZINBLUEVITZ ↑how many miles?
a couple other people asked me if i have modified or done anything. just a simple yaris here with the most PATHETIC cup holders i have ever seen. so yeah...i had to get that. feels better already.Originally Posted by anonymous user ↑This code is VERY common on modded cars with OBD2 equipped systems.
Most people don't worry, as it generally means catalyc inefficiency. Hope that's all it means for you. I'd ignore it and keep on driving, and have been on many of my track cars.
Air/fuel ratio sensor(AFS B1 S1) voltage should be around 2.8V to 3.8V idling. Stoichiometry is at 3.3V. A voltage of 3.44V means a lean condition (A/f ratio sensor output is the opposite of what happens in a oxygen sensor).
I'm assuming it may be the catalytic converter because of your previous problem. Since you accidentally ran diesel and gas, it didn't burn completely when trying to drive the car which dumped a bunch of raw fuel onto the Cat causing it to overheat and slowly deteriorate. Also some diesel fuel was probably still in the system after draining it plus mixed with higher octane fuel(resists detonation) caused the engine to slowly dump unburned fuel onto the cats. Which is probably why it took awhile for a CEL to come on.
I would test out the O2 sensor(sensor 2) to check for proper operation since it is cheapest to replace and then replace the cat if all sensors check out correctly.
I'm assuming it may be the catalytic converter because of your previous problem. Since you accidentally ran diesel and gas, it didn't burn completely when trying to drive the car which dumped a bunch of raw fuel onto the Cat causing it to overheat and slowly deteriorate. Also some diesel fuel was probably still in the system after draining it plus mixed with higher octane fuel(resists detonation) caused the engine to slowly dump unburned fuel onto the cats. Which is probably why it took awhile for a CEL to come on.
I would test out the O2 sensor(sensor 2) to check for proper operation since it is cheapest to replace and then replace the cat if all sensors check out correctly.
Originally Posted by FunctionSpec ↑Air/fuel ratio sensor(AFS B1 S1) voltage should be around 2.8V to 3.8V idling. Stoichiometry is at 3.3V. A voltage of 3.44V means a lean condition (A/f ratio sensor output is the opposite of what happens in a oxygen sensor).
hmmm guess I had the lean/rich backwards
1/30/09 - fucked up carOriginally Posted by FunctionSpec ↑Air/fuel ratio sensor(AFS B1 S1) voltage should be around 2.8V to 3.8V idling. Stoichiometry is at 3.3V. A voltage of 3.44V means a lean condition (A/f ratio sensor output is the opposite of what happens in a oxygen sensor).
I'm assuming it may be the catalytic converter because of your previous problem. Since you accidentally ran diesel and gas, it didn't burn completely when trying to drive the car which dumped a bunch of raw fuel onto the Cat causing it to overheat and slowly deteriorate. Also some diesel fuel was probably still in the system after draining it plus mixed with higher octane fuel(resists detonation) caused the engine to slowly dump unburned fuel onto the cats. Which is probably why it took awhile for a CEL to come on.
I would test out the O2 sensor(sensor 2) to check for proper operation since it is cheapest to replace and then replace the cat if all sensors check out correctly.
1/31/09 - "fixed car" to a a certain extent. LIGHT NOW ON!
2/10/09 - grandma worrying about light on. takes to toyota they say under $1,000
2/11/09 - grandma takes to route 66 tires and auto in glendora. was there for misc crap but he gave her his word spark plugs are fine. LIGHT OFF
3/14/09 - OH SHIT! LIGHT BACK ON! grandma furious😈 and takes back to route 66 tires and auto in glendora.now he changes mind and says oh yeah, bad bad plugs. replaces them. $138.00. LIGHT OFF NOW
3/16/09 - LIGHT BACK ON!
in meantime im pondering and decide to but innova code reader. and here we are....
just for anyone who did not see orignal post on here. im sure i'll get in trouble by some on here for re-posting. well, sorry.
Okay, so it was around the end of january when my sister ended up calling home saying car pooped out on freeway. i go and see if i can get it going. i cant.
car gets towed to house. im wondering what it could be. since car turns over. 2 times the car has not started in the past and i had to jump it. finally we got a new battery through toyota. so i knew it wasn't that. in the morning my grandma is asking well now what the hell are we going to do. i have a friend of a friend who is one of those all around do it yourself guys. but he mainly is into cars, racing, etc. i have seen him do many miracles, tricks and what not on old chevys and fords. so im keeping him in the back of my head. i then go out to car again to try and get it going thats when i find the reciet that states $10.22 was filled into car last night. and oh my gosh, what does it say? diesel fuel. almost 5 gallons total. so i call toyota to see what they could do. im debating if i should state that there is diesel fuel in car. well i told them and they say that well that voids the warranty, at least for that repair. so basically $90+ an hour for mechanic. and all these other things he is naming off they would have to do. looking over 5 or $600. okay, no way. thats when i call that guy. he comes over, taste fuel says oh yeah its diesel. we empty all the fuel into a 5 gallon bucket. goes right to the very top. im thinking cool, lets fill it and were done. he says no, spark plugs may be shot. now keep in mind i dont know too much about mechanics of cars. he looks at them says i can try cleaning them i think he said, but then decided no, lets get new ones. there cheap. so we get AUTOLITE Part # XP3924. now we fill with premium fuel. try starting and nothing. he then says lets go back to auto zone. we buy a can of ether. im getting a bit worried, becuase i know my grandma is used to the "normal" or whats normal to her. taking to toyota and paying bucks and thats it. anyway. spraying ether into if i remember correctly the air filter or vent, something like that. intake i forget honestly. that gets it going. something else while thats being done is someone else has the fuel line going to the engine unplugged and is holding it and letting that fuel go into a 1 gallon empty thing of oil. thats when he was pretty certain all the diesel was out of it. car had lots of white smoke coming from the exhaust, it was a bit funny feeling and shaking. but after drive around block a couple times. it was perfect. now is when i notice maitnece light on. engine light or the oil light was already on. i ask him whats up. says its probably because there not toyota plugs in. 2 weeks later grandma decides to take it to toyota to see whats up with it. and they say it will be about 1000 bucks to fix it. she for some reason has no print out of what they were going to do. she took it to local mechanic we have used for years. charges 301 dollars to what he says is a basic tune up. was able to get the yellow maitnece light off and says no, spark plugs are no problem. then a few days later light is back on, says bring it in. now he says oh yes, it is the spark plugs. wrong spark plugs and they should have never have been installed. very bad! $138.00 for install of 4 new toyota brand spark plugs. well guess what, now its a few days later again and YELLOW MAITNENCE LIGHT is back on. so any of you out there who may have the slightest clue even, please....inform me. it would be much appreciated.
Okay, so it was around the end of january when my sister ended up calling home saying car pooped out on freeway. i go and see if i can get it going. i cant.
car gets towed to house. im wondering what it could be. since car turns over. 2 times the car has not started in the past and i had to jump it. finally we got a new battery through toyota. so i knew it wasn't that. in the morning my grandma is asking well now what the hell are we going to do. i have a friend of a friend who is one of those all around do it yourself guys. but he mainly is into cars, racing, etc. i have seen him do many miracles, tricks and what not on old chevys and fords. so im keeping him in the back of my head. i then go out to car again to try and get it going thats when i find the reciet that states $10.22 was filled into car last night. and oh my gosh, what does it say? diesel fuel. almost 5 gallons total. so i call toyota to see what they could do. im debating if i should state that there is diesel fuel in car. well i told them and they say that well that voids the warranty, at least for that repair. so basically $90+ an hour for mechanic. and all these other things he is naming off they would have to do. looking over 5 or $600. okay, no way. thats when i call that guy. he comes over, taste fuel says oh yeah its diesel. we empty all the fuel into a 5 gallon bucket. goes right to the very top. im thinking cool, lets fill it and were done. he says no, spark plugs may be shot. now keep in mind i dont know too much about mechanics of cars. he looks at them says i can try cleaning them i think he said, but then decided no, lets get new ones. there cheap. so we get AUTOLITE Part # XP3924. now we fill with premium fuel. try starting and nothing. he then says lets go back to auto zone. we buy a can of ether. im getting a bit worried, becuase i know my grandma is used to the "normal" or whats normal to her. taking to toyota and paying bucks and thats it. anyway. spraying ether into if i remember correctly the air filter or vent, something like that. intake i forget honestly. that gets it going. something else while thats being done is someone else has the fuel line going to the engine unplugged and is holding it and letting that fuel go into a 1 gallon empty thing of oil. thats when he was pretty certain all the diesel was out of it. car had lots of white smoke coming from the exhaust, it was a bit funny feeling and shaking. but after drive around block a couple times. it was perfect. now is when i notice maitnece light on. engine light or the oil light was already on. i ask him whats up. says its probably because there not toyota plugs in. 2 weeks later grandma decides to take it to toyota to see whats up with it. and they say it will be about 1000 bucks to fix it. she for some reason has no print out of what they were going to do. she took it to local mechanic we have used for years. charges 301 dollars to what he says is a basic tune up. was able to get the yellow maitnece light off and says no, spark plugs are no problem. then a few days later light is back on, says bring it in. now he says oh yes, it is the spark plugs. wrong spark plugs and they should have never have been installed. very bad! $138.00 for install of 4 new toyota brand spark plugs. well guess what, now its a few days later again and YELLOW MAITNENCE LIGHT is back on. so any of you out there who may have the slightest clue even, please....inform me. it would be much appreciated.
MAINTENANCE LIGHT is on? or is the Check Engine light on?
$301 for a basic tune-up at 22k miles? and $138 to change out spark plugs? Sounds like you need a new mechanic. Should of just paid Toyota, you're pretty much halfway there.
$301 for a basic tune-up at 22k miles? and $138 to change out spark plugs? Sounds like you need a new mechanic. Should of just paid Toyota, you're pretty much halfway there.
301 for tuneup is half true. he also put 2 new yokohama tires on $ 159Originally Posted by FunctionSpec ↑MAINTENANCE LIGHT is on? or is the Check Engine light on?
$301 for a basic tune-up at 22k miles? and $138 to change out spark plugs? Sounds like you need a new mechanic. Should of just paid Toyota, you're pretty much halfway there.
its WARRANTY so id take it to dealer......Originally Posted by la_scanner ↑around 21, 22,000 miles on vehicle.
Dealer won't pay a warranty claim because the owner put diesel fuel in a gasoline engine.
However, if you neglect to mention that and just take it in and say "hey, this light came on"... they may find and fix the problem under warranty. (and I agree, it's likely either a fouled catalytic convertor or a fouled O2 sensor caused by trying to burn diesel). I wouldn't take it to the same Toyota dealer that you called and talked to about putting diesel fuel in the tank, though.
Or, you could man up, get your sister to man up, and split the cost of the repair with her. You'd be $300 poorer and DONE with this issue already had you done that. Instead, you're out almost $300 anyway, and still dealing with it.
However, if you neglect to mention that and just take it in and say "hey, this light came on"... they may find and fix the problem under warranty. (and I agree, it's likely either a fouled catalytic convertor or a fouled O2 sensor caused by trying to burn diesel). I wouldn't take it to the same Toyota dealer that you called and talked to about putting diesel fuel in the tank, though.
Or, you could man up, get your sister to man up, and split the cost of the repair with her. You'd be $300 poorer and DONE with this issue already had you done that. Instead, you're out almost $300 anyway, and still dealing with it.
Speaking from experience as a automotive technician. When the computer sets a code P0420 it is comparing the wavelength of the front o2 sensor compared to the rear o2 sensor. When they are simular it detects catalist problems. The most likely cause is your catalic converter isnt operating anymore. Another less likely cause is the o2 sensor heater circuit is defective. But usually this will trigger a o2 sensor code for that. So basically in the morning when the engine is cold the o2 dosnt rapidly heat up and is relying on exhaust gases. One way to test this is disconect the 02 sensors. There should be 4 wires 2 of them the same color usually black. Connect a ohm meter between those 2 wires and you should measure resistance. Usually 12-18 somewhere in that range depending on the temperature. If you measure open loop it means the heater circuit is burnt open. And the 02 needs to be replaced.
If the 02s test okay. You need to be looking at the cat. 2 ways really to test it. One is to get a rubber mallet and tap on the catalitic converter. If you hear rattling like it sounds like tehrs rocks in it. The cat is definately bad. Another way is to get a pyrometer and measure the inlet cat exhaust temp and the outlet cat exhaust temp. The readings after the cat should be hotter. Usually about 100 degrees. If exhaust gas is going in the job of the cat is to flash burn any gasoline that hasnt been fully burn int he combustion chamber. So ofcourse the exhast gas is going to be hotter as it passes through the cat. If the exhaust gas is the same or even cooler. That tells you the cat is doing squat. So it is defective.
If you find out the cat is bad. You now need to trace down the cause. I would suggest looking at your spark plugs. To damage a cat you need to have an excessively rich mixture or incomplete combustion. Otherwise you will have the same problem again.
If the 02s test okay. You need to be looking at the cat. 2 ways really to test it. One is to get a rubber mallet and tap on the catalitic converter. If you hear rattling like it sounds like tehrs rocks in it. The cat is definately bad. Another way is to get a pyrometer and measure the inlet cat exhaust temp and the outlet cat exhaust temp. The readings after the cat should be hotter. Usually about 100 degrees. If exhaust gas is going in the job of the cat is to flash burn any gasoline that hasnt been fully burn int he combustion chamber. So ofcourse the exhast gas is going to be hotter as it passes through the cat. If the exhaust gas is the same or even cooler. That tells you the cat is doing squat. So it is defective.
If you find out the cat is bad. You now need to trace down the cause. I would suggest looking at your spark plugs. To damage a cat you need to have an excessively rich mixture or incomplete combustion. Otherwise you will have the same problem again.
okay. i am uploading a youtube video of my grandmother on phone with mechanic. i had called him a half hour before she did. he told me his computer never showed P0420. Since i do not know how to explain what he is talking about. i figured why not listen to it yourself. i should have ready in 10 min.
lmao swap the coils?
there are misfire codes that pertain to the specific cylinders (1 through 4) swapping the coils will not make the cat or the 02 sensor work differently.
there are misfire codes that pertain to the specific cylinders (1 through 4) swapping the coils will not make the cat or the 02 sensor work differently.
I forgot to add i did call him about a half hour b4 my grandma did and he was saying something about another code that was on for him. i couldn't understand him. but when i told him what im getting off my reader, it's like as if he didn't want to talk about it. maybe im over analyzing this. i can't wait for all the shit from some on here telling me its illegal to record calls. i know, i know. i don't like seeing my grandma get took either.Originally Posted by Shroomster ↑lmao swap the coils?
there are misfire codes that pertain to the specific cylinders (1 through 4) swapping the coils will not make the cat or the 02 sensor work differently.
PLEASE don't take this the wrong way:Originally Posted by la_scanner ↑I forgot to add i did call him about a half hour b4 my grandma did and he was saying something about another code that was on for him. i couldn't understand him. but when i told him what im getting off my reader, it's like as if he didn't want to talk about it. maybe im over analyzing this. i can't wait for all the shit from some on here telling me its illegal to record calls. i know, i know. i don't like seeing my grandma get took either.
TAKE IT TO THE DEALER AND ASK THEM IF THEY CAN DIAGNOSE IT. BUT ASK THEM IF IT WILL BE UNDER WARRANTY FIRST AND FOREMOST.
That is the best thing to do. period end of story... guy is obviously not a very 'skilled' mechanic or conveyor of his intentions/ideas. if he doesn't want to talk about the problems directly then walk away.
take this the wrong way? ABSOLUTELY NOT! this is exactly the type of thing im looking for. its very much appreciated too. i really hope no one thinks im trying to waste anyone's time on this forum.Originally Posted by Shroomster ↑PLEASE don't take this the wrong way:
TAKE IT TO THE DEALER AND ASK THEM IF THEY CAN DIAGNOSE IT. BUT ASK THEM IF IT WILL BE UNDER WARRANTY FIRST AND FOREMOST.
That is the best thing to do. period end of story... guy is obviously not a very 'skilled' mechanic or conveyor of his intentions/ideas. if he doesn't want to talk about the problems directly then walk away.
no, I think you're just trying to get to the bottom of this with the help of the forum (albeit limited help as we don't have access to the car)
if you do go to the dealer try to see if they can waive the diagnostic fee. plead your case they may be sympathetic.....
if you do go to the dealer try to see if they can waive the diagnostic fee. plead your case they may be sympathetic.....
if they didnt know about the deisel incident, then I would assume your dealer would see that the cat(s) were gummed up or something similar, and replace under warantee without second thought.
just want to let everyone know that toyota is waiting on the catalytic converter to arrive. then they will replace. under warranty. everyone's happy again. yay!
-Jameson
-Jameson
👍
👍Originally Posted by cali yaris ↑👍
I have the P0420 as well, is it best to have Toyota handle this one, or would any garage be able to troubleshoot this right the first time? I have reset mine it comes on the next time I fire up the car in the first 4 minutes of driving when it has sat for any length of time.
I have the 420 on too. Would first like to try resetting it. How do you do this?
FYI that's $28 + a $4 tool if you DIY.Originally Posted by la_scannerspark plugs and charges $138.00