Yarisworld Archive

Power Lock button??

26 posts · 19,600 views

cyberfroggOriginal postTX · Mar 25, 2009#1
Ok, so I got my car used. And it was advertised to have the power package. Power locks, windows... But when I saw it, it didnt. So we had the power windows installed with the switches and later on we got power locks.


But they only lock and unlock with this:


Now, I saw that I have these two in the middle:


One's going to be for the fogs and I was wondering if there was ANY way I could add a lock/unlock switch in there. Its very annoying to have to look through my keys to unlock the door for someone from the inside... Any help would be much appreciated! thanks.

Replies 25

enobmort42Denver, CO · Mar 25, 2009#2
I installed my aftermarket power locks and wired them to my Python alarm. They only power lock/unlock with the remote, too. I'm wondering the same thing: if it's as simple as throwing an inline switch in there somewhere?
CTScottUSA, CT · Mar 25, 2009#3
Look at the installation manual for your remote entry manual. Look for the lock and unlock outputs. You will either need to ground the output through a switch, or pull it high (the manual will show if the outputs are positive or negative.)

I was going to point you to the keyless entry lock/unlock wires in the driver's kick panel, but then realized that your cars started with manual locks, so those wires are probably not used.
b_hickman11Tyler, TX · Mar 25, 2009#4
Your door actuators are probably only 2-wire when they should be 5-wire so that all doors will Lock/Unlock when you flip any lock on any door.
enobmort42Denver, CO · Mar 25, 2009#5
Originally Posted by b_hickman11 ↑
Your door actuators are probably only 2-wire when they should be 5-wire so that all doors will Lock/Unlock when you flip any lock on any door.
i didn't know about that feature! lol
ShroomsterOrlando · Mar 26, 2009#6
those two dead spots...one of them is actually where the o.e.m switch goes....
b_hickman11Tyler, TX · Mar 26, 2009#7
Originally Posted by Shroomster ↑
those two dead spots...one of them is actually where the o.e.m switch goes....
No its not.....I have a Sedan with the power package and the OEM switches are on the doors.
CTScottUSA, CT · Mar 26, 2009#9
Originally Posted by b_hickman11 ↑
No its not.....I have a Sedan with the power package and the OEM switches are on the doors.
The liftbacks with the power package have a switch there (part number 84930-52050). It's a two way lock/unlock toggle and it's about $60 from Toyota).
b_hickman11Tyler, TX · Mar 26, 2009#10
Originally Posted by CTScott ↑
The liftbacks with the power package have a switch there (part number 84930-52050). It's a two way lock/unlock toggle and it's about $60 from Toyota).
This is true....but he has a Sedan
CTScottUSA, CT · Mar 26, 2009#11
Originally Posted by b_hickman11 ↑
This is true....but he has a Sedan
Correct, but he's looking for an easy solution to add a lock/unlock switch to a non-oem system. It seems to me that using the liftback switch in the center console would be easier / less expensive than adding the OEM sedan door switch module.
cyberfroggThread starterTX · Mar 26, 2009#12
yeah. I don't want to add the whole door switch, I'd rather just use the one in the middle.. Would it have been easier with the 5 wire actuator? =/
CTScottUSA, CT · Mar 26, 2009#13
Originally Posted by cyberfrogg ↑
yeah. I don't want to add the whole door switch, I'd rather just use the one in the middle.. Would it have been easier with the 5 wire actuator? =/
With the 5 wire actuators, you wouldn't have needed to add a switch, as unlocking the manual door lock on the driver's door would have unlocked all of the other doors as well.

Do you know what brand/model your keyless system is?
cyberfroggThread starterTX · Mar 26, 2009#14
xD duh thats true... lol oops. Ah well my mom took the car. I'll check what it is later.. I remember it was K-9 or something like that. I'll check it out when she gets home..
CTScottUSA, CT · Mar 26, 2009#15
Originally Posted by cyberfrogg ↑
xD duh thats true... lol oops. Ah well my mom took the car. I'll check what it is later.. I remember it was K-9 or something like that. I'll check it out when she gets home..
Yeah, K-9 Mundial SS (I should have recognized that from the remote).

In the image below, look at the three pin connector with the Green (-Lock), Red, and Blue (-Unlock) wires.

Tap onto the green and blue wires as they leave the module. Run a wire from green to one side of your lock switch and ground the other side. Do the same for blue with your unlock switch.

cyberfroggThread starterTX · Mar 26, 2009#16
woah seriously? Is that all I need to do? I guess now all I need is a lock/unlock switch that will fit in that hole in the middle... Do you know where I can get something like that? thank you thank you thank you! lol 😁
CTScottUSA, CT · Mar 26, 2009#17
Yeah, that's it.

For switches, the slickest one would be the liftback one I mentioned above, as it would fit perfectly in one of the slots and would even have the lock/unlock labeling to it.

If you want to save cash, you could just use two momentary normally open switches from Radioshack (for under $4 each). You could find two that will fit together in one of the knockouts.
cyberfroggThread starterTX · Mar 26, 2009#18
sweet. =] Are you sure radioshack has em though? anddd I was wondering if I could get the liftback switch at a dealership or something.. And if I could, do you know what the part number would be? thanks so much for all your help! 👍
CTScottUSA, CT · Mar 26, 2009#19
Originally Posted by cyberfrogg ↑
sweet. =] Are you sure radioshack has em though? anddd I was wondering if I could get the liftback switch at a dealership or something.. And if I could, do you know what the part number would be? thanks so much for all your help! 👍
From Radioshack, you could use any normally open push button momentary switch Like this for example (for $2.69 each):

Picture lost · rsk.imageg.net

http://www.radioshack.com/product/in...ductId=2062501


The OEM Liftback one is Toyota Part Number: 84930-52050
You could definitely order it from any Toyota parts department or TRDSparks.com

Looks like the one in this picture:

Picture lost · img237.imageshack.us
cyberfroggThread starterTX · Mar 26, 2009#20
Awesome!! Wooh!! thanks so much! :D

holy smokes! I just saw the switch is like 47 bucks!

ahh I guess I'll go with the momentary switch.. still, I'll have a designated lock/unlock button! lol thanks. =]
CTScottUSA, CT · Mar 26, 2009#22
No good on those three. They need to be momentary, rather than latching (spring back, not click).

Ideally, you want a single momentary-off-momentary switch. Check these two out from Digikey (A real electronics supply place).

This one is $7 and looks like it might just fit in one of the holes:

http://search.digikey.com/scripts/Dk...me=679-1182-ND





Here's an illuminated one for $18 (hole would have to be lengthened by ~3mm):
http://search.digikey.com/scripts/Dk...me=480-2163-ND

cyberfroggThread starterTX · Mar 26, 2009#23
Oh I see. I like those better. lol Just out of curiosity, would it be possible to go to a junkyard and take off a lock switch of an older toyota?
CTScottUSA, CT · Mar 26, 2009#24
Maybe. Nothing but Yaris Liftbacks used that particular part number, so you'd be looking for something that would fit in the knockout. I have no idea if any other Toyotas used a similar switch.
cyberfroggThread starterTX · Mar 26, 2009#25
alright cool thanks. =] I'll go look for one in a junkyard and try it out and if it doesn't work, I'll get the one you suggested. thanks. :D I'll post pics when I'm done.
ShroomsterOrlando · Mar 26, 2009#26
good luck! :D