Yarisworld Archive

N/A?

33 posts · 7,588 views

YodaOriginal postFL · Mar 23, 2009#1
Are there anymore options for N/A power? i did the I/H/E(Axleback) &Pulley.I am sitting on about $300 with nothing to gear it toward😕

Replies 32

hatchbackkid82. · Mar 23, 2009#2
1ZZ-FE throttle body. I think they go for $60, at least that's what i got mine for. Also you may want to get the Nitto mid-pipe, it would complement the axle back real nicely. Should see a lil' more power with those two mods and what you have
YodaThread starterFL · Mar 23, 2009#3
did you notice a power increase or just a lost of tq down low? think i might drive 2hours to get my car dyno today after i get off work at 2pm
LorenSafety Harbor, FL · Mar 23, 2009#4
How do you drive your car? There's probably some more top end power to be gained by replacing the exhaust between the header and axle, but it's probably only going to show up above 5500-6000 rpm. In the real world, that just translates to numbers. "My car makes 100 whp on the dyno". Big deal. Unless you're drag racing, mid-range torque and throttle response is far more important.

If you're looking for more "daily driving" torque, about the only thing left to do is a lightweight flywheel and start shaving weight from the car.
SabretoothSt Cloud FL · Mar 23, 2009#5
Trust me, removing rear seats and getting rid of useless junk from the rear, definatly makes the car feel faster.

In my case, I removed nearly 100lbs from the back because of my 60/40 split seats.
Saved maybe 6 lbs total by replacing the front seats with racing seats.
It all adds up.
hatchbackkid82. · Mar 23, 2009#6
Exactly👍. Removing things like seats, carpet, sound insulation will make a difference. it won't necessarily make horsepower... the engine doesn't have to work as hard to get the car moving since your reducing it's mass

Originally Posted by Sabretooth ↑
Trust me, removing rear seats and getting rid of useless junk from the rear, definatly makes the car feel faster.

In my case, I removed nearly 100lbs from the back because of my 60/40 split seats.
Saved maybe 6 lbs total by replacing the front seats with racing seats.
It all adds up.
hatchbackkid82. · Mar 23, 2009#8
Exactly
YodaThread starterFL · Mar 23, 2009#9
Originally Posted by Loren ↑
How do you drive your car? There's probably some more top end power to be gained by replacing the exhaust between the header and axle, but it's probably only going to show up above 5500-6000 rpm. In the real world, that just translates to numbers. "My car makes 100 whp on the dyno". Big deal. Unless you're drag racing, mid-range torque and throttle response is far more important.

If you're looking for more "daily driving" torque, about the only thing left to do is a lightweight flywheel and start shaving weight from the car.
i drive my car as if it were fast... i use to drive a 00 Si after all so i am rev happy Soo you sayin i would need a mid pipe? do they make one for SD? Removing the seats are not practical for me tho i like the idea. Just looking to make some N/A power before i go FI a couple months later
LorenSafety Harbor, FL · Mar 23, 2009#10
If your plan is to go FI, why not be patient and spend your $300 on something like a wideband O2 sensor rather than on something that might maybe net you 3 hp for a couple months?
YodaThread starterFL · Mar 23, 2009#11
.... you are right. Lets change that months to a year+ later lol
CASTREXCosta Rica · Mar 23, 2009#12
No need to go drastic on the weight shaving area...

Taking the rear seat out and installing them out is a matter of 15 min.

Is not like you won't be able to seat anyone on the back of your car ever again... 😁

I've taken mine in and out about 3 times now. If I know I won't be carriying anyone for a while I just take them out. Is really easy.

If you have the 60/40 rear seats... those are REALLY heavy!

When I go out for a spirited drive I even take out the spare tire and jack (If I'm not going too far away from home 😳)

You can definetely feel the difference....

When I remove the back seat and spare tire I have to adjust the rear coilovers as the car will raise the back like 1/2 or more...

😈
harveyjaiSydney, Australia · Mar 23, 2009#13
"I drive my yaris like i had stole it!"LOL

If you install the 1ZZ-FE throttle body,
do u need a piggy back or any ECU changes???
hatchbackkid82. · Mar 23, 2009#14
Nope after installing it just let the car idle for a little bit and it should re-learn the new throttle body. This is the case if you swpped over the chip that's in the TB as well. Really cheap mod $60 shipped. Hopefully you can find one for that cheap. don't know how much they go for on ebay
jt258HOUSTON · Mar 23, 2009#15
HOW MUCH OF A DIFFERENCE IN SIZE ARE THERE BETWEEN THE 1NZ &1ZZ THROTTLE BODIES. HOW MUCH POWER DIFFERENCE CAN BE SEEN?
AlexNet0Rockland, ME · Mar 23, 2009#16
dont yell, we can all hear you. 🙂

I think its almost a 1" difference, I have it but I havent measured it.
harveyjaiSydney, Australia · Mar 24, 2009#17
1inch of a difference?!=.=
YarisPRMayaWest, Puerto Rico · Mar 24, 2009#18
Originally Posted by AlexNet0 ↑
dont yell, we can all hear you. 🙂

I think its almost a 1" difference, I have it but I havent measured it.
I have it installed and I did measure it
Stock 1.5
1ZZ 2.5

I have some pics but I' am not uploading them just to see that's 1" bigger
xen555Puerto Rico · Mar 24, 2009#19
Originally Posted by YarisPR ↑
I have it installed and I did measure it
Stock 1.5
1ZZ 2.5

I have some pics but I' am not uploading them just to see that's 1" bigger
y sentiste alguna diferencia? vale la pena hacerlo?
YodaThread starterFL · Mar 25, 2009#20
thx for all the feedback. Was the installation hard? do i need some more parts and tubing? My main thing is did you lose tq anywhere in the power band...
YarisPRMayaWest, Puerto Rico · Mar 25, 2009#21
Originally Posted by xen555 ↑
y sentiste alguna diferencia? vale la pena hacerlo?

Hace algo, pero mano no hace maravillas. Yo lo consegui ene un junker. El problema de estos carros es q simplemente no corren jajajaj.



Saludos
hatchbackkid82. · Mar 25, 2009#22
I felt the lowend suffered a lil bit. But midrange and topend is great

Originally Posted by Yoda ↑
thx for all the feedback. Was the installation hard? do i need some more parts and tubing? My main thing is did you lose tq anywhere in the power band...
YodaThread starterFL · Mar 25, 2009#23
ahhhhhh ok kewl gonna order it today when i get off work. where can i get a good deal? o and i want to dyno my car tomorrow anyone know of a good place in florida got like $150 to spend on it lol
hatchbackkid82. · Mar 26, 2009#24
Just get ready for CEL👎 Hopefully your one of the lucky ones that doesn't get one.

Originally Posted by Yoda ↑
ahhhhhh ok kewl gonna order it today when i get off work. where can i get a good deal? o and i want to dyno my car tomorrow anyone know of a good place in florida got like $150 to spend on it lol
YarisPRMayaWest, Puerto Rico · Mar 26, 2009#25
Originally Posted by hatchbackkid82 ↑
Just get ready for CEL👎 Hopefully your one of the lucky ones that doesn't get one.
I get a CEL 2 days and no No CEL a week and so goes on so it doesn't bother me
hatchbackkid82. · Mar 27, 2009#26
I hate CEL's😠 I love the the slight increse in power but hate seeing that lil' orange light on. This would be a great mod if there was some way to keep that check engine light off...already did the chip swap
xen555Puerto Rico · Mar 29, 2009#27
Originally Posted by YarisPR ↑
Hace algo, pero mano no hace maravillas. Yo lo consegui ene un junker. El problema de estos carros es q simplemente no corren jajajaj.



Saludos
Y ES VERDAD DE CUANDO CALIENTAN SUBE MUCHO LAS REVOLUCIONES?
YarisPRMayaWest, Puerto Rico · Apr 1, 2009#28
Originally Posted by xen555 ↑
Y ES VERDAD DE CUANDO CALIENTAN SUBE MUCHO LAS REVOLUCIONES?

Cuando lo prendes sube las revs a 3000 desps baja normal
hatchbackkid82. · Apr 1, 2009#29
Pero posiblemente te va iluminar la luz de Check engine. Asi me paso a mi por eso vendi el TB. Ize todo lo dice el DIY y siempre ilumino las luz
anonymous userwindward oahu · Apr 2, 2009#30
In a N/A application, large changes of HP can be made with fluid changes. Look into that, I gained 15 WHP with a simple fluid change, not on the yaris mind you, but it could'nt hurt. (hint?-Redline)
Bluevitz-rsOshawa, Ontario, Canada · Apr 5, 2009#31
So with the Throttle body upgrade, what intake fits on that. I already have the factory AEM.
yarstarGeorgia · Apr 5, 2009#32
Originally Posted by Bluevitz-rs ↑
So with the Throttle body upgrade, what intake fits on that. I already have the factory AEM.

I got the AEM CAI and it fits with no problem.

This really makes a big difference, but you do get CELs.

You can find them on Ebay for @ $50.
RagnaCaTVillalba, Puerto Rico · Apr 5, 2009#33
Originally Posted by Loren ↑
How do you drive your car? There's probably some more top end power to be gained by replacing the exhaust between the header and axle, but it's probably only going to show up above 5500-6000 rpm. In the real world, that just translates to numbers. "My car makes 100 whp on the dyno". Big deal. Unless you're drag racing, mid-range torque and throttle response is far more important.

If you're looking for more "daily driving" torque, about the only thing left to do is a lightweight flywheel and start shaving weight from the car.
Hey Loren I live in PR and it's full of hill's is Aluminum Flywheel is a good idea for pulling out in hill, I heard also the I have to REV alot more.