Yarisworld Archive

HOW CAN I KEEP FOGHLIGHS ON WITH HIGH BEAM?

28 posts · 17,015 views

derickveliz2Original postCentral, MA · Mar 18, 2009#1
How can I keep foglihgs on when using high beam? the fog lighs turn off when I switch to high beam.

There is any way I could keep them on?

Thank you.

Replies 27

BLAZINBLUEVITZNEW YORK · Mar 18, 2009#2
mine is on a seperate switch so its on til i turn them off.....
rningonfumesSoCal · Mar 18, 2009#3
http://www.toyotanation.com/forum/sh...ight+high+beam

From what I read, it's possible. The relay gets a signal from the low beams to tell it to send power to the fogs. If you can jump the signal to hook up to the high beams as well as the low beams, you might be able to just keep them on.

Homework for you is to find out how the relay is hooked up to the low beam, find the high beams and hook the two up.
1NZYaris1New Zealand · Mar 18, 2009#4
Originally Posted by rningonfumes ↑
http://www.toyotanation.com/forum/sh...ight+high+beam

From what I read, it's possible. The relay gets a signal from the low beams to tell it to send power to the fogs. If you can jump the signal to hook up to the high beams as well as the low beams, you might be able to just keep them on.

Homework for you is to find out how the relay is hooked up to the low beam, find the high beams and hook the two up.
If you are useing the factory combo stalk , for get about it .
but if you are useing the aftermarket set up installed into factory wiring it's quite easy , you need to remove one wire , do you have any photos of your instal (wire colors ) and where you wired them .
👍
rningonfumesSoCal · Mar 18, 2009#5
I'm going to school but I'll do a more indepth search later. As for me, haven't done the install, I haven't found the time to do it.

There is a way, I'm quite sure of it. Just like many folks much smarter than I have figured out how to disable Daytime running lights and the seat belt chime, I know others have done it to their factory fog lights (vs aftermarket like that of Blazinbluevitz has). It just might not be our cars but a different model and I'm depending on Toyota to have similar electrical work in all their cars.
firebobon the road · Mar 18, 2009#6
It is illegal in most states to run your high beams and fog lights at the same time. You’re only allowed to produce so much light out of the front of your car. The people that have the high end lights and running your fog lights can break the limit. If you blind an oncoming driver and they hit you if they can prove you broke the law then it will now be your fault.

Running your high beams and low beams at the same time could also get you over the limit. I know this was done in the older cars a lot. In some states the HID lights are just under the limit on there low beams; toss on your fog lights and now you’re over. Every state is different and might be a PITA to find out what the legal limits are for your state.

I know this first hand because I hit someone head-on whale driving on a redneck back road. It was a combined speed of 30 / 35 mph. My wife and I were both blinded by there lights and upon inspection of there car found 2 sets of fog lights and there low beams were on. We took pics and had it written in the report. After it was all cleared up we went to the police station and made them open an investigation (3:15 AM) to find out what bulbs were in the sockets. Once at court I asked to talk before any info could be given about the wreck and provided this info with a copy of the law. The ladies lawyer dropped his jaw as the gabble hit the table before the lawyer could say anything to the judge.
1NZYaris1New Zealand · Mar 18, 2009#7
Originally Posted by rningonfumes ↑
I'm going to school but I'll do a more indepth search later. As for me, haven't done the install, I haven't found the time to do it.

There is a way, I'm quite sure of it. Just like many folks much smarter than I have figured out how to disable Daytime running lights and the seat belt chime, I know others have done it to their factory fog lights (vs aftermarket like that of Blazinbluevitz has). It just might not be our cars but a different model and I'm depending on Toyota to have similar electrical work in all their cars.
It is possable to do and very easy , but as stated , it could be illegal in your state .👍
Klink10910 · Mar 18, 2009#8
With the factory stalk I would just like to be able to run fogs only.
YAR1SRaleigh, NC · Mar 18, 2009#9
If you only wanted to do it momentarily you could push the stalk halfway... this turns on highbeams and leaves fogs on at same time... you have to hold it there in place though.. I do this sometimes when i see people walking in my neighbourhood at night. You'll feel the click and see the high beams come on, not very practical but it can be just as long as you can hold it in place whilst driving.
1NZYaris1New Zealand · Mar 18, 2009#10
Originally Posted by Klink10 ↑
With the factory stalk I would just like to be able to run fogs only.
The fogs turn off because the relay got the signal from the high beam ,
if your wheren't useing the factory stalk stopping this is real easy ,
but with the factory stalk you would need to experiment a little ,
start by looking at the wires on the back of the relay .
for pins means there will be at least 4 wires hopefully 5 or 6
or you could sit down for a couple of hours and read the service manual
for the wireing diagram. to find the wire you need to disconnect.

Just remembered ,check the back of the relay look for a white wire with black line .
99% sure that is the wire you need to disconnect.
churpTropical Minnesota · Mar 19, 2009#11
I installed aftermarket driving lights and hooked the relay signal contact to the park lights....this way they are on anytime headlights or park lights are on.
Klink10910 · Mar 19, 2009#12
1NZYaris....thanks. When it comes to electrical I can follow a DIY with pics. If however it becomes try it yourself I am in left field. I've been hoping someone would eventually do this. I'll continue to wait.
eTiMaGoBangkok, Thailand · Mar 19, 2009#13
Looking through the electrical diagrams trying to figure it out... I'm interested, as I have dealer-installed aftermarket front fogs, and the cars here come with rear fogs stock...

It's pretty easy in theory, just need to swap a wire so that the fog light switch is energized when the parking lights are on (which they are in both high and low beam)

So here's what you'd need to do (in theory, someone please test this first with some spare fuses handy 😆):

headlightswitch.gif

Pin 4 is the input from the low beams and/or DRL module, pin 13 is the output from the parking lights.

Essentially you want to cut the wires going into pin 4 (depending if you have DRLs, there may be two wires, I'm not so sure), then short pin 4 to pin 13.

Give it a try!
CTScottUSA, CT · Mar 19, 2009#14
Originally Posted by eTiMaGo ↑
Looking through the electrical diagrams trying to figure it out... I'm interested, as I have dealer-installed aftermarket front fogs, and the cars here come with rear fogs stock...

It's pretty easy in theory, just need to swap a wire so that the fog light switch is energized when the parking lights are on (which they are in both high and low beam)

So here's what you'd need to do (in theory, someone please test this first with some spare fuses handy 😆):

Attachment 20549

Pin 4 is the input from the low beams and/or DRL module, pin 13 is the output from the parking lights.

Essentially you want to cut the wires going into pin 4 (depending if you have DRLs, there may be two wires, I'm not so sure), then short pin 4 to pin 13.

Give it a try!


I think you would want to use pin 10 (T1) rather than 13 (B1). B1 is the non switched leg, so the fogs would always have power. T1 is the switched output from the parking light switch.
eTiMaGoBangkok, Thailand · Mar 19, 2009#15
sure about that? look at the lighting.pdf, page 75, the ground line is T1, or am I not understanding correctly?
CTScottUSA, CT · Mar 19, 2009#16
Originally Posted by eTiMaGo ↑
sure about that? look at the lighting.pdf, page 75, the ground line is T1, or am I not understanding correctly?
The switch switches the ground side. The difference between T1 and B1 is which side of the switch you are on.
1NZYaris1New Zealand · Mar 19, 2009#17
Originally Posted by eTiMaGo ↑
sure about that? look at the lighting.pdf, page 75, the ground line is T1, or am I not understanding correctly?
i Currently have my fogs running from pin 3 only, i did not use pin 4
as all the diy's say , for my aftermarket switch .
So what you are saying for the factory switch makes a lot of sense .
Because all you are trying to do is stop the high beam signal from
getting to fog light relay. 👏 👏 👏 👏 👏🙇🙇🙇🙇
rningonfumesSoCal · Mar 19, 2009#18
Who ever does this first..ie can take pics with install, please make a quick DIY and sticky it!
MarfulionFlorida · Mar 19, 2009#19
if you pull the high beam lever just a little bit before it locks on, then the highbeams will come on at the same time as the low beams and foglights, off course you have to hold it at that position with your hand.
cm07yarisAppleton, WI · Mar 20, 2009#20
I have been having trouble with my foglights lately using the factory stalk and I finally got the supposed "correct" relay which is 90080-80726 I believe. Now my fogs only turn on when the highbeams are on and will stay on when they are switched off. However, they still will not turn on when I have my lowbeams switched on. Guess I just have to switch on my highs quick just to get my fogs on because I've exhausted everything I can think of to get them working the way they should.
1NZYaris1New Zealand · Mar 20, 2009#21
Originally Posted by cm07yaris ↑
I have been having trouble with my foglights lately using the factory stalk and I finally got the supposed "correct" relay which is 90080-80726 I believe. Now my fogs only turn on when the highbeams are on and will stay on when they are switched off. However, they still will not turn on when I have my lowbeams switched on. Guess I just have to switch on my highs quick just to get my fogs on because I've exhausted everything I can think of to get them working the way they should.
Please talk to Garm it is diffently the incorrect relay , PLEASE.👍
window_leeCanada · Mar 20, 2009#22
easiest way is to ground the orange wire
eTiMaGoBangkok, Thailand · Mar 20, 2009#23
yes, certainly the easiest, but in that case the fogs could be on all the time, even with the key out of the car, so there's always a risk of forgetting them and draining the battery
derickveliz2Thread starterCentral, MA · Mar 25, 2009#24
Thanks everybody for you input.

I know in Massachusetts it's illegal to have more than 2 lights "on" facing forward (that is why I dislike people with their fog lights "on" when there is no fog)

My point is that I drive a lot in back roads late at night lots of woods around here with dears and all kind of animals and when I'm using high beam there is an area right in front of my car that I would like to have more vision.

My low beam illuminates that area very well but then I would like to see far away with my high beam.

That is way I would like to have high beam and fog lights at the same time.

Thanks again.
SailDesign. · Mar 25, 2009#25
I know that in England, (I grew up there) the foglights (i.e. below the bumper) can only be on with low beams or sidelights. Spotlights (above the bumper) can only be on with the high beams.
In the States? I guess anything goes, as long as there are no lights on the roof... I had a VW set up English-style, spots on with high beams, and never had a problem with the cops. Well, not because of lights, anyway. 🙂
firebobon the road · Mar 25, 2009#26
Most states let you run fog lights with your low beams and parking lights. But I think every state makes you cut them off with your high beams. There are laws that deal with how much light you can put out.
derickveliz2Thread starterCentral, MA · Mar 25, 2009#27
Originally Posted by firebob ↑
Most states let you run fog lights with your low beams and parking lights.
In Massachusetts only when bad weather.
firebobon the road · Mar 25, 2009#28
This is one of the reasons I do not do much to customize the stuff I drive. I end up driving in the 48 states and in Canada and there is no way to know what cop in what state is going to get you on what. I have not wanted fog lights but 2 times so far with my Yaris and I know a few states are picky with them.