1NZYaris1Original postNew Zealand · Mar 18, 2009#1This is to help those that would like to try it themselves 👍
enjoy and be careful.
Replies 49
Yaweshlong island · Mar 18, 2009#2they make it look so simple!
churpTropical Minnesota · Mar 19, 2009#3Good link, but removing wipers and associated cowl covers is not necessary.😉
YarisSedanCalifornia - Bay Area · Mar 19, 2009#4I did mine without removing the cowl or wiper blades
detroiterMetro Detroit · Mar 20, 2009#5Is it possible to do this without the spring compressor? and i'm curious as well, any negative effects to going with the lowering springs? Also, why would lowering springs cause you to need an alignment done since when the car comes stock from the factory without being driven much it doesn't need one?
TOUGEghostKauai · Mar 20, 2009#6You need the spring compressor to remove the stock front springs safely. If you are installing shorter aftermarket springs you should be able to install the new springs without using the compressor. No compressor is needed for the rear springs.
REMIrondequoit, NY · Mar 20, 2009#7Does anyone know how much I could expect to pay to rent a spring compressor?
I have been toying with the idea of lowering my Yaris, but the cost of install that I was quoted is more than I would want to spend. If I could do it myself lowering will be a much more feasible option, even if it took me all day to complete the job.
detroiterMetro Detroit · Mar 20, 2009#8I'd still like to know what the cons of using lowering springs are and also the reason for why one would need an alignment after installing them?
soloecho2Orono, Ontario · Mar 20, 2009#9Your car could bottom out over speed bumps that you could clear before. Stiffer ride the BOSS may not like. Front lip may become intimate with the odd parking curb. Toe in will be effected by the lower ride height.
detroiterMetro Detroit · Mar 20, 2009#10The toe will be affected by the lower ride height which is the reason for the alignment or it will always affect it?
texkidSugar Land, TX · Mar 20, 2009#11 Originally Posted by
detroiter ↑ The toe will be affected by the lower ride height which is the reason for the alignment or it will always affect it?
Look at it this way, as you stand your feet are closer together. Now as you crotch down, you spread your legs apart (changing the position of feet) to accommodate the change in stance. Well, when you lower/raise your car, the "stance" is different. Now the tires are sitting at a different angle to accommodate the new position. So you will need an alignment so that the tires will not wear out prematurely. It is only done at the time you change the springs.
detroiterMetro Detroit · Mar 20, 2009#12ahhh thank you for the insight. how does the tire place know what alignment to give it to make it right? I really don't know so i'm trying to learn
supmetSouthern California · Mar 20, 2009#13 Originally Posted by
detroiter ↑ ahhh thank you for the insight. how does the tire place know what alignment to give it to make it right? I really don't know so i'm trying to learn
they hang reflectors on your tires and shoot lasers at them. then a computer tells them which bolt to tighten and how much.
gwasabiHonolulu, Hawaii · Mar 20, 2009#14 Originally Posted by
REM ↑ Does anyone know how much I could expect to pay to rent a spring compressor?
I have been toying with the idea of lowering my Yaris, but the cost of install that I was quoted is more than I would want to spend. If I could do it myself lowering will be a much more feasible option, even if it took me all day to complete the job.
You can do it 808 Brokanic style. Use a C-clamp and Be REALLY REALLY CAREFUL with it. I mean REALLY REALLY careful. You get hit by one of those springs....man it'll leave a HUGE HUGE bruise. but yea......brokanic style use c clamps lol
and I think stock alignment on our car is 0 toe and 0 camber but don't quote me on that...
firebobon the road · Mar 20, 2009#15I have not done this on a newer car but…
I have used a ratchet strap to hold the coils of the spring where they were at. This will let you get them out since there compressed. Once out stick them under a different car and use it’s weight to let them back out.
If you try this use your brain. Use a few wraps on the springs. You just need the flat rope (webbing) not any of the metal stuff of the straps; to get the needed friction a clove hitch or two will hold it.
I did this with the springs off a 1 ton truck a few times.
detroiterMetro Detroit · Mar 21, 2009#16Does installing the springs void the 60k factory warranty?
And one last question is can you take the TRD lowering springs, install them then get an alignment and your done? Or do you need one of the lowering camber kits or something like that.
I was reading a story about someone who installed some eibachs I think it was and they had to order a specific camber kit or something so the shop could do a proper alignment because they could not do it without it. I'm kind of confused by that story of the person and then about how it says the TRD lowering springs does not change the vehicles suspension and handling geometry.
supmetSouthern California · Mar 21, 2009#17 Originally Posted by
detroiter ↑ Does installing the springs void the 60k factory warranty?
And one last question is can you take the TRD lowering springs, install them then get an alignment and your done? Or do you need one of the lowering camber kits or something like that.
I was reading a story about someone who installed some eibachs I think it was and they had to order a specific camber kit or something so the shop could do a proper alignment because they could not do it without it. I'm kind of confused by that story of the person and then about how it says the TRD lowering springs does not change the vehicles suspension and handling geometry.
You only need camber bolts if you want to change the camber. You don't
need to change the camber. It is optional, and mostly used for the track.
yarstarGeorgia · Mar 21, 2009#18 Originally Posted by
REM ↑ Does anyone know how much I could expect to pay to rent a spring compressor?
Autozone will lend you the tool for NOTHING. All you have to do is leave a deposit for them.
yarstarGeorgia · Mar 21, 2009#19 Originally Posted by
detroiter ↑ And one last question is can you take the TRD lowering springs, install them then get an alignment and your done?
This is exactly what I did. Put the TRDs on and got an alignment. Simple.
BTW. I just today installed Cusco GT-Zero Coilovers and did it the way the DIY here states by removing the wiper motor, etc.. IT WAS WAY EASIER THAN NOT REMOVING WHEN I PUT ON THE TRD LOWERING SPRINGS.
TRDs are now gonna be for sale. PM with bids if interested.
frownonfunRGV, Texas · Mar 30, 2009#20so if i'm installing new shocks and springs then do i just basically ignore the spring compressor part by setting that whole stock assembly aside and just add the new spring to the new shock and then bolt it all back in like the stock strut?
and what do i do with the back ones?
i did a quick search and didn't find any DIY specifically on shocks so i thought i'd ask before i just try and wing it.
marcustoronto, canada · May 29, 2009#21 Originally Posted by
YarisSedan ↑ I did mine without removing the cowl or wiper blades
im not sure how you did this..but maybe sedan is different..
1NZYaris1Thread starterNew Zealand · May 29, 2009#22i did my spring and shock install , earlier in the week , followed the Toyota
PDF to a T , the whole job took about 5 hour's .
that was by myself and taking my time , and taking photo's . 👍
jekqmbSTL · Dec 28, 2009#23Took us 3 hours, the rears took 15 minutes to install.....The front, we couldnt find the right tool to get those damn strut bolts out 🤷
We had to rig soemthing up with a socket and a allen key..What did you all use??? I didnt have an air gun so we couldnt spin them off really fast like most would have done?
YarisSedanCalifornia - Bay Area · Dec 28, 2009#24 Originally Posted by
marcus ↑ im not sure how you did this..but maybe sedan is different..
Picture lost · www.toolsource.com Its offset/swivels/and ratchets. Just put it over the nut and hold a alen key over the top of the center of the strut with a pipe on the end and turn.
jekqmbSTL · Dec 29, 2009#25Ya the new suspension tommorow we will be using an air gun 👍, those strut bolts will come right off this time....
justjesusOrange County · Dec 29, 2009#26aw man! that was a neat PDF. Today, I just lowered my friend's 91 Accord, and now I'm itching more than before to do mine. Cool deal on seeing this thread today -thanks guys
Hard_YarisEdmonton Alberta · Apr 1, 2010#27What about cutting the bump stops... is that necessary for all springs and shocks? OR are TRD's struts shocks, and springs manufactured so to not need to cut the bump stops? Like the guy did on the Tanabe install?
toy_torontoTarrana, Canada · May 15, 2010#28 Originally Posted by
Hard_Yaris ↑ What about cutting the bump stops... is that necessary for all springs and shocks? OR are TRD's struts shocks, and springs manufactured so to not need to cut the bump stops? Like the guy did on the Tanabe install?
Bump...
I'll either DIY mine or get someone else to do it but I'm looking to find out what the concensus is in terms of cutting (or not cutting) the bump stop -- is it necessary or only to be done with certain springs?
Which is the
RIGHT thing to do? 🤷
.
1NZYaris1Thread starterNew Zealand · May 15, 2010#29Cutting the Bump stops depends on the install 👍
toy_torontoTarrana, Canada · May 15, 2010#30😁 Thanks for the reply.
So for MY install, most likely I'll be using a set of Eibach ProKit (1" all around) and reusing the stock struts/bump stops...
Is the recommendation to cut, or to leave the bump stops as is for my particular install?
WeeYariGeorgetown, Ontario, Canada · May 15, 2010#31For a mild 1" drop leave the bump stops uncut. I'm down 1.5" and didn't bother cutting them.
toy_torontoTarrana, Canada · May 15, 2010#32Thanks WeeYari..
I'm just hoping I won't have to drive all the way to Kitchener to see thebarber to get my springs done 😉
rapev-8WI · Mar 24, 2011#33can someone explain to me how to do the front suspensions without removing the windshield cowl?
annnseattle · Mar 24, 2011#34👍
Originally Posted by
rapev-8 ↑ can someone explain to me how to do the front suspensions without removing the windshield cowl?
Why ? The cowl is super simple to remove. It may look hard but it's nothing and makes the job easy .
Klink10910 · Mar 24, 2011#35I agree with Annn. Removing also allows you to clean up the cowl real well. You would be surprised at what you can find in there, particularly if the vehicle is kept outside.
toy_torontoTarrana, Canada · Mar 25, 2011#36I spent the extra 10 minutes to remove the cowl, it made the job alot easier wit it out of the way.
rapev-8WI · Mar 25, 2011#37so i gotta remove the wiper arms when i remove the cowl??
toy_torontoTarrana, Canada · Mar 25, 2011#38why?harnett county NC · Jun 4, 2012#39 Originally Posted by TOLMACH ↑
I have a stupid question to everybody who knows the answer pls
Background: I plan swaping the stock shocks with blue Tokicos and retain the original springs
Step 14 and Step 19 of the manual above (see the link in the message by ToyToronto) show NUTS being placed in something that looks like a garbage bin. Does this mean I need to buy new nuts (the original ones must not be reused) . Later in the manual nut number apprears as 90179-12145.
Thanks
P.
I don't know the answer, but I believe the fastest way for you to find out is to call Micro Image @ (818) 610-3635. They always answer any questions you might have and will take as much time as needed for you to understand everything.
WeeYariGeorgetown, Ontario, Canada · Jun 4, 2012#40 Originally Posted by TOLMACH ↑
Step 14 and Step 19 of the manual above (see the link in the message by ToyToronto) show NUTS being placed in something that looks like a garbage bin. Does this mean I need to buy new nuts (the original ones must not be reused) . Later in the manual nut number apprears as 90179-12145.
Thanks
P.
I do not know of a single person, myself included, who has tossed out and replaced those nuts with new ones.
cali yarisCanoga Park, CA · Feb 22, 2013#41^ It's not necessary on the Yaris, if you look at how the top mounts work.
mahoutNC · Mar 19, 2013#42 Originally Posted by
1NZYaris1 ↑ This is to help those that would like to try it themselves 👍
enjoy and be careful.
Very good but one thing left out. They need to point out that the upper mounting nut is double. Removing the top nut is the removaql one to get the shock out. The shock assembly has a nut of its own. And it isn't necessary to remove the cover plastic or wipers.
spookybathtubCalifornia · Jan 19, 2015#43What is the last step (45) in that PDF?
ezhacker1San Francisco · Jan 19, 2015#44You mean: Wheel alignment and Head light adjusting?
zenN. Chas, SC · Feb 16, 2015#45Not sure what I'm doing wrong but I'm struggling to remove the top nut with my offset wrench and hex key in place 😠
jpmck03USA · Feb 19, 2015#46 Originally Posted by
zen ↑ Not sure what I'm doing wrong but I'm struggling to remove the top nut with my offset wrench and hex key in place 😠
If I recall, that was one of the tougher nuts to remove. Have you tried using a cheater bar?
spookybathtubCalifornia · Feb 20, 2015#47The torque on that nut is only 55Nm. I couldn't get it with a regular box wrench, but an offset made it easy. Rotate it so the hex key is pressed up against something, then you can get the nut loose.
komichalCZ · Jan 5, 2018#48Good PDF for reference. 🎉
I also like the video by KYB. Very understandable.
https://www.youtube.com/watch?v=0FEIDAFDnTA&t=436s I will most probably change the shocks in a few weeks. The springs are not cracked. Can they be "tired" so that it would make sense to change them too despite the fact that they seem intact?
My Yaris 2007 is still on the original shocks and springs and they are nearly gone according to the suspension diagnostic test.
komichalCZ · Jan 5, 2018#49To compress the springs you can easily get a
compressor worth 10 bucks. It will do the job nicely, not as fast as a professional electric compressor but it is safe comparing to any other home-invented mean of compressing the coils. Compressed coil is a grenade ready to explode.
azwad12Dhaka, Bangladesh · Jul 28, 2020#50Thanks!