Yarisworld Archive

16x7 +38mm front, 16x8 +0 rear WILL IT FIT?

28 posts · 8,890 views

wildmongoose26Original postDallas, TX · Mar 18, 2009#1
wanting new wheels, and i was informed the Yaris setup is like the xb, so you need a wide wheel or low offset to flush out the rear wheels.
Just wanna know if this offset is enough to get me remotely close to flush. I dont wanna know go totally flush, or have some poke until i get coilovers. As of now im just getting the lowest Tien springs.
Thanx

Angela

Replies 27

White YarisWarm Orange County · Mar 18, 2009#2
Front would work but little rubbing. Rear with that offset i highly doubt it. Maybe 30 or 35+ offset would be great.
wildmongoose26Thread starterDallas, TX · Mar 18, 2009#3
what is the problem going to be? I would be using 195/50/16's to help clear with a bit of stretch.
CASTREXCosta Rica · Mar 18, 2009#4
16x8 with 0 offset you will be WAY outside the fender!

A 35+ rear should give you the flush look.


OH BTW, NO the Yaris is not like the xB...!


the xB has more room....
cali yarisCanoga Park, CA · Mar 18, 2009#5
I have a set of wheels like that, Nilos for sale.
cm07yarisAppleton, WI · Mar 18, 2009#6
Here is a 16x7 +33 with a 205/50 for reference...

Picture not included in this copy
SplitEdmonton · Mar 18, 2009#7
^ that doesn't look lik eit would rub, but from what i've read, anything less than +42mm rubs. Hrm...
Nagoya_TRD.SoCal · Mar 18, 2009#8
best way to find out is to measure it up. a + 0 will definitely take some good coilovers and fender modifications (rolling and maybe a pull).
cm07yarisAppleton, WI · Mar 18, 2009#9
Originally Posted by Split ↑
^ that doesn't look lik eit would rub, but from what i've read, anything less than +42mm rubs. Hrm...
Can't always believe what you read...it's also lowered 1.75"
kngrsllSpartanburg, SC · Mar 18, 2009#10
Originally Posted by cm07yaris ↑
Here is a 16x7 +33 with a 205/50 for reference...

Picture not included in this copy
now thats how a wheel should fit. 👏

im orginally from kenosha, WI. i live down in south carolina now, been here for ten years now.
cm07yarisAppleton, WI · Mar 18, 2009#11
Also, here's a 16x7 +42 with a 205/50 up front...

Picture not included in this copy
Black YarisToledo, OH · Mar 18, 2009#12
Originally Posted by Split ↑
^ that doesn't look lik eit would rub, but from what i've read, anything less than +42mm rubs. Hrm...
only true for the front.... and it depends upon the tire set-up as well


I could tuck those +0 offsets' no prob!👍
UKblackyariUK · Mar 19, 2009#13
im not sure about other setups but here is my experience. Im running +38 16x6.5 all round and i have 0 rubbing and im sitting on Tein Basics. Sorry for the pics but i dont have any from the side looking down the car.

Picture not included in this copy
wildmongoose26Thread starterDallas, TX · Mar 19, 2009#14
those look good, but going for a bit of a different look. More flush, maybe even a little poke, with some mildly stretched tires.

Angela
elmoE. Tennessee · Mar 19, 2009#15
Originally Posted by cali yaris ↑
I have a set of wheels like that, Nilos for sale.


what do you want for them and pic please
CASTREXCosta Rica · Mar 19, 2009#16
Originally Posted by UKblackyari ↑
im not sure about other setups but here is my experience. Im running +38 16x6.5 all round and i have 0 rubbing and im sitting on Tein Basics. Sorry for the pics but i dont have any from the side looking down the car.

Picture not included in this copy
If you are not rubbing the crap out of the inner plastic fenders with the basics....


Then you are not driving fast enough !! 😈
UKblackyariUK · Mar 20, 2009#17
ill check the tire widths one i get home, but i know there 195/40 or 45. And i have never rubbed on this setup and believe me ive done some hard cornering in it and it still does not. The only time ive ever rubbed while havening the basics on was when i went to pick up the wheels with some friends in the back
tonygtoronto · Mar 20, 2009#18
Originally Posted by UKblackyari ↑
ill check the tire widths one i get home, but i know there 195/40 or 45. And i have never rubbed on this setup and believe me ive done some hard cornering in it and it still does not. The only time ive ever rubbed while havening the basics on was when i went to pick up the wheels with some friends in the back
so you're not rubbing because your running an improper tire size for the car? That would make your whole post irrelevant. You should be running 195/50/16 for a stock diameter.

You also say you have NEVER rubbed yet in the very next sentence you say you did rub. That’s contradictory.

So basically, yes you rub even though you run an undersized tire. If you ran a proper tire size you’d probably be rubbing all over the place.
UKblackyariUK · Mar 21, 2009#19
Originally Posted by tonyg ↑
so you're not rubbing because your running an improper tire size for the car? That would make your whole post irrelevant. You should be running 195/50/16 for a stock diameter.

You also say you have NEVER rubbed yet in the very next sentence you say you did rub. That’s contradictory.

So basically, yes you rub even though you run an undersized tire. If you ran a proper tire size you’d probably be rubbing all over the place.
for starters, im posting up my experience so theres no need to be an ass, just trying to help here. And i said that i only rubbed when i went to PICK UP the wheels. I was still running stock then and ive said that i have never rubbed ON THIS CURRENT setup. I also check with my mechanic before getting the wheels, he said it would be fine and id trust his judgment over yours any day of the week. Also from your post it seems your running with the same setup as me? if so then why not post your own experiences?
marcustoronto, canada · Apr 7, 2009#20
i wish 16x8 with +0 offset work ..my wishful thinkin..*sigh* there goes sportsmax wheel
marcustoronto, canada · Apr 7, 2009#22
that might work...
enviriCT · Apr 9, 2009#23
i got 16x7 +40s w/ 195/50r16 all around lowered on trds with zero rub, and i drive hard. :)

Picture not included in this copy
marcustoronto, canada · Apr 9, 2009#24
now that a perfect set up.
daddz07california · Feb 23, 2014#25
what about 16x8 25offset??
cali yarisCanoga Park, CA · Feb 23, 2014#26
Five years later... 😉
1.5Tampa · Feb 23, 2014#27
Haha still asking the same questions too

16x8 +25 will work with at least one of these or a combination
-camber
-tire stretch
-fender rolling

Search around more there are thousands of fitment threads
JumpmanYarisSO. INDIANA · Feb 23, 2014#28
If it fits it ships