Yarisworld Archive

DIY : How to remove door panels

14 posts · 36,536 views

FEINTOriginal postJapan · Mar 15, 2009#1
This is my contribution to Yarisworld. THis is what I am cataloging as I am going along with my yaris build. I am hoping it might help somebody.

This is done on a liftback 2009 Vitz RS.

Starting on the left hand door.

Remove the armrest piece. It just pops upwards.

Picture lost · www.mingriwa.com

This is just another illustration of the same piece that should pop up. On the other end of the door, use a small screwdriver to pop open a cover as shown in the photo.

Picture lost · www.mingriwa.com

This is what it will look like after taking off the piece.

Picture lost · www.mingriwa.com

Proceed to remove the power window switch panel and the other panel illustrated in the photo. These should both pop up as well. No tools required, just use your hands.
Picture lost · www.mingriwa.com

Remove the connector for the power window switch by pressing the tab and pulling.

Picture lost · www.mingriwa.com

This is what it looks like after removal of the above 2 pieces.

Picture lost · www.mingriwa.com

+ screwdriver required. Remove the 4 screws as shown in the photo.

Picture lost · www.mingriwa.com

To remove the door card, I pulled anywhere along the bottom of the door. It will come apart as shown.

Picture lost · www.mingriwa.com

It might require quite a yank to get it to come off. After it has seperated from the door, push the door card UPWARDS, it should come free after that.

Remove the door / lock wires from the latch.

These are where all the little grommets are located in order for you to re-attach them to the door card for installation. ***There is one more behind the hand.***.

Picture lost · www.mingriwa.com

I hope this help. :)👍

Replies 13

eTiMaGoBangkok, Thailand · Mar 15, 2009#2
hahah I just did that this morning from an old DIY, but arigato, your pics are quite clearer! 😁
LtNoogieWest Hills, CA · Mar 15, 2009#3
Ok, now I have no excuse for not pulling my door panel off to do sound deadening. Thanks for the DIY.
djgoodonyaJersey Shore, NJ · Mar 15, 2009#4
Originally Posted by LtNoogie ↑
Ok, now I have no excuse for not pulling my door panel off to do sound deadening. Thanks for the DIY.
Agreed. Can't wait for consistent nice weather. Poor Type R's are just sitting in the closet uninstalled.
ChinoCharlesOH · Mar 15, 2009#5
Note that if you have manual windows its a little tricky to remove the crank.
FEINTThread starterJapan · Mar 16, 2009#6
Originally Posted by LtNoogie ↑
Ok, now I have no excuse for not pulling my door panel off to do sound deadening. Thanks for the DIY.
I did the deadening yesterday, so here's a little DIY again.

I took off the plastic sheet then I had to remove all that sticky black silicon. I used selo tape and just stickied it off.

Picture lost · www.mingriwa.com

Picture lost · www.mingriwa.com

All done, nice and clean

Picture lost · www.mingriwa.com

Then applying the sheets should be pretty straight forward. I am going to have to re-do mine as I am not happy with the way it turned out.

Picture lost · www.mingriwa.com
AltitudeColorado · Mar 16, 2009#7
Did you put any deadening material on the inside of the external door skin or just cover those holes on the inside as seen in the photo?
FEINTThread starterJapan · Mar 16, 2009#8
Originally Posted by Altitude ↑
Did you put any deadening material on the inside of the external door skin or just cover those holes on the inside as seen in the photo?
External skin deadened, but didn't have time to take a photo. I am not finished with the deadening yet, waiting for my speakers to arrive. Then I have to get baffles and then I will deaden the door again and also over the baffles.
AstromanWenatchee, WA · May 25, 2009#9
Where is the DIY for the manual windows? Trying to figure out how to get the crank arm off.
privateyeblckbxRiverside,CA · May 27, 2010#10
Should be a spring clip behind the crank handle. Push on ur panel slightly and look behind and should see a horse shoe shaped clip. You can either remove it with a special tool which is the easiest (Harbor freight or autozone for about $5-14) or a flat screw driver or a pick will work. Careful they shoot out sometimes and are easy to lose. Pretty sure the yaris is the clip type (i have power windows), if not it can be a cover type that u remove and swing out of place to reveal a torx screw or bolt.
LarsGermany · Nov 30, 2013#11
The pictures are dead :( Can anyone repost or something? I'm getting some new speakers soon :)
PinchliteBarrie Canada · Mar 26, 2018#13
Originally Posted by FEINT ↑
This is my contribution to Yarisworld. THis is what I am cataloging as I am going along with my yaris build. I am hoping it might help somebody.

This is done on a liftback 2009 Vitz RS.

Starting on the left hand door.

Remove the armrest piece. It just pops upwards.

Picture lost · www.mingriwa.com

This is just another illustration of the same piece that should pop up. On the other end of the door, use a small screwdriver to pop open a cover as shown in the photo.

Picture lost · www.mingriwa.com

This is what it will look like after taking off the piece.

Picture lost · www.mingriwa.com

Proceed to remove the power window switch panel and the other panel illustrated in the photo. These should both pop up as well. No tools required, just use your hands.
Picture lost · www.mingriwa.com

Remove the connector for the power window switch by pressing the tab and pulling.

Picture lost · www.mingriwa.com

This is what it looks like after removal of the above 2 pieces.

Picture lost · www.mingriwa.com

+ screwdriver required. Remove the 4 screws as shown in the photo.

Picture lost · www.mingriwa.com

To remove the door card, I pulled anywhere along the bottom of the door. It will come apart as shown.

Picture lost · www.mingriwa.com

It might require quite a yank to get it to come off. After it has seperated from the door, push the door card UPWARDS, it should come free after that.

Remove the door / lock wires from the latch.

These are where all the little grommets are located in order for you to re-attach them to the door card for installation. ***There is one more behind the hand.***.

Picture lost · www.mingriwa.com

I hope this help. :)👍

What images?
KermitAUSAustralia · Nov 18, 2021#14
Following