Yarisworld Archive

Hatchback, rear door trim removal

16 posts · 23,918 views

Sodium DuckOriginal postWestern Mass. · Mar 10, 2009#1
I can't find the info in the service manual. How is the rear hatch plastic attached? Where are the clips, etc. Anybody got a page number?

Replies 15

BLAZINBLUEVITZNEW YORK · Mar 10, 2009#2
start at any corner and just pull off carefully. you might mess up a clip or 2 but it is what is is unless you have a that tool to take panels off.
Carpe_DiemColumbia, Maryland · Mar 10, 2009#3
i'd like to know as well. i have a HUGE dent in my hatch, and if at all possible, i'd like to remove the plastic piece to see if theres any way i can bang it out with a rubber mallet
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#4
Anybody else?
andru47Orlando, FL · Mar 11, 2009#5
I tired to remove the panel once, almost lost the clips to the door, had to use my fingers to fish out the clip that had fallen, let's just say my Yaris drew some blood that day. It is a real mess! Wish I knew an easier way to do it too. Will keep checking for updates!
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#7
They almost seem worth it... Are they plastic? I'd be worried about scratching/chipping paint and plastic if they were metal.
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#8
Grrr, this is annoying. I just went through the entire interior trim section of the service manual again, and it is nowhere to be found.

I guess I'll just start pulling...
CTScottUSA, CT · Mar 11, 2009#9
Originally Posted by Sodium Duck ↑
Grrr, this is annoying. I just went through the entire interior trim section of the service manual again, and it is nowhere to be found.

I guess I'll just start pulling...
This should help (from the 09 service manual):


Using a screwdriver with its tip wrapped in protective tape, slide the handle plate of the back door trim board to disengage it.

Disengage the 3 claws and 9 clips and remove the back door trim board.

Picture not included in this copy


REMOVE BACK DOOR PANEL NO.2 PROTECTOR

(a) Disengage the claw and clip, then remove back door panel protector No. 2.
Remove any tape remaining on the back door side.

Picture not included in this copy
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#10
12 fasteners? There must be something really awesome under there... LoL
Sodium DuckThread starterWestern Mass. · Mar 11, 2009#11
Thanks Scott!
AlexNet0Rockland, ME · Mar 11, 2009#12
?? where did I miss the 09 service manual? is it online?
CTScottUSA, CT · Mar 11, 2009#13
Originally Posted by AlexNet0 ↑
?? where did I miss the 09 service manual? is it online?
Not yet. I joined the Toyota TIS to have online access to it.
LtNoogieWest Hills, CA · Mar 11, 2009#14
I could not find the instructions in the 2007 manual either. There's a picture of the removed rear interior panel in the Lighting manual.
1NZYaris1New Zealand · Mar 11, 2009#15
Be Very careful insde the area off the back hatch ,where the recess is
for fingers to pull down hatch is a little plastic slot for a screw driver
insert screw driver and lever towards front of car this releases a plastic catch , now you are safe to remove cover by popping clips.
Sodium DuckThread starterWestern Mass. · Jun 14, 2009#16
Just in case anyone was curious, there's a bunch of junk behind this panel.

I was thinking about somehow fiberglassing in a sub, but there are too many things in the way. Plus, if you cut metal to make it fit, the door would lose it's structural integrity. Not worth it.