Yarisworld Archive

Throttle lag and response

20 posts · 11,883 views

yaris-meOriginal postAnaheim, CA · Mar 3, 2009#1
I bought a PLX Kiwi. I've been using it in sensor mode. I discovered tonight that there is a throttle lag and it does not open beyond 81%. No matter how much I floor it it won't go beyond 81%. On acceleration it will pause, go to 50%, pause and then 70%, then to 80%. On passing there is that same pause. I would like to say half a second to a second, but I'm guessing.

I know it's DBW (drive by wire), but this is a big lag. Also, it doesn't open beyond 81%. This can only mean that DBW is preventing full performance of the engine. Do you think this is true?🙁

Replies 19

ddongbaphay · Mar 3, 2009#2
Is this true untill redline?
yaris-meThread starterAnaheim, CA · Mar 3, 2009#3
I couldn't take it to redline, but first to third it shifted on its own at full throttle. I was on Broadway and later on Magnolia. I'll play with it some more tomorrow.
ddongbaphay · Mar 3, 2009#4
Yea, I don't think its normal. If 81% was normal, you'd still hit redline, you know what I mean?
yaris-meThread starterAnaheim, CA · Mar 3, 2009#5
I didn't have enough road to really open up the throttle. I'll have to try again on the freeway.

My initial feeling was that the DBW and engine management computer is preventing me from damaging the engine. If this is true then being able to reprogram the computer would allow you to gain more HP and better performance.
2006frontySan Bernardino · Mar 3, 2009#6
Would the Blitz throttle controller help with the 81% throttle issue? or does it just open the throttle faster getting to the 81% limit SOONER? It seems like it would help with the lag with the DBW though.
TOUGEghostKauai · Mar 3, 2009#7
Originally Posted by yaris-me ↑
I discovered tonight that there is a throttle lag and it does not open beyond 81%.
I noticed the same thing on my car. I've heard of the same issue on other DBW cars as well.
cali yarisCanoga Park, CA · Mar 3, 2009#8
The Blitz unit changes the curve but not the top limit, I think.

I've heard this post before about it not opening up past 81% -- curious.
yaris-meThread starterAnaheim, CA · Mar 4, 2009#9
Originally Posted by ddongbap ↑
Is this true untill redline?
Tonight I tried some more. I have an AT. When the water temp reach 172, I started to floor the gas. First to second it shifted at 5400 and later at 5800. Second to third shifted at 5800 and later at 6000. Third to fourth shifted at 5800 and later at 6000. After a while, the highest shift point was 6100, third to fourth. The ECU never allowed me to redline the engine and the throttle never went beyond 81%

The throttle lag is gone. I think the ECU is adaptive and after a while it eliminated the lag.
IllusionXBrossard, QC · Mar 4, 2009#10
in an automatic, i belive the ECU is able to detect your load and shift accordingly to that.

try to sit 4 in the car and do the same test again. i'm 99% sure it will shift closer to redline. At least, this is what i noticed with my 93 swift. Alone in the car, I always wondered why it would always shift at ~4000-4500rpm until one day we were 4 in the car and going on an incline... it went all the way to redline before shifting..
YarisPRMayaWest, Puerto Rico · Mar 4, 2009#11
ANy ideas on a manual?
yaris-meThread starterAnaheim, CA · Mar 4, 2009#12
Originally Posted by YarisPR ↑
ANy ideas on a manual?
I think the ECU determines maximum engine output. The ECU would probably limit fuel after 6000 RPM preventing you from damaging the engine. I think this would apply to manual also.
IllusionXBrossard, QC · Mar 5, 2009#13
the redline is somewehre around 6250rpm.

i got to the cutoff a few times.. it's around 6500rpm. i would love to have a scangauge to know the real answer to this...
1NZYaris1New Zealand · Mar 5, 2009#14
Scangauge reads the same max throttle 80% 😲
PETERPOOPOahu · Mar 5, 2009#15
dun dun dun!
blktiger60Washington · Mar 5, 2009#16
Originally Posted by IllusionX ↑
the redline is somewehre around 6250rpm.

i got to the cutoff a few times.. it's around 6500rpm. i would love to have a scangauge to know the real answer to this...

No point in waiting till 6500 RPM's to shift. That's well past the power range.

Manual:
On the freeway today, on my way to work, I downshifted to 3rd floored it to 5800 and slapped it into 4th - plenty of acceleration. I didn't notice any latency. I know for a fact I can smoke the stock tires in first and get a chirp from second. Doesn't feel like DBW to me.
TOUGEghostKauai · Mar 5, 2009#17
I wasn't complaining about any lag, but 80% throttle with the pedal all the way down does bother me.
DogetorHueThe Moon · May 2, 2017#18
I know this is an old thread, but it would seem that the ECU is intentionally limiting throttle response. Take a look at this graph from one of the manuals...

1 attachment not included in this copy

ecamposCosta Rica · May 2, 2017#19
I did some research on this issue because I was a little concerned about the throttle response in my car, its also drive by wire.

The ECU will not let the car go full throttle, it will only operate within a established rate which it thinks its "safe" to extend engine life, this in some cases can be as low as 75% throttle max.

And yes, also there is some miliseconds of lag when you push the gas pedal, its normal as well.

Things you can do to try to help it, reset ECU by unplugging negative end on the battery for a few minutes, it will respond better for a while. Clean the throttle body and MAF sensor as well as the air intake system with a cleaner for such purposes.

What I end up doing was getting a throttle controller for my car, there are many brands available. The one I bought called "Pedal Commander", it has certainly improved pedal response and it comes with several driving modes. Worth it if you ask me.

Hope this information was useful!
CartelChilliwack, BC · May 20, 2017#20
I noticed this on my car also.
80% totally sucks ass.