Yarisworld Archive

$1000 on the floor

75 posts · 18,135 views · page 1 of 2

TamagoOriginal postOff Grid · Mar 2, 2009#1
Picture not included in this copy

Replies 74

ka0sxCA east bay · Mar 2, 2009#2
is that going to be modified and go in your car?
Nexus1155Dorchester · Mar 2, 2009#3
this is what was in his car...
MorganPCB, FL · Mar 2, 2009#4
sad panda :(
largeorangefontSo Cal, OC · Mar 2, 2009#5
Whats the problem? Or do you have it out to make a jig?
TamagoThread starterOff Grid · Mar 2, 2009#6
going n/a for a bit til i can get my swap straightened out :)
cali yarisCanoga Park, CA · Mar 2, 2009#7
boo -- drive her til she blows

but seriously, what's in store for your project?
TamagoThread starterOff Grid · Mar 2, 2009#8
Originally Posted by cali yaris ↑
boo -- drive her til she blows

but seriously, what's in store for your project?
i unfortunately don't shit money.. :(

rwd and real power (torque)
cali yarisCanoga Park, CA · Mar 2, 2009#9
RWD? holy crap 🙇
TamagoThread starterOff Grid · Mar 2, 2009#10
Originally Posted by cali yaris ↑
RWD? holy crap 🙇
i figure if a yaris can do it, so can it!
MarfulionFlorida · Mar 2, 2009#11
Originally Posted by Tamago ↑
i figure if a yaris can do it, so can it!
RWD and a built 2zzge in the hood and BAM!!! lol, I can dream it at least. well the 2zzge swap has already been done, but i havent heard of a RWD yaris yet, are there any out there?
TamagoThread starterOff Grid · Mar 2, 2009#12
Originally Posted by Marfulion ↑
RWD and a built 2zzge in the hood and BAM!!! lol, I can dream it at least. well the 2zzge swap has already been done, but i havent heard of a RWD yaris yet, are there any out there?
yes, the Drift yaris.. it's here on YW. not sure of its progress though.

and the 2zz is overrated. my 1nz made more torque and almost more hp on 9psi of boost.
silver_echoSpokane, WA · Mar 3, 2009#13
you selling the old setup?
TamagoThread starterOff Grid · Mar 3, 2009#14
Originally Posted by silver_echo ↑
you selling the old setup?
sure

but no one will buy it. it's not exactly bolt-on. you'll have to make serious chop-chop of your wiper tray (xA) to make it work. not sure if it'll bolt up to a yaris without trimming the wiper tray.
silver_echoSpokane, WA · Mar 3, 2009#15
<---- not yaris... 01 echo
TamagoThread starterOff Grid · Mar 3, 2009#16
Originally Posted by silver_echo ↑
<---- not yaris... 01 echo
if you want to buy the manifold, uppipe, turbo, downpipe, charge piping, intercooler, knowing you'll have to do some serious chopping to your wiper tray to make it work, then by all means!

$500 takes what you see on the floor
silver_echoSpokane, WA · Mar 3, 2009#17
do you have a pic of what it looked like in the car?
TamagoThread starterOff Grid · Mar 3, 2009#18
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
PHXDEMONPhoenix, AZ · Mar 3, 2009#19
silver_echoSpokane, WA · Mar 4, 2009#20
crap... i would have to lose my strut tower bar...🙁
m911gtChicago · Mar 4, 2009#21
Originally Posted by silver_echo ↑
crap... i would have to lose my strut tower bar...🙁
and that wouldn't be worth gaining a FI setup? lol
cali yarisCanoga Park, CA · Mar 4, 2009#22
that is just frigging beautiful. to me, anyways.... 👏
Nexus1155Dorchester · Mar 4, 2009#23
I'm serosuly considering this and don't mind cutting some of the metal tray as long as it still works. Just wondering if you used any management unit when using this, and if you needed new injectors?... If not what AFR did it run.

oh, and any CEL light/limp ever?

I know im asking questions that might not relate to the yaris, but hey...
TamagoThread starterOff Grid · Mar 4, 2009#24
Originally Posted by Nexus1155 ↑
I'm serosuly considering this and don't mind cutting some of the metal tray as long as it still works. Just wondering if you used any management unit when using this, and if you needed new injectors?... If not what AFR did it run.

oh, and any CEL light/limp ever?

I know im asking questions that might not relate to the yaris, but hey...
with my inexperienced tuning abilities, and running JUST a MAF translator (tricks the ECU into providing more fuel) i got probably 7 codes on a weekly basis..

i was running tC injectors, they were about 60% duty cycle at WOT, full boost and high rpm (so plenty of fuel)

AFR's were between 12:1 and 11.1:1 depending on air temperature.

remember, THIS IS NOT A SHINY BOLT ON KIT!!!!! i made this kit out of left over downpipes, exhaust systems from at least 3 different cars (Subaru forrester downpipe, Mitsubishi Evo turboback, and piping from a toyota tundra)

the welds are not pretty (but are strong) and the uppipe is NOT optimized for power. my previous plan was to build an equal length manifold to replace the cast piece+uppipe but i realized that all that work would go to waste, because no one would want to pay $$ for a manifold that put the turbo smack dab into the wiper tray lol.
Nexus1155Dorchester · Mar 4, 2009#25
can you tell me what codes you got?

I mean it might not be pretty, but it worked right? thats all that really matters... did you get any knock at all with this kit, im assuming the intercooler prevented it...
TamagoThread starterOff Grid · Mar 4, 2009#26
Originally Posted by Nexus1155 ↑
can you tell me what codes you got?

I mean it might not be pretty, but it worked right? thats all that really matters... did you get any knock at all with this kit, im assuming the intercooler prevented it...

no knocking, stock ECU pulled plenty of timing (and when ihad the AEM installed, i had some timing pulled as well)

the codes i pulled with the MAF translator

system too rich
secondary o2 codes (no cat)
cali yarisCanoga Park, CA · Mar 4, 2009#27
no cats = PO420
too rich = PO702? (or close to that I recall)

Same exact ones I got with my untuned turbo system!


Can't see the mani in your pic -- post a couple more? I think you can sell that thing.
TamagoThread starterOff Grid · Mar 4, 2009#28
Originally Posted by cali yaris ↑
no cats = PO420
too rich = PO702? (or close to that I recall)

Same exact ones I got with my untuned turbo system!


Can't see the mani in your pic -- post a couple more? I think you can sell that thing.
it's a RevHard cast piece. solid as a rock, but probably not the best-flowing thing on earth.

and thx on the compliments. coming from you it means a lot (you like pretty shiney things, this is neither 😉)
KCALB SIRAYVirginia · Mar 4, 2009#29
Originally Posted by Tamago ↑
it's a RevHard cast piece. solid as a rock, but probably not the best-flowing thing on earth.

and thx on the compliments. coming from you it means a lot (you like pretty shiney things, this is neither 😉)
can it be opened a bit with a little snip snip and cut cut or is it not worth it?
TamagoThread starterOff Grid · Mar 4, 2009#30
Originally Posted by KCALB SIRAY ↑
can it be opened a bit with a little snip snip and cut cut or is it not worth it?
well, i made 155hp as-is.. so if it's worth it to you to make more power at the same PSI, then i say yeah it's worth it.

the cast piece would of course benefit from a good port/polish job
KCALB SIRAYVirginia · Mar 4, 2009#31
I just posted about it to new member that was looking to boost with the Zage kit and referred him/her to you instead if you want to get rid of it. We'll see.
Doc ZaiusOttawa, ON, Canada · Mar 4, 2009#32
Wow... that *is* ghetto-fabulous! Awesome bit of ingenuity there... I'm sure it's a blast to drive!
TamagoThread starterOff Grid · Mar 4, 2009#33
Originally Posted by Doc Zaius ↑
Wow... that *is* ghetto-fabulous! Awesome bit of ingenuity there... I'm sure it's a blast to drive!
very much so!

and yes, it is!
Russelt3hPirateEpcot · Mar 4, 2009#34
it's pretty functional! and in my eyes that is a win!

the intercooler piping/placement is a huge win.

surprised you didn't try and test mount it in russell (charge pipes anyway) while he was at the shop.
TamagoThread starterOff Grid · Mar 4, 2009#35
Originally Posted by Russelt3hPirate ↑
it's pretty functional! and in my eyes that is a win!

the intercooler piping/placement is a huge win.

surprised you didn't try and test mount it in russell (charge pipes anyway) while he was at the shop.
i'd want to test fit the entire setup really..

probably use RealEnth's if he'll let me
33OHDover, Ohio · Mar 5, 2009#36
Tamago, my '06 ZX6-R for your turbo setup + $5,000, and you fly up here and put it on for me. I'll provide you a futon and food. 🙄😁
Nexus1155Dorchester · Mar 5, 2009#37
^^^^ That is a deal and a half, go Tamago go
Nexus1155Dorchester · Mar 5, 2009#39
honestly id go buy tamagos kit and install it for you for that deal hahahaha, 1 way ticket and youd have to teach me how to ride the cycle real quick so i can get back.

Nice bike though!, I was offered an R1 for my Audi project
33OHDover, Ohio · Mar 5, 2009#40
Riding a motorcycle is easy, all you need to know is how to drive stick. =)
TamagoThread starterOff Grid · Mar 5, 2009#41
Originally Posted by ryank ↑
I'm being serious too.

http://akroncanton.craigslist.org/mcy/1050317625.html

I'll even throw in a brand new Pirelli Diablo rear tire.


You would have to make it run good, but I don't care about CEL's.
considering what i can get a bike for down here..... ;) i'll have to pass on that "deal"
33OHDover, Ohio · Mar 5, 2009#42
Oh, didn't realize motorcycles were cheaper down there.

Usually 636's go for $6500-$7000 here.
33OHDover, Ohio · Mar 5, 2009#43
Yep, there was this beauty for $2200. Same bike as mine, in Lake Alfred, Florida.

Picture not included in this copy

LOL.
33OHDover, Ohio · Mar 5, 2009#44
Tamago, are you really selling your setup? Any idea on how much would it be to ship it to me?
TamagoThread starterOff Grid · Mar 5, 2009#45
Originally Posted by ryank ↑
Oh, didn't realize motorcycles were cheaper down there.

Usually 636's go for $6500-$7000 here.
buddy of mine picked up a ninja 650R for $3000 last night


but i'm more interested in a supermoto
TamagoThread starterOff Grid · Mar 5, 2009#46
Originally Posted by ryank ↑
Tamago, are you really selling your setup? Any idea on how much would it be to ship it to me?

yes, really selling.


but it's still not a bolt on for yaris ;)
33OHDover, Ohio · Mar 5, 2009#47
What's not bolt-on about it?
ztrack157Biggs, CA · Mar 5, 2009#48
Ninja 650r < 636 or zx6r ever your try to compare a sport bike to a supersport. Tamago the bike Ryank is selling is a fucking steal with the mods it has. That tire hes throwing in isn't cheap either. Ryank on a side note I'm glad to see you dropped the price. I'd snag it for sure if you were out in CA.
33OHDover, Ohio · Mar 5, 2009#49
Yeah, a 650R is a 2 cylinder sport touring bike, lol. Has like half the horsepower of mine. But it doesn't matter, I really don't need a turbo'ed Yaris anyways.

And thanks ztrack.
Nexus1155Dorchester · Mar 5, 2009#50
I really don't need a turbo'ed Yaris anyways.
SMACK