Yarisworld Archive

squeaky clutch

14 posts · 7,962 views

redimpOriginal postcambridge england · Feb 26, 2009#1
My 03 t spirit has developed a creaky sound in the cab and a squeak in the engine when i press the clutch in. Any one know what the problem is and how to cure it.

thanks

Replies 13

TamagoOff Grid · Feb 26, 2009#2
every toyota does this

it's the pivot ball inside the trans.

pull the rubber boot off where the clutch arm goes in, and put a little grease on the pivot ball
redimpThread startercambridge england · Feb 26, 2009#3
Originally Posted by Tamago ↑
every toyota does this

it's the pivot ball inside the trans.

pull the rubber boot off where the clutch arm goes in, and put a little grease on the pivot ball
thank you, i will try that!
slothman86Savannah, GA · Feb 26, 2009#4
that white grease stuff works well i think, I can't remember what it's called
YaribhiniUSA · Feb 26, 2009#5
Originally Posted by slothman86 ↑
that white grease stuff works well i think, I can't remember what it's called
Lithium grease?
TamagoOff Grid · Feb 26, 2009#6
Originally Posted by slothman86 ↑
that white grease stuff works well i think, I can't remember what it's called
actually, lithium grease drys out quicker than say wheel bearing grease
YarisPRMayaWest, Puerto Rico · Feb 26, 2009#7
I have to check this to!!! When I press my clutch I can hear it outside of the car!!! Not even a 1977 Bettle I had that sound...
TamagoOff Grid · Feb 26, 2009#8
Originally Posted by YarisPR ↑
I have to check this to!!! When I press my clutch I can hear it outside of the car!!! Not even a 1977 Bettle I had that sound...
every toyota i've ever owned has done this.. funny stuff
PetersRedYarisThe Black Hills of South Dakota · Feb 26, 2009#9
It's actually not a ball, but a short rod (less than an inch long) with rounded ends. It look like a small ball because you can only see one end. Anyway, the slave cylinder puts pressure on the clutch arm via this rod, and the end contacting the arm does indeed get dry. The Tacoma forum crew recommends a quick shot of PBR blaster right into the socket of the every oil change. I guess it's it super easy to spray into there with the straw (sort of like a WD-40 can, only bigger) and thickens up so it stays in place...
TamagoOff Grid · Feb 26, 2009#10
Originally Posted by PetersRedYaris ↑
It's actually not a ball, but a short rod (less than an inch long) with rounded ends. It look like a small ball because you can only see one end. Anyway, the slave cylinder puts pressure on the clutch arm via this rod, and the end contacting the arm does indeed get dry. The Tacoma forum crew recommends a quick shot of PBR blaster right into the socket of the every oil change. I guess it's it super easy to spray into there with the straw (sort of like a WD-40 can, only bigger) and thickens up so it stays in place...
here's what it looks like

Picture lost · www.slowboyracing.com



and when you're spraying....
..............just keep it off the clutch disc......
whooppee777Maryland · Feb 26, 2009#11
this happened to me. wd40 fixed it. but u have to b careful not to get any on the clutch or u will get slippage
PetersRedYarisThe Black Hills of South Dakota · Feb 27, 2009#12
Originally Posted by Tamago ↑
here's what it looks like

Picture lost · www.slowboyracing.com



and when you're spraying....
..............just keep it off the clutch disc......
Hmmm, apparently we are talking about different pivot points. I am talking about the rod between the slave cylinder and the arm which also can be the cause of a squeeky clutch.
AltitudeColorado · Feb 27, 2009#13
Yeah, my old girlfriend had a squeaky clutch... oh wait... we're talking about cars.
TamagoOff Grid · Feb 27, 2009#14
Originally Posted by PetersRedYaris ↑
Hmmm, apparently we are talking about different pivot points. I am talking about the rod between the slave cylinder and the arm which also can be the cause of a squeeky clutch.
ahh

usually that's not the one that squeaks, that i've found.. it's the pivot point INSIDE the trans