YodaOriginal postFL · Feb 19, 2009#1..... i got the NST UD pulley today and well tried to install it and omgwtfpwnz😢 i cant get the bolt off. my impact gun is a 1/2 drive so i couldnt get a good grip
on it to cover the bolt with the socket. I manage some how to get it in a little slanted and a little grip. That didnt work. I am working with a 250 tq electric gun😕. Any suggestions???
By the way thats the only gun i could get.
Replies 42
PETERPOOPOahu · Feb 19, 2009#2bigger gun with a big compressor!
YodaThread starterFL · Feb 19, 2009#3Its electric and i not gonna go get another one then go buy a compressor for $$$.About to have a mech do it.... is the like a extension for the gun?
turboyarisSouthern New Jersey · Feb 20, 2009#4put the car in gear, and get a breaker bar
jkuchtaL.A. · Feb 20, 2009#5^+1....That's how I'm going to get 'er done on Monday at Microimage.
$10 breaker bar at harbor freight can "fix" anything.
TOUGEghostKauai · Feb 20, 2009#6You should be able to use a short extension for the impact if you can't get it to fit directly on the bolt. Putting the car in gear and using a breaker bar is a pretty abusive way to do it (if that even works). There's another way to do it with a breaker bar, but I don't think anyone who knows wants to give up the secret due to liability reasons. 😆
eTiMaGoBangkok, Thailand · Feb 20, 2009#7insane mechanics when I got mine installed could not loosen it by hand either... so one guy held on the breaker bar real strong while the other cranked the engine for a split second... Worked like a charm! Though be careful if you try this, you probably don't want to clean up pieces of shredded appendages from your engine bay...
CtrlAltDefeatIndianapolis IN · Feb 20, 2009#8I was able to get it loose with just a breaker bar and a rubber strap wrench... cranking the engine with the breaker bar on the the nut is insanely dangerous... you could hurt yourself and/or the car.. I would NOT recommend it...
CtrlAltDefeatIndianapolis IN · Feb 20, 2009#9In case you're wondering I wrapped the strap wrench around the pulley, and braced it against the chassis so I didn't have to hold it, and just cranked real hard on the breaker bar... If you think you might have problems with that, get a pipe to go over the end to lengthen it so you can get more leverage... as Archimedes said, “Give me a lever long enough, and a prop strong enough, I can single-handed move the world.”😁
TOUGEghostKauai · Feb 20, 2009#10 Originally Posted by
eTiMaGo ↑ insane mechanics when I got mine installed could not loosen it by hand either... so one guy held on the breaker bar real strong while the other cranked the engine for a split second... Worked like a charm! Though be careful if you try this, you probably don't want to clean up pieces of shredded appendages from your engine bay...
I should have known someone out there knew an even worse way to do it. 😆
at3GGVA Beach · Feb 20, 2009#11heh notice he never said it was a good way are necessarily recommended it. You can get a tire back on the rim by spraying combustibles inside it then lighting a match, but why the hell would you actually try it?
YodaThread starterFL · Feb 20, 2009#12i gonna see if i can get an extension for the gun when i get off work and try it one more time if not then i see if i can find a breaker bar somewhere...
jkuchtaL.A. · Feb 20, 2009#13TOUGEghost,
You're telling me putting the car in gear and applying the brakes (to keep the engine from spinning), and then using a 30" long breaker bar with a fully seated socket is abusive?
Explain.
YodaThread starterFL · Feb 20, 2009#14got some more tools gonna give it another try
jkuchtaL.A. · Feb 20, 2009#15Were all behind you Yoda🙂
YodaThread starterFL · Feb 20, 2009#16ok i got the bolt off not too bad just needed an extender and some back bone... now new prob i put the alternator bact to the positioned i marked it at but the belt still feels loose
so i tried making it a little tighter and started the engine....it squeals really loud help me plz -_-'
YodaThread starterFL · Feb 20, 2009#17so i put it in the stock position again turned the car on and you kno what only the pulley spins🤷 its just spining there with the belt on it.
i am thinking there is a sweet spot somewhere
supmetSouthern California · Feb 20, 2009#18 Originally Posted by
Yoda ↑ so i put it in the stock position again turned the car on and you kno what only the pulley spins🤷 its just spining there with the belt on it.
i am thinking there is a sweet spot somewhere
sounds like the belt isn't tight enough... if its tight, the belt pretty much HAS to move with the pulley.
YodaThread starterFL · Feb 20, 2009#19i got it to move now but when i push the pedal it sequels a little.
jkuchtaL.A. · Feb 20, 2009#20Check the belt deflection at the midpoint between the crank and the alt pulleys. The deflection on a belt used more than 5 min. is 11-13mm (assuming you're using the old belt). The service manual in the DIY section has the specs and a diagram.
Too much belt tension can kill the water pump bearing.
YodaThread starterFL · Feb 20, 2009#21ok got int good but now i have that red battery light. the books says that means its have problems charging...
jkuchtaL.A. · Feb 20, 2009#22Is the alternator spinning?
YodaThread starterFL · Feb 20, 2009#23let me check
YodaThread starterFL · Feb 20, 2009#24yes it is. do i need to make it tighter just a bit?
jkuchtaL.A. · Feb 20, 2009#25What is the deflection of the belt right now (engine off).?
YodaThread starterFL · Feb 20, 2009#26its 12mm then i again i am using a ruler. there seems to be a very very very small point where it will not sequel and have the battery light off the best i got was a little sequel with the battery light off. you thing driving it a bit will make it go away?
well i go the sequel sound to go away on start up and the battery light but when you give it some gas it sequels
jkuchtaL.A. · Feb 20, 2009#27Is it a new belt, or the old one. Chances are that driving it will make the noise go away after a little while it it's a new belt.
YodaThread starterFL · Feb 20, 2009#28i got 5000 miles on it
Ive always known squealing ment your belt was too lose.
PETERPOOPOahu · Feb 21, 2009#30I didn't even mark the original place of the alternator. Just moved it so the belt was tight and good to go!
CtrlAltDefeatIndianapolis IN · Feb 21, 2009#31the alternator needs to be moved past where it was before you installed the pulley... the pulley is smaller so there's more slack on the belt mine moved about an inch
Picture not included in this copy
before
Picture not included in this copy
after
YodaThread starterFL · Feb 21, 2009#32hmm i see i will take care of it later i got ice on my car....
YodaThread starterFL · Feb 21, 2009#33got it fixed and running havent gotten to really get on it yet i will let you all kno later on
YodaThread starterFL · Feb 22, 2009#34😁👍WOT😳
Its nice...its real nice. I mean nice. I got the tq i lost from the header and more.
Now i have a new problem... My thrid gear grinds when i shift into it hard. At normal driving it doesnt but i still feel it just a little😕
CtrlAltDefeatIndianapolis IN · Feb 22, 2009#35err um.. It shouldn't have messed with that.... maybe you're too eager with the shifts?🤷
CtrlAltDefeatIndianapolis IN · Feb 22, 2009#36but yea, I love my pulley🤤 I think it even sounds better🤘
PETERPOOPOahu · Feb 22, 2009#37It's probably your shifting.
JerkrattFair Lawn, NJ · Feb 22, 2009#38or the syncros not lining up fast enough... i get that sometimes when im at high rpms shifting into third
YodaThread starterFL · Feb 23, 2009#39so what do i do take it to the dealer or wat?
jkuchtaL.A. · Feb 23, 2009#40If you haven't yet, change the trans fluid to Redline MT-90, or other GL-4 fluid. You'll need 2 bottles.
You'd be amazed at how big a difference this stuff makes!
YodaThread starterFL · Feb 23, 2009#41its a manual tho doesnt just use the engine oil...?
jkuchtaL.A. · Feb 23, 2009#42No, the transmission uses its own fluid. A GL-4 spec 75W-90 weight oil like Redline MT-90 is perfect. You'll need 2 quarts for a complete fill.
YodaThread starterFL · Feb 26, 2009#43ok so the dealer ordered a new trans for me yea. o also about the pulley... i notice that my mpg has also increased by 2 and this was while i was WOT 80%. My mpg has never been higher ever even when i baby it. i current sit at 32 mpg WOT 80% of the time total city driving. I love this dang thing