just like topic says. please tell me how valves in the head wind up getting bent????
BENT VALVES in the head: tell me how that happens....
28 posts · 12,100 views
Replies 27
over revving.. stretching of the timing chain... vvti solenoid going bad and allowing too much timing advance..
or in my case.. snapping a connecting rod.
or in my case.. snapping a connecting rod.
got an 08 tc which was in before and had motor/head replaced under warranty for a ticking noise in the valvetrain. customer is back 3 months and 15,000 miles later and now ALL of the valves in the head are bent?
So what's the customer's story?
what weight of oil is he running?Originally Posted by BLAZINBLUEVITZ ↑got an 08 tc which was in before and had motor/head replaced under warranty for a ticking noise in the valvetrain. customer is back 3 months and 15,000 miles later and now ALL of the valves in the head are bent?
wait.. you're coming to YARISWORLD for tech support? 🤣🤣
and i quote " i drive 200 miles a day and never go above 70mph on the highway" and "all i did was get gas and car statred to lose power afterward"Originally Posted by jkuchta ↑So what's the customer's story?
car has intake and header( which were removed before he brought in) as well as secondary cat delete and megan exhaust.....
customer did a 1-2-1 shift or a 2-3-2 shift. he over-rev'd the engine.Originally Posted by BLAZINBLUEVITZ ↑and i quote " i drive 200 miles a day and never go above 70mph on the highway" and "all i did was get gas and car statred to lose power afterward"
car has intake and header( which were removed before he brought in) as well as secondary cat delete and megan exhaust.....
warranty DENIED
edit: have the tech pull off the crankshaft pulley and look for scoring on the roll pin.. you'll find it's most likely bent or almost broken.
Assuming the install was done correctly Tamago is probably right.
although if the install wasn't done right it could be numerous things.
although if the install wasn't done right it could be numerous things.
...and that's a problem because?Originally Posted by Tamago ↑wait.. you're coming to YARISWORLD for tech support? 🤣🤣
Does the timing chain still have tension?
iirc the newer chain tensioners are oil pressure activated and ratcheting... so they'd take up any slack.. so yeah, you may want to check that the teeth on the tensioner are not worn off.. but i still sniff a mis-shift.Originally Posted by rob323 ↑Does the timing chain still have tension?
not as much a problem as a slight source of amusement to me.. because most of the 'knowledge' on this forum orbits around what offset wheel you can run without rubbing and what weight of oil you can/cannot run...Originally Posted by Altitude ↑...and that's a problem because?
so a question about bent valves being asked here where the OLDEST yaris on the forum (US, anyway) is approaching 3yrs old.
probably because any talk of STREET RACING or ripping around the twisties with a new part installed is off limits....👎Originally Posted by Tamago ↑not as much a problem as a slight source of amusement to me.. because most of the 'knowledge' on this forum orbits around what offset wheel you can run without rubbing and what weight of oil you can/cannot run...
.
Valves were probably adjusted too tight if they had to do any kind of valve adjustment. Tight valves would lift too much causing contact with the piston and bending the valves.
Does the Yaris have a rev limiter like my old Passat? I don't drive mine as wildly as I did my old VR6, plus it is an auto, so I don't know...
Cheers! M2
Cheers! M2
Yes, it's set at 6K RPM. Valve damage would occur if driven for too long like that because of strain and overheating.
lol dude...Originally Posted by FunctionSpec ↑Valves were probably adjusted too tight if they had to do any kind of valve adjustment. Tight valves would lift too much causing contact with the piston and bending the valves.
tight valves.. lifting too much... yet somehow coming in contact with the pistons??
the valve springs lift the valves, the cams push them down..
blazinblue did your tech check the crankshaft pulley yet?
Barring extremely unusual circumstances, don't valves only get bent when they come into contact with pistons? There's really only one way that can happen... the valve timing has gone off in a major way. Typically, that means something broke (timing chain broke or stretched, VVT messed up, whatever) or the engine was severely over-revved to the point that the valve springs couldn't keep up and one or more valves stayed open when they should have been closed.
I'm going with the "3-2 shift". Winding up 3rd and missing 4th, dumping the clutch in 2nd gear with the car going 80 mph. Ponder that for a moment. If the engine turns about 6200 rpm at 60 mph, you can easily zing it past 8000 in this manner... instantly. And if you're not quick enough to realize it instantly (or quite possibly even if you are), you can do some damage in a hurry.
I did it once in my old Saturn, but I realized it before I even got the clutch fully engaged and no damage occurred. From what I'm seeing with my son as he's learning the finer points of driving a stick... if he did it, he'd more likely fully engage the clutch and leave it there and wonder "why don't I have any power" until valves started poking holes in the hood. And I don't think my son is all that unusual as far as young folks learning to drive stick go.
Remember, a rev-limiter can save you from over-reving under power. The engine will simply never rev ITSELF far enough to hurt itself, the ECU won't let it. But NOTHING can save you from a botched shift! The solution is to learn to trust your shifter. Don't FORCE your shifts, "guide" your shifts. The shifter is spring loaded and will go into the proper place if you let it.
I'm going with the "3-2 shift". Winding up 3rd and missing 4th, dumping the clutch in 2nd gear with the car going 80 mph. Ponder that for a moment. If the engine turns about 6200 rpm at 60 mph, you can easily zing it past 8000 in this manner... instantly. And if you're not quick enough to realize it instantly (or quite possibly even if you are), you can do some damage in a hurry.
I did it once in my old Saturn, but I realized it before I even got the clutch fully engaged and no damage occurred. From what I'm seeing with my son as he's learning the finer points of driving a stick... if he did it, he'd more likely fully engage the clutch and leave it there and wonder "why don't I have any power" until valves started poking holes in the hood. And I don't think my son is all that unusual as far as young folks learning to drive stick go.
Remember, a rev-limiter can save you from over-reving under power. The engine will simply never rev ITSELF far enough to hurt itself, the ECU won't let it. But NOTHING can save you from a botched shift! The solution is to learn to trust your shifter. Don't FORCE your shifts, "guide" your shifts. The shifter is spring loaded and will go into the proper place if you let it.
Originally Posted by Loren ↑Barring extremely unusual circumstances, don't valves only get bent when they come into contact with pistons? There's really only one way that can happen... the valve timing has gone off in a major way. Typically, that means something broke (timing chain broke or stretched, VVT messed up, whatever) or the engine was severely over-revved to the point that the valve springs couldn't keep up and one or more valves stayed open when they should have been closed.
I'm going with the "3-2 shift". Winding up 3rd and missing 4th, dumping the clutch in 2nd gear with the car going 80 mph. Ponder that for a moment. If the engine turns about 6200 rpm at 60 mph, you can easily zing it past 8000 in this manner... instantly. And if you're not quick enough to realize it instantly (or quite possibly even if you are), you can do some damage in a hurry.
I did it once in my old Saturn, but I realized it before I even got the clutch fully engaged and no damage occurred. From what I'm seeing with my son as he's learning the finer points of driving a stick... if he did it, he'd more likely fully engage the clutch and leave it there and wonder "why don't I have any power" until valves started poking holes in the hood. And I don't think my son is all that unusual as far as young folks learning to drive stick go.
Remember, a rev-limiter can save you from over-reving under power. The engine will simply never rev ITSELF far enough to hurt itself, the ECU won't let it. But NOTHING can save you from a botched shift! The solution is to learn to trust your shifter. Don't FORCE your shifts, "guide" your shifts. The shifter is spring loaded and will go into the proper place if you let it.
hey, everyone, Loren's here! now you can believe what i said waaay back in post #2 lol
Yeah. What you said!Originally Posted by Tamago ↑hey, everyone, Loren's here! now you can believe what i said waaay back in post #2 lol
(as is typical of me, I said the same thing, just used a helluva lot more words)
Literally you are right but technically valve "lift" is the distance the valve moves from full close to full open. So how far the cam pushes the valve "down" is valve "lift".Originally Posted by Tamago ↑lol dude...
tight valves.. lifting too much... yet somehow coming in contact with the pistons??
the valve springs lift the valves, the cams push them down..
Mis-shift would also be another possibility but he never mentioned if it was auto or manual.
Usually when this happens the computer records the live data. It will record engine rpm and vehicle speed in freeze frame. Dealer can see how fast you were going and what rpms. If you are above redline and shows you going 100mph and engine coolant temeprature shows the vehicle isnt even warmed up then dealer is going to say sorry bozo.
I mean usual way to bend valves is when you have the piston colliding with the valves due to incorrect timing or in most cases cars that run timing belts and the belt brakes. I have seen a mechanic install a timing chain wrong once engine ran for a few seconds and you hear this clack clack clack. removed the cylinder head and the piston snapped the valve off turned it upside down and it punctured a hole through the piston head.
I mean usual way to bend valves is when you have the piston colliding with the valves due to incorrect timing or in most cases cars that run timing belts and the belt brakes. I have seen a mechanic install a timing chain wrong once engine ran for a few seconds and you hear this clack clack clack. removed the cylinder head and the piston snapped the valve off turned it upside down and it punctured a hole through the piston head.
Since this car is at a Toyota dealer... do the Toyota diagnostic tools have the ability to look at things like "max RPM" and such? I would think a missed shift situation would show up as a pretty serious RPM spike. Max speed might be in there, too... 70 mph?
Haha! We must have been telepathically linked.Originally Posted by YarisSedan ↑Usually when this happens the computer records the live data.
i've done it :(Originally Posted by Loren ↑Since this car is at a Toyota dealer... do the Toyota diagnostic tools have the ability to look at things like "max RPM" and such? I would think a missed shift situation would show up as a pretty serious RPM spike. Max speed might be in there, too... 70 mph?
3-4-3 :( didn't take too much speed
3rd gear is good to about 80 mph, so you'd have to be going considerably faster than that in 4th to get into trouble by going back down to 3rd, wouldn't you? Dunno how sensitive this engine is, I guess if it's particularly fragile, maybe it doesn't take much.Originally Posted by Tamago ↑i've done it :(
3-4-3 :( didn't take too much speed
Or is it the immediate acceleration of the engine to 6000 rpm rather than high rpm itself that's causing it to break?
FYI: its a manual TC.......
i'd imagine that the extreme acceleration to ANY rpm would cause a temporary flex of the valvetrain (cams, vvti setup, timing belt) enough to throw valves into a place they don't belong.Originally Posted by Loren ↑3rd gear is good to about 80 mph, so you'd have to be going considerably faster than that in 4th to get into trouble by going back down to 3rd, wouldn't you? Dunno how sensitive this engine is, I guess if it's particularly fragile, maybe it doesn't take much.
Or is it the immediate acceleration of the engine to 6000 rpm rather than high rpm itself that's causing it to break?
and yes, i was going considerably faster than i should have been.. it snapped the crankshaft pulley's rollpin (thankfully no harm was done to the crankshaft) and slightly bent at least one set of valves..