ka0sxOriginal postCA east bay · Feb 10, 2009#1Pardon the quality of the images but the majority were taken on from my cellphone as i went.
I might have posted this log before the jack.
This has been my ongoing project since the summer of 07 and is nearing completion.
The car is a 1986 Porsche 944
The engine Toyota 1JZGTE
I will add descriptions to the picture over the next few days as this is a lot to post all at once.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Replies 23
ka0sxThread starterCA east bay · Feb 10, 2009#2Picture not included in this copy
12.5 lbs lightweight 1jzgte Flywheel
Direct from Japan, $230
Picture not included in this copy
Stage II pressure plate came with 7mgte disk
(if you need the 7mgte clutch disk I still have it)
Picture not included in this copy
Machined the center clutchhub and spliced it with the 944 bearing.
Picture not included in this copy
I had to pull the manifold off to put the new wiring harness on decided to clean it up and paint it with caliper paint while i had it off. Just some color for now.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
ka0sxThread starterCA east bay · Feb 10, 2009#3Picture not included in this copy
layout for the adapter plate, matching the stock automatic bellhousing to the torque tube.
Picture not included in this copy
cut out and drilled.
Picture not included in this copy
Finished plate with the alignment bolts for the torque tube.
Picture not included in this copy
machined out the bellhousing for the clutch fork and slave cylinder
Picture not included in this copy
Test fit of the engine in the engine bay.
Picture not included in this copy
The engine In the engine bay and mounted to the torque tube.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
The motor mounts fabricated on spot with the engine in the car.
Picture not included in this copy
Picture not included in this copy
Engine sitting in the engine bay on the new motor-mounts.
The rubber 944 bottom bushings will soon be replaced to change it to be a solid mount.
ka0sxThread starterCA east bay · Feb 10, 2009#4Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
missing map sensor.....
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
ka0sxThread starterCA east bay · Feb 10, 2009#5Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
ka0sxThread starterCA east bay · Feb 10, 2009#6Picture not included in this copy Picture not included in this copy Picture not included in this copy Picture not included in this copy Picture not included in this copy Picture not included in this copy Picture not included in this copy video http://www.youtube.com/watch?v=Zes7MDeIxRQ MorganPCB, FL · Feb 10, 2009#7that is going to be fun when you're finished! Good luck!
TamagoOff Grid · Feb 10, 2009#8excellent powerplant choice!
TheRealEnthMiami, FL · Feb 10, 2009#9hah wow... what a coincidence.... why not an LS1?
ToddRNorthern IL · Feb 10, 2009#10I had to laugh at the picture of you upside down in the drivers seat. I can't count the number of times I've been in the same position.
blacksandiegovitzJust chillin' out brah ! · Feb 10, 2009#11Holy shit ! Thats the first time I've ever seen a 944/1jz swap very nice work man , the install looks super clean .
33OHDover, Ohio · Feb 10, 2009#12Freaking awesome.. 👍
eTiMaGoBangkok, Thailand · Feb 10, 2009#13yum... one of my favorite Porsches with a more modern, badass engine... 👍
CrandallNo Funswick · Feb 10, 2009#14Props for the work. I'm sure you must be excited to take it out for a rip.
I personally wouldn't have painted the piping blue, but if it floats your boat then good on ya.
ka0sxThread starterCA east bay · Feb 10, 2009#15 Originally Posted by
Crandall ↑ I personally wouldn't have painted the piping blue, but if it floats your boat then good on ya.
Im cheep, i would have polished and chromed it, but i don't intend for this to be so much of a show car, and i happened to have caliper paint laying around.
Originally Posted by TheRealEnth
why not an LS1?
why not a gopher?
LS1 = aprx $2500 + shipping
1JZ only cost me $1000 shipped.
LS1 and LT1s already have kits for them.
After every thing is tested I plan to have the parts machined, documented, patented and maybe even sell kits. who knows.
I also love the Toyota engines.
Originally Posted by Morgan
that is going to be fun when you're finished! Good luck!
My advice, don't buy ABSpowerbrakes unless you love shitty customer support, I ask for a wiring diagram for the unit and i get a shitty picture.
So that is my biggest issue right now.
ka0sxThread starterCA east bay · Feb 23, 2009#16Cali Weather has sucked ass lately, I have had enough clear time in between all the rain to install the "heater" radiator with a higher water reserve point. Will have pic up soon, have also removed some more carpeting and dead weight.
Now that the plumbing is done for the extra radiator I have two more things to do before I test drive it.
*brake booster wiring (from scratch now...)
*solid motor mounts (no room for engine flex/wobble)
badass
jinxorSydney, Australia · Feb 23, 2009#18This is an amazing project... Great work mate
ka0sxThread starterCA east bay · May 18, 2009#19So today I ripped out the ABSpowerbrake-piece-o-shit booster and am installing a stock booster from a turbo model 1.5 inches higher up on the brake pedal with no vacuum booster to work as manual brakes, I understand other people that do the LS and LT swaps do this and it works out quite well.
TheRealEnthMiami, FL · May 18, 2009#20PICS PICS PICS
ka0sxThread starterCA east bay · May 18, 2009#21 Originally Posted by
TheRealEnth ↑ PICS PICS PICS
I need to cut a mount plate and mount it up, ill post pictures when I have it fabbed up and mounted.
SilverBackEl Monte, Ca · May 18, 2009#22It's winking in the very first pic lol
Bad ass project though. Looks good so far 👍
ka0sxThread starterCA east bay · Jun 5, 2009#23So I put the original master cyl back on to be used manual brake wise.
Picture not included in this copy
then i started on the push rods, threaded one to the old thread and fucked it up working on it, so i redid the end and made a new pushrod, one that will work better.
Picture not included in this copy
mikenacaratoBrentwood, TN · Jun 5, 2009#24dude.....way badass!!!!!