Yarisworld Archive

one of my custom driveshaft builds: (pix)

18 posts · 9,956 views

TamagoOriginal postOff Grid · Feb 9, 2009#1
found an old set of pictures on one of the first "custom" shafts i did at work. this is for an F22 powered AE86 corolla. the original design (not by me) failed and almost punctured through the floor of the car. the second try is what we see below

we start with the CV end from an S2000.. it's made from what we call "propellor" style shafting, small on the ends, larger in the middle. we cannot use this tube because it's metric, and all our tubing is inch. because of the very high RPM requirements, i must step the tube diameter up to 3" .083 wall tube for strength and integrity..

here's how the shaft started out.
Picture not included in this copy

i remove the CV end:
Picture not included in this copy

and cut the stub off the metric tubing, leaving a little tubing to work with.
Picture not included in this copy

then begin welding: (keep in mind, all im' doing is weld on top of weld, slag and crap is not a concern at this point as it gets burned off in the process)
Picture not included in this copy
Picture not included in this copy


next, chuck the stub up in the lathe
Picture not included in this copy
and begin turning.. my target diameter is around 2.85 since i want a press fit into an .083 wall tube

annnd all done cutting:
Picture not included in this copy
Picture not included in this copy

then i take the stub over to the press, and use good ol hydraulics to force the stub into a piece of 3" tubing:
Picture not included in this copy

then cut the tube to length and press on the "other" end. bolt up to the balancer and start welding
Picture not included in this copy
Picture not included in this copy


all welded, balanced and painted flat black per customer request:
Picture not included in this copy

car is making around 500whp and have had no issues to this day. (original work was about a year ago)

C/C welcome

Replies 17

MorganPCB, FL · Feb 9, 2009#2
welding without gloves is a no-no! ;)

looks awesome, I bet that car flys!
TamagoThread starterOff Grid · Feb 9, 2009#3
found another pic. this one doesn't have a build log, but it may be more appreciated cuz i have pix of the actual car lol

it's a toyota Supra (2JZGTE) engine, Tremec 6spd (stock twinturbo manual transmission for a supra) mated to a ford 8.8 thirdmember rear end:

Picture not included in this copy

and here's the beauty it went in. took 3 separate trophies at HIN miami for this season

Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

one of the cleanest and sickest builds by far that i've ever seen. i have huge respect for RAW (rich auto works) who built this car.
mikenacaratoBrentwood, TN · Feb 9, 2009#4
very sweet! how much do you charge for that kinda stuff. im going to need a custom drive shaft and 4 axles soon.
TamagoThread starterOff Grid · Feb 9, 2009#5
Originally Posted by mikenacarato ↑
very sweet! how much do you charge for that kinda stuff. im going to need a custom drive shaft and 4 axles soon.
all depends. actual fab work if it's a "standard" driveshaft (no machining, etc) i charge $65 for a complete assemble/straighten/weld/balance.

what transmission and rear end?
TamagoThread starterOff Grid · Feb 9, 2009#6
Originally Posted by PK198105 ↑
very nice work Tamago. i have the utmost respect for people who create things from scratch and with their hands. so you are saying its strong enough?

do you only do drive shafts? or anything that deals with fabrication.?
i try to fabricate everything i can for my car and others cars. working with metals is one of my passions.

i've only been building driveshafts for a couple years now. aside from my ghetto turbo setup, lately fab work has been pretty slow because of the economy. :(
mikenacaratoBrentwood, TN · Feb 9, 2009#7
its an evo engine and transmission going into a volvo s40. im not sure if i will have to have them shortened, but i think i will. also they will have to be beefed up for sure. the driveshaft and all 4 axle shafts
TamagoThread starterOff Grid · Feb 9, 2009#8
Originally Posted by PK198105 ↑
can you make a laptop mount like this:
http://cgi.ebay.ca/ws/eBayISAPI.dll?...m=120356014194

how does it attach to the laptop? i'd probably buy an inexpensive camera tripod and build off it.

could be done, but probably not as inexpensive as an ebay product
TamagoThread starterOff Grid · Feb 9, 2009#9
Originally Posted by PK198105 ↑
there is a strap that keeps it to the plate. but i guess yours would be more expensive
mass production usually leads to products that are pennies on the dollar for custom built stuff.. at my $30/hr i charge you'd have yourself a pretty spendy piece.
TamagoThread starterOff Grid · Feb 9, 2009#10
Originally Posted by PK198105 ↑
yup but you pay for quality dont ya 👍
this is true :)
ka0sxCA east bay · Feb 9, 2009#11
Tamago are you in a machine shop or an autoshop, or both?

if you guys do machining how much do you think a rough cost of something like this would be, to be machined from moderate steel. The size is about 16"x16"
Picture not included in this copy
Picture not included in this copy
TamagoThread starterOff Grid · Feb 9, 2009#12
unfortunately, my machining capabilities are very limited. i only have two lathes (management sold my vertical milling machine and the welder i used for aluminum, as well as my drill press) so i'd not be able to build the above piece.
ka0sxCA east bay · Feb 9, 2009#13
Originally Posted by Tamago ↑
unfortunately, my machining capabilities are very limited. i only have two lathes (management sold my vertical milling machine and the welder i used for aluminum, as well as my drill press) so i'd not be able to build the above piece.
thats unfortunate, I am limited to using bandsaws, welders and lathes at home and without a proper mill i cant do it myself and im not about to invest more money that i don't have >,<

thanks.
TamagoThread starterOff Grid · Feb 10, 2009#14
Originally Posted by mikenacarato ↑
its an evo engine and transmission going into a volvo s40. im not sure if i will have to have them shortened, but i think i will. also they will have to be beefed up for sure. the driveshaft and all 4 axle shafts
i missed this post. i'd HAVE to see what flange yoke was on the rear end of the Volvo. typically this would be a 3pc shaft if you utilized an evo stock drivetrain (what rear end are you using?) and why can't you use stock axles? the evo axles hold well over 700whp.

anyway, with a core, (basically front two pieces of an evo shaft) i can build you a 2pc conversion (rear half from aluminum, 15.5lbs lighter than stock) for around $700..
cali yarisCanoga Park, CA · Feb 10, 2009#15
cool beans, Tamago! 👏

I'm coming down there -- you can build me a roll cage.
TamagoThread starterOff Grid · Feb 10, 2009#16
Originally Posted by cali yaris ↑
cool beans, Tamago! 👏

I'm coming down there -- you can build me a roll cage.
nah, best go to a certified rollcage shop :)
firemachine69Sudbury, On · Feb 11, 2009#17
Originally Posted by Morgan ↑
welding without gloves is a no-no! ;)

looks awesome, I bet that car flys!
Guilty here! 😳


Good job! Any reason to not just go a commercial route?
TamagoThread starterOff Grid · Feb 11, 2009#18
Originally Posted by firemachine69 ↑

Good job! Any reason to not just go a commercial route?
what do you mean a commercial route?