Yarisworld Archive

Ideal Spacer Width For the Rear?

17 posts · 12,468 views

tk-421Original postDagobah · Jan 26, 2009#1
My wheels are 15x6.5" ET +38
My tires are 205/50R15
I am sitting on NF210 springs

These are the spacers I want to get. They're available from 10mm-25mm through MicroImage.

Would 10mm be enough for the rear without rubbing, or should I go for 15mm? TIA

Replies 16

Black YarisToledo, OH · Jan 26, 2009#2
10mm on that low of an offset wheel
kimonaHuntington Bch, CA · Jan 26, 2009#3
10mm
Russelt3hPirateEpcot · Jan 26, 2009#4
depending on your suspension you may rub with the +38mm offset.

a 7" +25mm rear is a pretty good look with some camber and coilovers though. :)

I think the 15mm would be too much though.

although you should look into hubspacers instead of "wheel" spacers.
tk-421Thread starterDagobah · Jan 26, 2009#5
Thanks for your help! 🙌

Originally Posted by Russelt3hPirate ↑
depending on your suspension you may rub with the +38mm offset.

a 7" +25mm rear is a pretty good look with some camber and coilovers though. :)

I think the 15mm would be too much though.

although you should look into hubspacers instead of "wheel" spacers.
I have NF210 springs riding on stock shocks. So far I have absolutely no rubbing (not even with the car full) and I want to keep it that way.

The spacers that I linked to are hubcentric BTW.
Russelt3hPirateEpcot · Jan 26, 2009#6
hubcentric and hubspacer are two different things.

hubspacer mounts between the hub and the axle spacing the hub 10mm (therefore also the wheel).

a wheel spacer (hubcentric or not) will space out the wheel only.

how are you doing on space between the tire and the fender at full compression?

with our setup at +25mm it's very close to hitting the fender and it does on a rare occasion depending on the severity of the bump.
tk-421Thread starterDagobah · Jan 26, 2009#7
Originally Posted by Russelt3hPirate ↑
hubcentric and hubspacer are two different things.
Really? Didn't know that... 😳

how are you doing on space between the tire and the fender at full compression?
I haven't really measured, but something close to an inch. I think I should be fine with 10mm... I'll make some real measurements and post up though.
Russelt3hPirateEpcot · Jan 26, 2009#8
the key is under compression.

fill up your trunk/backseat with fat friends/family and measure away. :)
tk-421Thread starterDagobah · Jan 27, 2009#9
Originally Posted by Russelt3hPirate ↑
the key is under compression.

fill up your trunk/backseat with fat friends/family and measure away. :)
OK.. I just tried measuring the aforementioned gap under compression. it looks like I have almost 3/4 of an inch (~1.5 cm) between the sidewall and the fender.

So yeah... I think 10mm is definitely as close as I want to get. 15 mm would end up rubbing for sure. 😲

Thanks again for your help guys! On to find hubspacers...
ddongbaphay · Jan 27, 2009#10
Originally Posted by Russelt3hPirate ↑
depending on your suspension you may rub with the +38mm offset.

a 7" +25mm rear is a pretty good look with some camber and coilovers though. :)

I think the 15mm would be too much though.

although you should look into hubspacers instead of "wheel" spacers.
I don't get it, whats the difference between a 25mm, and a 38mm with a 10mm spacer?

Thats only a 3mm difference.
2006frontySan Bernardino · Jan 27, 2009#11
Originally Posted by tk-421 ↑

Thanks again for your help guys! On to find hubspacers...
I can't find those hubspacers for the life of me, I think Evolved Concepts might have went out of business because their website doesn't work for me anymore. I personally prefer the hub spacers over the H&R spacers, IMO the hub spacers seem a little easier to install since you don't have to deal with longer studs.
Russelt3hPirateEpcot · Jan 27, 2009#12
Originally Posted by ddongbap ↑
I don't get it, whats the difference between a 25mm, and a 38mm with a 10mm spacer?

Thats only a 3mm difference.
3mm is alot when we're talking wheels and tires.

a 48mm might fit but i doubt a 51mm would.

even a 45mm to a 48mm.

it isn't alot when you're in the appropriate range but once you're on the outside edge or inside edge of the range 3mm can mean the difference between rubbing and fitting perfect.
tk-421Thread starterDagobah · Jan 27, 2009#13
Originally Posted by 2006fronty ↑
I can't find those hubspacers for the life of me
Yup... Same here. I tried eBay, but there's either Ichiba or H&R wheel spacers. Nothing comes up for the term "hubspacers". 😠
Russelt3hPirateEpcot · Jan 27, 2009#14
contact Tamago he may know how to get you some.
tk-421Thread starterDagobah · Jan 27, 2009#15
Originally Posted by Russelt3hPirate ↑
contact Tamago he may know how to get you some.
Looks like he has PMs turned off on his account. 🙁
kimonaHuntington Bch, CA · Jan 27, 2009#16
Contact yarisworld member, caliyaris.
Russelt3hPirateEpcot · Jan 27, 2009#17
Originally Posted by tk-421 ↑
Looks like he has PMs turned off on his account. 🙁
it should work after today.