this may be dumb, but will the nitto midpipe bolt right on to my tanabe medalion axleback? thanks
Q about nitto midpipe?
28 posts · 11,585 views
Replies 27
I'm pretty sure it does, but some modifications may be needed depending on which header you have.
Someone please correct me if I'm wrong.
Someone please correct me if I'm wrong.
cool and thank you. i still have the stock header.
bolted up to my tanabe exhaust fine, it did not however bolt up fine to my weapon r header, requiring some hack saw trimming on the header.
sweet 🙂 thanks man
Should bolt up fine. Tanabe piping is the same as stock 🤷
how about the dc ceramic header?
It should, I got my Nitto from Malaya and he was running a DC Sports ceramic header.Originally Posted by mikenacarato ↑how about the dc ceramic header?
awesome, thanks!
dont put an exhaust on the yaris! if anything put on a nitto mid-pipe. when i had the nitto mid-pipe it actually made the car quieter and deeper. the only thing is it made it idle rough when holding the brake while in drive. this might not be a concern for standard transmission owners. the aftermarket exhausts sound kinda ricey except for maybe the vitz one and the trd ones. the nitto one i have is kinda ricey sounding, i think i'm going to add another resonator to quiet it down.
my is300 on the other hand... even with a complete straight pipe its deep! (watch in high quality)
http://www.youtube.com/watch?v=7D29N...e=channel_page
my is300 on the other hand... even with a complete straight pipe its deep! (watch in high quality)
http://www.youtube.com/watch?v=7D29N...e=channel_page
my tanabe medalion axleback sounds low and deep ( and under 93db). i think the trd exhaust sound and looks bad, but thats just me 🤷
the more muffling and baffling the better on 4cyl motors unless they're a boxer setup (check out impreza sound clips: http://www.youtube.com/watch?v=ehQXURqg8vA) or they're turbo (which works as a muffler: http://www.youtube.com/watch?v=F2THJ_QYDig). Or better yet, a combo of the two: http://www.youtube.com/watch?v=-Cj1Jfq1Low
Great input with supporting clips Split. Did you try the nitto pipe with stock exhaust? If it made it quieter I'd get one before I buy an exhaust.
That is a great question - Does adding just a Nitto midpipe make the overall exhaust quieter???
Wait, what are you talking about?Originally Posted by Split ↑the more muffling and baffling the better on 4cyl motors unless they're a boxer setup (check out impreza sound clips: http://www.youtube.com/watch?v=ehQXURqg8vA) or they're turbo (which works as a muffler: http://www.youtube.com/watch?v=F2THJ_QYDig). Or better yet, a combo of the two: http://www.youtube.com/watch?v=-Cj1Jfq1Low
Just curious if adding a nitto midpipe not only adds some performace but is quieter than stock.
Split...I dont think the Tanabe medallion sounds ricey at all. Its deep and still quiet, ive gotten lots fo compliments. Now as far as the midpipe adding power. Ive heard so many arguments on whether or not certain exhaust systems raise or decrease high mid or low range power, its just so convuluted and i wouldnt trust anyones opinion wiohtout a dyno sheet.
So what's the specific differences between the stock midpipe and the nitto midpipe? I'm pretty noob at car performance stuff. I think I finally have the audio thing down though :)
Larger diameter pipe = more flow , cat deleate = more flow , Stainless steal piping = looks real good and won't rust. Good for a couple to a few hp's depending on other modds .Originally Posted by wsladaritz ↑So what's the specific differences between the stock midpipe and the nitto midpipe? I'm pretty noob at car performance stuff. I think I finally have the audio thing down though :)
plus three resonators (instead of the cats) to help mellow down the exhaust 🙂
and by mellow down u mean....? it's quieter? or lower?
Thx for the info guys 😁
Thx for the info guys 😁
well I only had my old HKS exhaust to compare since I changed it too, so some of what I hear now is also due to the Nitto muffler,but yes, it has a relatively quiet and low tone... not high pitched and buzzy.
I will be getting more of these in stock in a few weeks, FYI
Hey Garm got any of those O2 cel eleminators in stock , drop me a pm if yes .Originally Posted by cali yaris ↑I will be getting more of these in stock in a few weeks, FYI
Since this is the "offical" nitto midpipe question thread, I have one...
Does it fit the stock yaris header? I plan to upgrade my header as well (to a DC Sports header) but money is a tad tight right now.
-Thanks
Does it fit the stock yaris header? I plan to upgrade my header as well (to a DC Sports header) but money is a tad tight right now.
-Thanks
I second that question except I do not plan on upgrading the header later. It does fit the stock header right?
I believe the question of fitment on stock headers was answered with a yes. DC fitment is also confirmed and weapon R needs custom cutting
the tanabe medallion is the quiet one right? if so, that's probably a gooder.