Yarisworld Archive

The $53.50 eBay HID Kit Installed & Working

66 posts · 15,926 views · page 1 of 2

The ArchitectOriginal postFL · Dec 30, 2008#1

So I made myself a guinea pig, plus my buddy had a $70 set from ebay with great results so I went for it.

The kit is a 35W H1 8000K

Heres the pictures and a video as well.

The video was taken with a point n shoot camera so dont be too hasty to call the light output bad because its actually very good.



Half & Half

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy



Picture not included in this copy

SAME AS ABOVE EXCEPT SPED UP TO SHOW WARM-UP PERIOD

Picture not included in this copy


Picture not included in this copy

Replies 65

thebarberGrand Rapids, MI · Dec 30, 2008#2
i wouldnt go w/ 8000k personally...poorer visibility than other colours...

did you end up losing your high beams?
The ArchitectThread starterFL · Dec 30, 2008#3
that i did, i thought i ordered the 6000k but i guess i forgot. either way theyre drastically brighter than the 6000k bulbs i had in before, im very happy.
jinxorSydney, Australia · Dec 30, 2008#4
is that a 35W kit or a 55W kit?
The ArchitectThread starterFL · Dec 30, 2008#5
35w

55w jumps up to i think $159 on ebay, idk about anywhere else.
jinxorSydney, Australia · Dec 30, 2008#6
can you post a link to the hid page mate... thanks
Kaotic LazagnaCentral Valley, CA · Dec 30, 2008#7
Looks a tad bit high. Can you aim them down a bit?

Picture not included in this copy

Unless the driveway is inclined.
The ArchitectThread starterFL · Dec 30, 2008#8
http://cgi.ebay.com/ebaymotors/XENON...Q5fAccessories


thats what ive thought since the day i got the projectors.

im sure i can, ive heard you have to adjust the screws inside the headlight near where the bulbs go in.

anyone wanna fill me in?
Kaotic LazagnaCentral Valley, CA · Dec 30, 2008#9
Originally Posted by The Architect ↑
http://cgi.ebay.com/ebaymotors/XENON...Q5fAccessories


thats what ive thought since the day i got the projectors.

im sure i can, ive heard you have to adjust the screws inside the headlight near where the bulbs go in.

anyone wanna fill me in?
hmmmm...
The ArchitectThread starterFL · Dec 30, 2008#10
the difference is drastic, i dont even need my fogs anymore. id recommend them to everyone so far.

Ill give an update should anything change in stability/functionality etc.
Kaotic LazagnaCentral Valley, CA · Dec 30, 2008#11
Yeah, my HID's are a huge upgrade from the stocks, the Luminics, and the Sylvannia's I had prior to it. Although, since I don't have projectors, it's a bit glar-ie, so I had to aim them waaaay down.
GreenSpeedThe Sea of Salt · Dec 30, 2008#12
I just picked up a set of the depo lights like yours. I'm sure there's a thread about it somewhere, but was the install simply mounting the ballast, connecting wires and replacing the stock bulb with the Xenon bulb?

Well done on the videos and pics!
The ArchitectThread starterFL · Dec 30, 2008#13
keep in mind i no longer have my high beams, then again it should also be noted that the projectors reach pretty high up while also not blinding any oncoming traffic.

the install was very straight forward, swab the bulbs, plug in the power and ground to the stock harness...and your golden.
Yaris PalmeAustria · Dec 30, 2008#14
i don´t like this HID Kits..... This kits are flashing the other drivers in front of you so much...... for the other driver it looks like he is looking direct into the sunlinght.
The ArchitectThread starterFL · Dec 31, 2008#15
not with the projectors, the cutoff is great and ive never been high beamed/flashed/etc. for any stray light.
Kaotic LazagnaCentral Valley, CA · Dec 31, 2008#16
To prove non-believers wrong, I've seen people take pics of their lights behind another car (parked) to show where the cutoff is at.
89GLHFrederick, MD · Dec 31, 2008#17
theres the reason aftermarket HID kits are illegal in some states. For $1 I bet the stock lights light better.
The ArchitectThread starterFL · Dec 31, 2008#18
lol

haha
33OHDover, Ohio · Dec 31, 2008#19
Originally Posted by 89GLH ↑
theres the reason aftermarket HID kits are illegal in some states. For $1 I bet the stock lights light better.
I have an 8000K HID kit as well and it's a million times brighter.

The stock lights are so dim; I got SilverStar Ultras and they still weren't bright.

The HID Kit not only looks cool, but is definitely brighter than stock. Why wouldn't it be?

And also, you just aim them at the ground and nobody gets blinded.

Glad to see yours worked out for you Architect. 👍
The ArchitectThread starterFL · Dec 31, 2008#20
gracias senor, my thoughts exactly.

(thats my highscool spanish in full effect)
beardaGermantown, MD · Dec 31, 2008#21
Originally Posted by 89GLH ↑
theres the reason aftermarket HID kits are illegal in some states. For $1 I bet the stock lights light better.
They aren't illegal in some states, they're illegal in all states.
Kaotic LazagnaCentral Valley, CA · Jan 1, 2009#22
Originally Posted by ryank ↑
I have an 8000K HID kit as well and it's a million times brighter.

The stock lights are so dim; I got SilverStar Ultras and they still weren't bright.

The HID Kit not only looks cool, but is definitely brighter than stock. Why wouldn't it be?

And also, you just aim them at the ground and nobody gets blinded.

Glad to see yours worked out for you Architect. 👍
+1. I have a 6000k set on my sedan.
GreenSpeedThe Sea of Salt · Jan 1, 2009#23
I think I'm gonna take the plunge and add this kit to my depot lights. Just to be sure, I need to order the 9300 Hi/Lo Bulb(Hi-Halogen/Lo-HID) kit, correct?

Appreciated!
The ArchitectThread starterFL · Jan 1, 2009#24
im not sure how it would work if you have the depo projectors and you bought the bi-xenon kit, since theres seperates bulbs for high and low beam on the depo projectors I would think that 2 sets of HIDs would be need, one for highs and one for lows....

please correct me if im wrong and i very well may be.
taKutoToronto · Jan 2, 2009#25
do not bother with a 'bixenon kit' if you have projectors. Projectors use a fixed focal length, and the design of a projector does not allow you to make use of any sort of high beam bulb. Bixenon projectors will be what you'll want, but these require retrofitting of a bixenon HID projector (TL, E46, FX45,E55,RS6, etc)

hid kits into projector headlights will not produce glare, this is just by design. A metal shield prevents light from passing a certain point (aka the cutoff). Glare kits in a reflector housing is what everyone hates on. Don't mix these two up. As long as it's a projector, it's much more respectable over a glare kit in your stock reflector headlights.

Only downfalls with most ebay/depo projector headlights is their lack of width. This is why halogen bulbs in those projectors offer poor performance. But with an HID kit, you boost the intensity and suddenly the concern for width doesn't matter to you because you'll be satisfied with the upgraded light intensity.

The Architect, from your pictures it does not look like you got 8000k. This is normal for most companies to give you different color temperature bulbs as china kits are a hit-or-miss on color temperature. It's good you didn't get 8000k as they are terrible. Your pictures look more in the 5000-6000k range.
The ArchitectThread starterFL · Jan 2, 2009#26
yeai was pretty sure i ordered 6000k and they look to even be 6000k but the box said 8000k so i went with it.

thanks for clearing it all up.

one last question in case you know.

on our headlight harnesses which are of course female, there are three slots ot be filled, left, right and then one on top between the two. (as shown below)

DISREGARD THE WORDS AND LINES

Picture not included in this copy


What is the purpose of each slot?

Is one for low beam and one for high and one for ground or what.

I want to know what needs to be done or what needs to be plugged in for the second set of HIDs (when i get them) to be able to be used as high beams.
Kaotic LazagnaCentral Valley, CA · Jan 2, 2009#27
I can't remember (and Thomas helped me out on this), but I think one is positive, one is negative, and one is a ground.
ViolinNew Jersey · Jan 2, 2009#28
You've got power (always on), low ground and high ground. If you add a second set to use as high beams, your lows will turn off when the highs turn on. You'll be blind while they strike and warm up. Switching the ballasts on and off will kill them and the bulbs.

A better way would be to keep the halogens in and build this harness which will keep the HID lows on when you turn on the halogen high beams. It also allows you to flash the highs without turning on the lows.

1 attachment not included in this copy

89GLHFrederick, MD · Jan 2, 2009#29
for the record, DO NOT PUT HIDs IN A REFLECTOR HOUSING. Thats what I'm referring to. If they're in a projector housing (what they're made for) they dont bling you (as much) as if they were in a reflector housing.

http://www.youtube.com/watch?v=yVuSSdZNsZw
GreenSpeedThe Sea of Salt · Jan 2, 2009#30
I'm terrible at reading schematics and even worse at electrical work...are the R1, R2 and R3 boxes meant to be connectors and where could I pick them up? Do the repeated ovals in each box represent a fuse? Sorry to be such a nuisance, but I want to do this properly when the HID kit and projectors show up. A shopping list for the harness would be very helpful.
taKutoToronto · Jan 2, 2009#31
those three are relays. That circuit seems to just allow HID's to be turned on only when parking light is on. I can't see a use for R2.
eTiMaGoBangkok, Thailand · Jan 2, 2009#32
just read through this thread, a few observations...

1) It looks like the car is on an incline, which is why the cutoff seems so high?
2) As these projector lights have separate bulbs for high and low beam, there's no reason why you'd have to lose the high beam?
The ArchitectThread starterFL · Jan 2, 2009#33
well there is a slight incline yes, but not enough so to justify it being as high as it is, during normal driving it is noticeable although not a problem.

And the high beams are gone because the headlights harness isnt being used anymore, the HIDs "harness" if you can call it that is being used, I suppose one could just snip off the harness and add a tiny ring terminal to the proper wire and reinsert it into the female harness.
ChinoCharlesOH · Jan 2, 2009#34
89GLH - You missed one point. All projectors aren't made for HID's! IMHO, the only way to go is HID bulbs in HID REFLECTOR housings! I wish they made the blacked out headlights in this format, but they don't. However, depoautolights does make a set of headlights with HID projectors in them. cali yaris is one of the few to have them, and they're fantastic.

GreenSpeed - those are relays. Violin has a fantastic thread about his retrofit here: DIY - HID Retrofit. THAT is the way to put HID projectors in your car. His were from a BMW E46 if I'm not mistaken.
GreenSpeedThe Sea of Salt · Jan 2, 2009#35
Originally Posted by ChinoCharles ↑
GreenSpeed - those are relays. Violin has a fantastic thread about his retrofit here: DIY - HID Retrofit. THAT is the way to put HID projectors in your car. His were from a BMW E46 if I'm not mistaken.
Great article Charles. Thanks!
SilverBackEl Monte, Ca · Jan 2, 2009#36
That's insanely bright! I would personally drop it down to 5000K to get a more optimal white projection without the excessive brightness. That's just me though

On the bright side (no pun intended), maybe now we won't find anymore threads about LBs hitting deers 😆
ChinoCharlesOH · Jan 2, 2009#37
Originally Posted by GreenSpeed ↑
Great article Charles. Thanks!
Hey, no problem. If you have any further questions PM me. I probably won't know the answers, but I will know where/who to direct you to.
LafiroNYC · Jan 3, 2009#38
Is there a depo projector kit for the yaris sedan?
And if not, maybe I should get the bixenon kit the same ebay seller has?(I need a new HID kit ASAP!!!)
The ArchitectThread starterFL · Jan 3, 2009#39
No there is not a depo projector set for the sedan.

Ill let the others chime in about whether you should get what if any HIDs to put in the regular reflective housing.
taKutoToronto · Jan 3, 2009#40
bixenon glare kits are utter fail. HID low beam, mini halogen high beam. Definitely grabs attention with the big difference in light intensity.
When I went with a glare kit, I decided to lose the high beams. I hardly use high beams in city anyways, who needs them when your glare lights up the sky.
LafiroNYC · Jan 3, 2009#41
The way I have the ones I have now are in the regular hosuing, but there is an adapter that is suppose to have a cutoff of light, and then the bulb(H4 I believe) then goes inside that normally, and when I set the lights down enough, I must say it does a good job at lighting, and I dont get highbeamed, but the cutoff light is smeered and not exact like projectors obviously. I was just wondering if it was a good idea to do the bixenon light just to get my hi-beams back.

I wish they made the depo projectors for the sedan, I do not understand the reason why no company has done so yet.
window_leeCanada · Jan 3, 2009#42
i am having the projector headlight too,. i am wondering how to fit the H1 HID for the H4?
The ArchitectThread starterFL · Jan 3, 2009#43
canada huh, sounds a bit off but uhh lets see.

if youve got the depo projectors like everyone else then you just need an H1 HID Kit, they slide right and your good to go....pretty much.
GreenSpeedThe Sea of Salt · Jan 4, 2009#44
^^^^Uh, oh. I picked up the 9300 HID kit because that's the headlight bulb size listed on the sticky in this forum. I hope that's not gonna create a major problem.
LafiroNYC · Jan 4, 2009#45
Yeah I was going to ask, whats the difference between H4 and 9003? Stock bulbs are listed as 9003, but the ones already installed are H4.
GreenSpeedThe Sea of Salt · Jan 4, 2009#46
^^^yup...meant to say 9003.
LafiroNYC · Jan 7, 2009#47
What do you guys think about the bi-xenon kits with the moving bulb instead. Is this better then having a single bulb with 2 light sources inside?
nsmitchellRichmond, VA · Jan 7, 2009#48
So these "Swift Retrofits" drop right in? $307.00? That sounds interesting... I like the black projectors. I think it would look sweet with my red LB.
The ArchitectThread starterFL · Jan 7, 2009#49
yes they do, ive seen some on ebay for less than that.
GreenSpeedThe Sea of Salt · Jan 8, 2009#50
I got the 9003 kit in and sure enough, it's significantly larger than the opening of the depot projectors. If anyone has the depot style projectors and plans to add this HID kit, be sure to follow Architect's advice and get the H1 kit!!!

I ended up re-ordering the H1 and am going to try and work out a refund for the 9003 set with the vendor.

Architect, you said that the H1 kit fits almost perfectly. The stock depot projector bulbs are so freakin tiny (no wonder people complain about the output). What type of modification did you need to do to get the H1 bulbs to fit and secure in place?

This has been a great thread BTW.