Yarisworld Archive

motor oil drain plug washer

14 posts · 12,401 views

xpeteyjtxOriginal postMassachusetts · Dec 29, 2008#1
Has anyone purchased that plastic washer for the drain plug? How much does the dealer want? Does anyone know the size?

I should have taken out the calipers when I was doing my oil change and measured the washer... maybe I could get some replacements from a parts/hardware store for cheap.

Replies 13

gidNortheast · Dec 29, 2008#2
we were given them for free with TOYOTA oil filters we bought . Not sure of the price , maybe the dealer that you purchased the car from would give you 1 or more at no / low cost . Can't hurt to ask . GOOD LUCK
1NZYaris1New Zealand · Dec 29, 2008#3
i paid a $1.50nz for my washer on the last oil change , bought it from Toyota
03Z33SoCal · Dec 29, 2008#4
They're usually less than $0.20 at most autoparts, around $0.50 at my local Toyota dealer.
auxmikeLI, New Yawk · Dec 29, 2008#5
Those washers are aluminum with a blueish gray paper adhered to both sides.
I got 10 for $10 shipped on Ebay.
I'd only use a dealer part here. Too "mission critical" at part to skimp on....🤷
gidNortheast · Dec 29, 2008#6
we were given those as well . There's 2 type . The plastic would be longer lasting .
xpeteyjtxThread starterMassachusetts · Dec 29, 2008#7
I bet I could get some cheap aluminum washers from the hardware store. I guess I will have to measure the diameter of the thread next time.
1NZYaris1New Zealand · Dec 29, 2008#8
Originally Posted by xpeteyjtx ↑
I bet I could get some cheap aluminum washers from the hardware store. I guess I will have to measure the diameter of the thread next time.
To answer your question 12.mm (1/2") 😁 replaced my drain plug
with a alloy one with a magnet in it 😁
aca72Santa Clara, CA · Dec 29, 2008#9
It's Toyota part # 90430-12031. That's 10-pack.
xpeteyjtxThread starterMassachusetts · Dec 30, 2008#10
Originally Posted by 1NZYaris1 ↑
To answer your question 12.mm (1/2") 😁 replaced my drain plug
with a alloy one with a magnet in it 😁
you are the best
now I need to find a 13-14mm (.562") ID aluminum washer

so what exactly is the thread on the drain bolt?
TheSilkySmoothNew Hampshire · Dec 30, 2008#11
Originally Posted by xpeteyjtx ↑
you are the best
now I need to find a 13-14mm (.562") ID aluminum washer

so what exactly is the thread on the drain bolt?
The TOY washer for the older 2azFE is better being rubberized and good for 4-6 uses if you dont WAIL on it torques wize. - and only a masochist would pay a buck for a 2 cent washer. I would not use Al here though due to possibility it would corrode OFFF the car in the winter, maybe instead a solder tinned Cu washer. That being said I DID spend a buck on this 5c washer at the dealer 'cause I was TOO LAZY to walk into the hardware store and look for copper washers ... So I am Lazy but NOT a masochist🤷

bro for sonja
TheSilkySmoothNew Hampshire · Dec 30, 2008#12
Originally Posted by xpeteyjtx ↑
you are the best
now I need to find a 13-14mm (.562") ID aluminum washer

so what exactly is the thread on the drain bolt?
On a related subject, Though they are good filters DONT use thepurolator filter 'cause the nipple on the filter mount is too short and you will engage less than 2 threads - which is recipe for disaster.

Any one else have short nipple or is it just our car(08 3dr 1.5L 5 spd)

hey xpete, I'm in Wilmington, MA🎉
xpeteyjtxThread starterMassachusetts · Dec 30, 2008#13
Originally Posted by TheSilkySmooth ↑
On a related subject, Though they are good filters DONT use thepurolator filter 'cause the nipple on the filter mount is too short and you will engage less than 2 threads - which is recipe for disaster.

Any one else have short nipple or is it just our car(08 3dr 1.5L 5 spd)

hey xpete, I'm in Wilmington, MA🎉
I did not know that about the purolators. the toyota denso filters spin quite a few times before the rubber is seated.

I'm on the other side of the pike.
TheSilkySmoothNew Hampshire · Dec 30, 2008#14
Originally Posted by xpeteyjtx ↑
I did not know that about the purolators. the toyota denso filters spin quite a few times before the rubber is seated.

I'm on the other side of the pike.
Yes the Densos spin a few times, you prob noticed how the threaded hole is pretty much flush to the top edge.

My cube mate live in Athol.

-the bro