Yarisworld Archive

Who here has done oil change without a jack???

36 posts · 13,660 views

YaweshOriginal postlong island · Dec 29, 2008#1
i mean, the drain plug is so conveniently located near the front bumper, i can just sttick my head in and turn it with my ractchet

Replies 35

xpeteyjtxMassachusetts · Dec 29, 2008#2
I have never use jacks/ramps to do an oil and filter change on the Yaris.
DFAPanama City, Panama · Dec 29, 2008#3
wtf
My yaris has stock suspension and I can't even start to get under there.

But hey, if you fit, go for it. I know I would.
xpeteyjtxMassachusetts · Dec 29, 2008#4
Originally Posted by DFA ↑
wtf
My yaris has stock suspension and I can't even start to get under there.

But hey, if you fit, go for it. I know I would.
Well I don't think many people would "fit" under there. I lay down on the ground next to the car (you may be able to get your head under the car) and reach for the drain plug and oil filter.

No dealing with jacks/ramps and it is safer.
Chrsto4Barrie, Ontario · Dec 29, 2008#5
I avoid the jack all together and just use my horn. I tap it gently and the dealership opens the bay door.

Yes...🙄...even as I write this I KNOW I'm being a winky stick but...I...just...can't...help myself. Seriously though, kudos to all you DIYs who save a buck and gain a sense of pride. Cheers. 👍
YarisSedanCalifornia - Bay Area · Dec 29, 2008#6
My car is lowerd so cant really fit under there. But i park it on my driveway so its already slightly angled. THen put the jack under the lift point on the passanger side front. Brings the front end enough to fit under there easily.
gidNortheast · Dec 29, 2008#7
use homemade wooden ramps . 2" (h) x 12"(w) x 36" long with one end cut at an angle ( to drive up ) and a 2 pieces ( stopper ) of 2"x2"x12" , which 1 is nailed / screwed to each end of ramp to stop car from going over the edge . Make sure it's not split or too many knots for strength . Would think pressure treated be best to endure weight .
Bullet120Kansas City · Dec 29, 2008#8
I've done an oil change w/o ramps or a jack a couple times and did a filter swap topside with the hood raised. THE reason I bought this car was long term cost of ownership. The ease of working on it is a huge benefit, too.
ChinoCharlesOH · Dec 29, 2008#9
TRD suspension = I need me some jack stands!
auxmikeLI, New Yawk · Dec 29, 2008#10
I jack up the driver's side and then go to town.....👍
GeneWPennsylvania · Dec 30, 2008#11
Trivial - you get an oil pan no higher than about seven or eight centimeters. You buy a wrench for the bolt (I think it's a 17mm but am not certain) and an oil filter socket.

I routinely do my oil in the street without a lift. One of the reasons I bought this car was for this reason.

Gene
elmoE. Tennessee · Dec 30, 2008#12
i use ramps, makes life a lot easier, i ain't no "youngster" so i have learned the easier the better
hopVancouver Island B.C. · Dec 30, 2008#13
I dont use jacks or ramps.. I am 6 foot 200lb and i can get it done.

i can almost do it on my knees and just reach under with a socket wrench.. when the bolt is loose take the wrench out slide the pan under and take the bolt out with your fingers.
cleongSingapore · Dec 30, 2008#14
A Fumoto oil sump drain valve makes it a lot simpler.
Rich kDutchess NY · Dec 30, 2008#15
What brand / types of pan to drain the oil into fit under the yaris w/o jacks ramps?
rningonfumesSoCal · Dec 30, 2008#16
Originally Posted by cleong ↑
A Fumoto oil sump drain valve makes it a lot simpler.
You have the valve? Did you need to put anything around the threads? Waiting for my next oil change to put it on.
gidNortheast · Dec 30, 2008#17
Originally Posted by gid ↑
use homemade wooden ramps . 2" (h) x 12"(w) x 36" long with one end cut at an angle ( to drive up ) and a 2 pieces ( stopper ) of 2"x2"x12" , which 1 is nailed / screwed to each end of ramp to stop car from going over the edge . Make sure it's not split or too many knots for strength . Would think pressure treated be best to endure weight .
go to , http://s49.photobucket.com/albums/f2...0Oil%20Change/ . Click on images for a look . Nice 1st generation XB too . Kin to the YARIS .
nemelekArizona · Dec 30, 2008#18
I do
ddongbaphay · Dec 30, 2008#19
Nobody just curbs their car?
MUSKOKA800Chatham, Ontario, Canada · Dec 30, 2008#20
I use ramps. Between the front lip and lowering springs I need the clearance to work the wrench and have room for catch pan. Plus while up on the ramps the oil pan is tilted back toward the drain for a quicker, more thorough dump.
gidNortheast · Dec 30, 2008#21
Originally Posted by gid ↑
go to , http://s49.photobucket.com/albums/f2...0Oil%20Change/ . Click on images for a look . Nice 1st generation XB too . Kin to the YARIS .
could just use use layer of 2" ( H ) x 10" (or 12") (W) x 36" ( L ) . Be easier for car to climb and oil pan be angled . Better yet , use 1 board of 1 level under 1 or both wheels on drivers side . That way pan be sloped for better drainage . Hope I'm not confusing 😕 you to much . 😁
xpeteyjtxMassachusetts · Dec 30, 2008#22
Originally Posted by Rich k ↑
What brand / types of pan to drain the oil into fit under the yaris w/o jacks ramps?
My pan has a maximum height of 4.5". You have to loosen the drain bolt with a wrench, then remove it with your left hand, while using your right hand to maneuver the pan under the bolt.
ChupacabraCT · Dec 30, 2008#23
I have DF210's and can do it w/o any problem. No ramps...no boards. I have the fujitomo valve installed but it's not necessary in any way. Just handy to have a ball valve drain system. No tools needed to do an oil change. Hand tight filter and ball valve drain.
YAR1SRaleigh, NC · Dec 30, 2008#24
I use ramps...
sportin83central IL · Dec 30, 2008#25
i just changed mine 15 mins ago and i didnt use a jack and i am 6'5" and round 240. i just twist filter loose stick pan under and pull bolt out and let it run. its simple takes longer to let oil drain than to actually get bolt and filter out.
churpTropical Minnesota · Dec 30, 2008#26
Ice cream bucket and a 2x4 under each front wheel works fine with my 1.5" drop in the springs.
mikenacaratoBrentwood, TN · Dec 30, 2008#27
i did my oil change lowered with df210 springs without a jack.
gidNortheast · Dec 30, 2008#28
Originally Posted by churp ↑
Ice cream bucket and a 2x4 under each front wheel works fine with my 1.5" drop in the springs.
you sure you're not milking a cow ? 😁
gidNortheast · Dec 30, 2008#29
A 2"x4" under each front wheel sounds a bit dangerous 😲 . You starting a new X-treme sport 😉 ? 1 under each tire on drivers side might be less dangerous , plus help oil drain better since the oil pan is sloped toward the passenger side ( right ) . Hope you use bricks , rock , piece of scrap wood , or a gold bar behind each wheel .
Snyprwlf47Cannelton, WV · Dec 31, 2008#30
Floor jack is the solution to all!!!! Plus I cant get to my filter without it!
yaris-meAnaheim, CA · Dec 31, 2008#31
I use store bought ramps. It's safe and easy to drain and change filter. They go on sale for about $14.00.
cleongSingapore · Dec 31, 2008#32
Originally Posted by rningonfumes ↑
You have the valve? Did you need to put anything around the threads? Waiting for my next oil change to put it on.
Yes, and no. Buy the correct one and its a direct fit. The lever might not be oriented exactly how you like it but when I want to drop my oil I'll just rack my steering all the way to the right side and my hand can easily reach in the gap to get the valve.
ZINGLebanon, Middle East. · Jan 1, 2009#33
Here they make you take it to the dealers for an oil change, although I wish I could do it myself. Have no hand on experience with cars, whatsoever.


EDIT: and they charged me 22$
cleongSingapore · Jan 1, 2009#34
I've thrown my packaging away but based on Fumoto's chart, F-103 would be it. But I would email them to make sure, though.
floydisrockPhoenix Arizona · Jan 2, 2009#35
The yaris oc is simple,as everything is right up front.
15 mm socket is the only tool required.
slvryarisIndiana · Jan 2, 2009#36
I do. I jack the driver side a little just to squeeze my big head underneath of it even though its not completely safe.