richardholdenerOriginal postLas vegas, NV · Nov 18, 2008#1Here is a graph of the baseline runs with the stock yaris (the one we are using to design production intake with). The after graph is a result of a few mods including the new long-tube header, Dynatek intake, Xd TB and NST under drive pulleys. It looks like exceeding 120 wheel hp will definitely be possible with bolt on mods assuming they inlcude the long-tube header 9and mid pipe) and new intake manifold. This test was run with a version that is identical to the production piece so these gains will be possible. Possibly more power with light-weight oil, tuning from FIC (needs more ignition timing) and real CAI (we ran the stock filter lid turned upside down)-I forgot my TRD/AEM CAI back in Vegas for this test (in Palmdale). We might be able to get to 130 wheel hp in real street trim! BTW-Check out post on intake update.
1 attachment not included in this copy
Replies 47
pinoypizzaboylas vegas/ henderson · Nov 18, 2008#2where can i get richard holdner built stickers for my car?
mikenacaratoBrentwood, TN · Nov 18, 2008#3whats different about the xd TB than the yaris?
richardholdenerThread starterLas vegas, NV · Nov 18, 2008#4The Xd throttle body is larger than the Yaris but it plugs right in and runs perfectrly on the yaris. Just needs a minute or two to idel down the first time you start it-ECU is not use to having such large throttl eopenings at idle but once this self adjustment takes place right after initial start up-it works perfectly and was worth roughly 2 hp at this power level. Intake will come with flange to accept Xd TB and have adapter plate to neck down for yaris TB.
Originally Posted by
mikenacarato ↑ whats different about the xd TB than the yaris?
mikenacaratoBrentwood, TN · Nov 18, 2008#5awesome! your the man richard!
ChinoCharlesOH · Nov 18, 2008#6Richard, how are these N/A geared mods going to work with a forced induction setup? Will they still add power? I understand that they aren't designed for use with a turbocharger, but I am hoping that they will still add to the whole picture and not take away.
richardholdenerThread starterLas vegas, NV · Nov 18, 2008#7For a turbo application, the intake and NST pulleys will work well. Can't really do a long-tube header for turbo application-but it would definitely help if it could be fit-anything that helps NA power will help in forced induction. A rotrex blower set up could use all of the listed mods. Blitz blower could use long-tube header and pulleys (all could use a good CAI).
Originally Posted by
ChinoCharles ↑ Richard, how are these N/A geared mods going to work with a forced induction setup? Will they still add power? I understand that they aren't designed for use with a turbocharger, but I am hoping that they will still add to the whole picture and not take away.
pinoypizzaboylas vegas/ henderson · Nov 18, 2008#8im a noob but 20+ whp is a big change for the yaris ecu wont this require some management of some sort? this is almost the same gains as the blitz🙂
jkuchtaL.A. · Nov 18, 2008#9So tell me about this long tube header. When will it be available, and will it mount to the stock midpipe?
EDIT: I just saw the other thread!
eTiMaGoBangkok, Thailand · Nov 18, 2008#10niiiiiiice, now that is a meaty increase across the range 😁 👏
Dylan YapSingapore · Nov 18, 2008#11do you have a AF chart too? dynojet can print AF too
CASTREXCosta Rica · Nov 18, 2008#12Hey, for anyone wondering how the Yaris long tube header looks....
Here you go! Richard just sent me the picture... 👍
🤤
1 attachment not included in this copy
cali yarisCanoga Park, CA · Nov 18, 2008#13😲 🤤
😳🤤🙇
richardholdenerThread starterLas vegas, NV · Nov 18, 2008#15Since this is a mass air management system, it has been very self compensating in terms of air/fuel and timing (we monitored via palm pilot), so no changes to ECU are necessary. Air fuel curve was basically same as stock. We think additional timing may help power since we were only registering a peak of 20-21 degrees (less in the mid range).
Originally Posted by
pinoypizzaboy ↑ im a noob but 20+ whp is a big change for the yaris ecu wont this require some management of some sort? this is almost the same gains as the blitz🙂
marcustoronto, canada · Nov 18, 2008#16interesting...
send it all please. this stuff is going to make me gutt my car.
PETERPOOPOahu · Nov 18, 2008#18almost shipping time
blacksandiegovitzJust chillin' out brah ! · Nov 18, 2008#19 Originally Posted by
PETERPOOP ↑ almost shipping time
OHHHHH Yes !
whooppee777Maryland · Nov 18, 2008#20 Originally Posted by
CASTREX ↑ Hey, for anyone wondering how the Yaris long tube header looks....
Here you go! Richard just sent me the picture... 👍
🤤
i'm confused. this will replace the mid pipe as well? would there really be a difference in power between this and say...the weapon R header that i have?
richardholdenerThread starterLas vegas, NV · Nov 18, 2008#21Th header you have is a replacement for the stock header-it (like the stock exhaust manifold) is too short to provide any scavenging effect. It is the scavenging effect that improves power, not simply additional flow.Basically the header must be tuned for the application. It can either fit in place of the stock exhaust manifodl or be tuned to improve the power-but not both. The long-tube header does require a different mid pipe which will be sold with the header.
Originally Posted by
whooppee777 ↑ i'm confused. this will replace the mid pipe as well? would there really be a difference in power between this and say...the weapon R header that i have?
bdc87Lake County, CA · Nov 18, 2008#22Now you need to take this to the track so we can get some 1/4mile and 60 times. 15.8?
justjesusOrange County · Nov 18, 2008#23Too bad they closed Palmdale (LA County Raceway)
Originally Posted by
bdc87 ↑ Now you need to take this to the track so we can get some 1/4mile and 60 times. 15.8?
pinoypizzaboylas vegas/ henderson · Nov 18, 2008#24 Originally Posted by
bdc87 ↑ Now you need to take this to the track so we can get some 1/4mile and 60 times. 15.8?
15.8 for a yaris thats crazzey. stock is like high 17s right?
PHXDEMONPhoenix, AZ · Nov 18, 2008#25I want one of those headers 🤤
blacksandiegovitzJust chillin' out brah ! · Nov 18, 2008#26 Originally Posted by
PHXDEMON ↑ I want one of those headers 🤤
If you really want one , please sign up for the long tube header Gb list. We only need 10 people...
CASTREXCosta Rica · Nov 18, 2008#27 Originally Posted by
pinoypizzaboy ↑ 15.8 for a yaris thats crazzey. stock is like high 17s right?
I pulled 15.85 on my Yaris with around 120 whp with some extra weight and heavy 17 rims. So that sounds about right.
richardholdenerThread starterLas vegas, NV · Nov 19, 2008#28How did you get 120 wheel hp from your yaris?
Originally Posted by
CASTREX ↑ I pulled 15.85 on my Yaris with around 120 whp with some extra weight and heavy 17 rims. So that sounds about right.
pinoypizzaboylas vegas/ henderson · Nov 19, 2008#29 Originally Posted by
richardholdener ↑ How did you get 120 wheel hp from your yaris?
he has 1.8 motor I think but high 15s for a 1.5 yaris is fast right?
bzinn 1University Place,WA · Nov 19, 2008#30WOW.......great work building all the materials to work together as you have put them.That in its self is hard to do at times and a lot of trial and error.
Now I gotta start saving as this could make a fun improvement at the track.
richardholdenerThread starterLas vegas, NV · Nov 19, 2008#31That would explain it. As indicated by the supplied grpah, despite nearly the same peak power, the 1.8L in the Xd and yaris TS offers more average power and will therefore accelerate quicker assuming similar weight and gearing.
Originally Posted by
pinoypizzaboy ↑ he has 1.8 motor I think but high 15s for a 1.5 yaris is fast right?
1 attachment not included in this copy
eTiMaGoBangkok, Thailand · Nov 19, 2008#32no replacement for displacement 😉
bdc87Lake County, CA · Nov 19, 2008#33I think stock 1.5L is 16.8. Remember reading this in R&T. It depends on the driver and variables but basic physics says 15.8-16 1/4 time.
dallasCanada · Nov 19, 2008#34Wow amazing gain for bolt on's, great work! What gear is the dyno run done in? I always thought that a tri Y header was better for scavenging and torque than a 4 into 1, yet this set up is impressive! 👍
.
Originally Posted by
richardholdener ↑ Th header you have is a replacement for the stock header-it (like the stock exhaust manifold) is too short to provide any scavenging effect. It is the scavenging effect that improves power, not simply additional flow.Basically the header must be tuned for the application. It can either fit in place of the stock exhaust manifodl or be tuned to improve the power-but not both. The long-tube header does require a different mid pipe which will be sold with the header.
dallasCanada · Nov 19, 2008#35Sorry I just found your great explanation of header types on the other thread!
whooppee777Maryland · Nov 19, 2008#36 Originally Posted by
richardholdener ↑ The long-tube header does require a different mid pipe which will be sold with the header.
that answers my question. thanks
PETERPOOPOahu · Nov 19, 2008#37What exhaust set up were you running for this dyno?
the long-tube header (also midpipe you will provide) and stock axleback? or the header/midpipe with the removal of the stock exhaust (running open exhuast manifold)? or the head/midpipe with the 2.5" exhaust
at3GGVA Beach · Nov 19, 2008#38i know something went "boom" when you were testing/troubleshooting/enjoying your proto turbo kit....any news on that?
YarisPRMayaWest, Puerto Rico · Nov 20, 2008#39 Originally Posted by
richardholdener ↑ The Xd throttle body is larger than the Yaris but it plugs right in and runs perfectrly on the yaris. Just needs a minute or two to idel down the first time you start it-ECU is not use to having such large throttl eopenings at idle but once this self adjustment takes place right after initial start up-it works perfectly and was worth roughly 2 hp at this power level. Intake will come with flange to accept Xd TB and have adapter plate to neck down for yaris TB.
Any chance u have any pics of the TB installed on the yaris?
richardholdenerThread starterLas vegas, NV · Nov 21, 2008#40The Xd TB was installed on the prototype intake-we won't have photos of the new intake until the production piece is ready. Externally, the Xd TB looks the same as the yaris.
Originally Posted by
YarisPR ↑ Any chance u have any pics of the TB installed on the yaris?
PETERPOOPOahu · Nov 21, 2008#41can you answer my question about which exhaust setup you were running for this dyno or did i miss it earlier in the post? 🤷
i'm hoping it was just the stock exhaust or axleback and not the removal of the stock exhaust.
richardholdenerThread starterLas vegas, NV · Nov 21, 2008#42The exhaust run witht he long tube header was a 2.25-inch section of tubing to simulate a free flowing system. We willmake the long tube and mid pipe connect to the stock or after market axle back, but best results will come with 2.25-inch (or larger) exhaust.
Originally Posted by
PETERPOOP ↑ can you answer my question about which exhaust setup you were running for this dyno or did i miss it earlier in the post? 🤷
i'm hoping it was just the stock exhaust or axleback and not the removal of the stock exhaust.
PETERPOOPOahu · Nov 21, 2008#43thanks!
4MPGmissouri · Dec 13, 2008#44Pretty impressive.. dammed near 25 percent increase in power with zero tuning and only boltons.
Is there no way to tune the car other than a complete standalone system? I can defiantly see where your loosing some power to the tune (especially the dips between 4200~ and 5500~).
I have seen (on this forum) where people did piston swaps from other Toyota cars to get a bump in compression, any plans to try this out on your test mule?
richardholdenerThread starterLas vegas, NV · Dec 13, 2008#45I am very curious to know how you see where we are losing power due to tuning based on the graph provided. Since there is no evidence of the air/fuel ratio or timing values, how do you know where tuning may improve the power? To answer your question about tuning, we will be employing an FIC on the yaris motor (basically to increase the timing-since air/fuel is near spot on already. No plans on changing compression-the test motor belongs to another forum member and we don't think he will like us tearing his motor apart. BTW-The dips in the curves you are refering to are a function of the resonance waves from the long-tube headers and intake manifold.
Originally Posted by
4MPG ↑ Pretty impressive.. dammed near 25 percent increase in power with zero tuning and only boltons.
Is there no way to tune the car other than a complete standalone system? I can defiantly see where your loosing some power to the tune (especially the dips between 4200~ and 5500~).
I have seen (on this forum) where people did piston swaps from other Toyota cars to get a bump in compression, any plans to try this out on your test mule?
4MPGmissouri · Dec 13, 2008#46 Originally Posted by
richardholdener ↑ I am very curious to know how you see where we are losing power due to tuning based on the graph provided. Since there is no evidence of the air/fuel ratio or timing values, how do you know where tuning may improve the power? To answer your question about tuning, we will be employing an FIC on the yaris motor (basically to increase the timing-since air/fuel is near spot on already. No plans on changing compression-the test motor belongs to another forum member and we don't think he will like us tearing his motor apart. BTW-The dips in the curves you are refering to are a function of the resonance waves from the long-tube headers and intake manifold.
Your seeing these kinds of dips etc due to the headers? The dyno sheets of the before/after of the headers really show some spots (4-5200) where it looked like a tuning issue, as it was present but not as exaggerated on the stock dyno, which I figured was a tuning issue. Its probably alot less important than it looks... on this scale every small change looks like a monster.
thebarberGrand Rapids, MI · Dec 13, 2008#47 Originally Posted by
4MPG ↑ Your seeing these kinds of dips etc due to the headers? The dyno sheets of the before/after of the headers really show some spots (4-5200) where it looked like a tuning issue, as it was present but not as exaggerated on the stock dyno, which I figured was a tuning issue. Its probably alot less important than it looks... on this scale every small change looks like a monster.
its not really a dip in the dyno, its just a flatter tq curve vs stock.....
richardholdenerThread starterLas vegas, NV · Dec 13, 2008#48My point is that the only way to determine if any dips in the power curve (HP or TQ) are caused by "tuning issues" is to compare the dips versus the air/fuel curve or the timing curve. This way you can determine if the dip is caused by a lean or rich mixture or by excessive or insufficient timing. Simply looking at dips in the power curve will not allow to to determine the reason they exist. As indicated previously, the dips in the power curve are caused by resonace tuning offered by the new induction and exhaust, not by air/fuel or timing. We know this because both air/fuel and timing curves remained identical before and after the header and/or intake installation (we always monitor both while dyno testing). This should clear everything up.
Originally Posted by
4MPG ↑ Your seeing these kinds of dips etc due to the headers? The dyno sheets of the before/after of the headers really show some spots (4-5200) where it looked like a tuning issue, as it was present but not as exaggerated on the stock dyno, which I figured was a tuning issue. Its probably alot less important than it looks... on this scale every small change looks like a monster.