auxmikeOriginal postLI, New Yawk · Nov 17, 2008#1The black steel cap one from PepBoys is awful and hops a lot. The Channel Locks work, but there's not really enough room in that area so you have to tilt the pliers down and that makes it real hard to get a good solid grip. The AST is an all aluminum casting and fits like a glove!🤘
Replies 20
stranCal · Nov 18, 2008#2i use the walmart oil filter wrench and that works fine. it's the same design except plastic and costs $2.
slvryarisIndiana · Nov 19, 2008#3I used one of these last time. I guess the torque spec on the filter is like screw on till it hits the top and then a 3/4 turn. The specs are in the service manual Thomas provided on here.
ROCKLAND TOYOTAROCKLAND COUNTY NY · Nov 19, 2008#4nice to see it fits the newer cartridge ones as well.....
bdc87Lake County, CA · Nov 19, 2008#5I use K&N filters it has a "nut" built in so it can be directly removed with a wrench.
ToddRNorthern IL · Nov 19, 2008#6 Originally Posted by
bdc87 ↑ I use K&N filters it has a "nut" built in so it can be directly removed with a wrench.
+1
TheSilkySmoothNew Hampshire · Nov 21, 2008#7 Originally Posted by
auxmike ↑ The black steel cap one from PepBoys is awful and hops a lot. The Channel Locks work, but there's not really enough room in that area so you have to tilt the pliers down and that makes it real hard to get a good solid grip. The AST is an all aluminum casting and fits like a glove!🤘
I have plastic unit for a couple bucks for doing my sister's car, How much is this piece? Would be C-O-L-D in winter!
TheSilkySmoothNew Hampshire · Nov 21, 2008#8BTW any one find a good source for drain plug washers like under 25c each? No way I'm paying dealer a 1 euro for a penny washer. Can you use brass from the hardware store? and are they 12 or 14 mm? Sorry for all the questions.
auxmikeThread starterLI, New Yawk · Nov 21, 2008#9 Originally Posted by
TheSilkySmooth ↑ I have plastic unit for a couple bucks for doing my sister's car, How much is this piece? Would be C-O-L-D in winter!
About $20USD.
auxmikeThread starterLI, New Yawk · Nov 21, 2008#10 Originally Posted by
TheSilkySmooth ↑ BTW any one find a good source for drain plug washers like under 25c each? No way I'm paying dealer a 1 euro for a penny washer. Can you use brass from the hardware store? and are they 12 or 14 mm? Sorry for all the questions.
I splurged and bought 10 washers for $10 from the dealer.
Penny wise and Pound foolish can cost you a lot in the end.....
🤷
Nexus1155Dorchester · Nov 21, 2008#11?????????? you know they sell this auto tightening chain wrench where you attach the links on the oil filter and then crank it... works on every one of our cars even when it is stuck on...
nemelekArizona · Nov 22, 2008#12 Originally Posted by
slvryaris ↑ I used one of these last time. I guess the torque spec on the filter is like screw on till it hits the top and then a 3/4 turn. The specs are in the service manual Thomas provided on here.
The factory oil filter had more torque than 3/4 turn. I have found that 3/4 to 1 turn works well and I am able to remove the old filter by hand.
Sodium DuckWestern Mass. · Nov 22, 2008#13 Originally Posted by
Nexus1155 ↑ ?????????? you know they sell this auto tightening chain wrench where you attach the links on the oil filter and then crank it... works on every one of our cars even when it is stuck on...
Interesting, never seen that before.
earljailBC, Canada · Nov 22, 2008#14 Originally Posted by
TheSilkySmooth ↑ BTW any one find a good source for drain plug washers like under 25c each? No way I'm paying dealer a 1 euro for a penny washer. Can you use brass from the hardware store? and are they 12 or 14 mm? Sorry for all the questions.
Well, they are "crush" washers, so they are special. If you want to be cheap, just reuse them. I do replace it each time on my Yaris, but I didn't used to with the other cars I've had.
gidNortheast · Nov 22, 2008#15I use the black socket for changes . Take some sticky back felt and put on the inside edges of oil filter socket to help slide on and off the oil filter . That way shouldn't need to use claws of hammer to get stuck socket off of oil filter which can damage it . Once is on , I'll tighten by hand and then turn oil filter with socket about 3/4 of a turn . Last , I pour 4 ounces of oil into new filter before reinstalling . The TOYO ( Denso ) oil filters already have a lubricant ( looks like vaseline ) on gasket . A good thing , no oily fingers .
ShroomsterOrlando · Nov 23, 2008#16 Originally Posted by
Sodium Duck ↑ Interesting, never seen that before.
just add little cutting wheels to the chain links and you have exhaust pipe cutters!!!
nsmitchellRichmond, VA · Nov 24, 2008#17Napa sells a good one as well. It fits the filters perfectly.
TheSilkySmoothNew Hampshire · Nov 27, 2008#18 Originally Posted by
auxmike ↑ I splurged and bought 10 washers for $10 from the dealer.
Penny wise and Pound foolish can cost you a lot in the end.....
🤷
Thats not pencewise - thats a ripoff. Its a goat-mule sacrifical drain plug washer not even remotely high tech. Boy, you americas throw your money away like its been given too you by rich daddy! Drive up coffe for three euro a cup and complain about gas cost. Very Hilarious! I'll save the buck and buy the next better grade OIL FILTER or Euro Oil where it may do something good for the motor. If you dig through garbage for food and cloth 1/2 your life you will not be so cavalier about throwing money away. So Brass washer, hot plunged in zinc or stannum will do great for "crush washer" So is it 14mm or 12 mm DIA?
auxmikeThread starterLI, New Yawk · Nov 27, 2008#19To each his own. 😁
TheSilkySmoothNew Hampshire · Nov 28, 2008#20 Originally Posted by
auxmike ↑ To each his own. 😁
Yeah, I like the toyota washer, Good for 3 uses at least, but a buck? I am still on the original after 4 OC and time for new, We used spark plug washers in europe but no parts guy seems to carry anymore. Maybe with advent of $$$ iridium-tip sprak plug the replacement washer will come back. On the spark plug you shouls ALWAYS putting on the new crush-washer if you pull a plug. I see many Subaru's with toasted heads from backed out plugs and reused washers.
back into the oil pan = Guys, just do not substitute with a zinc-dipped steel in the vintertyme - it will dissapear (rusting) if you getting the salz-wasser on it!
Sonja's bro
gidNortheast · Nov 28, 2008#21here's a car ramp D.I.Y. ( for gear , motor oil change , etc. ) , go to
http://s49.photobucket.com/albums/f2...t=IMG_1243.jpg . Could use 1 level for ramp instead of 2 ( plenty of clearance with 1 board ) . Then put 1 piece of wood across each end of board ( stoppers ) to prevent driving of ramp . Should take less than 1/2 an hour to cut and nail . This is from SCIONLIFE for an 1st generation XB , a cousin of the YARIS .