Yarisworld Archive

Paddle Shifting (for MT)

86 posts · 35,954 views · page 2 of 2

Replies continued

TamagoThread starterOff Grid · Dec 22, 2008#51
Originally Posted by Russelt3hPirate ↑
Looks good.

how easy would this be to install if the trans was already outside of the vehicle?
outside or inside?

i wouldn't risk having those lil cylinders bolted to the trans during the re-installation
Russelt3hPirateEpcot · Dec 22, 2008#52
good point, but I assume it'd be easier to setup outside the car, then bolt on the cylinders.
TamagoThread starterOff Grid · Dec 22, 2008#53
Originally Posted by Russelt3hPirate ↑
good point, but I assume it'd be easier to setup outside the car, then bolt on the cylinders.
this is how it was done :D

cylinders are not in right now, figured i'd give the trans a few days of shakedown before going to the air setup. stay tuned
Russelt3hPirateEpcot · Dec 22, 2008#54
Originally Posted by Tamago ↑
this is how it was done :D

cylinders are not in right now, figured i'd give the trans a few days of shakedown before going to the air setup. stay tuned
wuss, i thought you were going straight to sequential-style :D
TamagoThread starterOff Grid · Dec 22, 2008#55
Originally Posted by Russelt3hPirate ↑
wuss, i thought you were going straight to sequential-style :D
ever lifted a transmission in over your head by hand with no assistance?

🤷

or done an oilchange without help?

🤷

😳
Russelt3hPirateEpcot · Dec 22, 2008#56
Originally Posted by Tamago ↑
ever lifted a transmission in over your head by hand with no assistance?

🤷
sheesh. so touchy. 🤣


Originally Posted by Tamago ↑
or done an oilchange without help?

🤷
haha, a few times. Hell Abby did Russell's (The Yaris's) last oil change all by her lonesome. :)

Originally Posted by Tamago ↑
😳
😳
eTiMaGoBangkok, Thailand · Feb 4, 2009#57
so... any updates?
TamagoThread starterOff Grid · Feb 4, 2009#58
Originally Posted by eTiMaGo ↑
so... any updates?
no.. everything's on hold right now. i'm having some serious clutch issues (non paddleshift setup) so the trans will be coming down again as soon as i can afford an un-sprung disk. THIS TIME when it's out i'll get everything going. i'm really only short a few parts to complete but right now.. with the way money's been, i can't justify the cost 🙁
JerkrattFair Lawn, NJ · Feb 5, 2009#59
well now that i read this im going to check this thread out and see updates...
TheRealEnthMiami, FL · Apr 7, 2009#60
Dont worry Im going to make this happen =)
rob323Joyner, Brisbane · Apr 7, 2009#61
Love the ingenuity, wish I had the electronics background to be able to do this sort of stuff.
How do you control the throw if the pistons so that you don't overshift the gears? Do you have physical stops on the gearbox casing for this?
TamagoThread starterOff Grid · Jun 25, 2009#62
bumping this so people will yell at me to finish already lol. i still need a pressure switch and sort out my plumbing issues and i should be ready to get this thing done already :D
TamagoThread starterOff Grid · Jun 25, 2009#63
Originally Posted by rob323 ↑
Love the ingenuity, wish I had the electronics background to be able to do this sort of stuff.
How do you control the throw if the pistons so that you don't overshift the gears? Do you have physical stops on the gearbox casing for this?
the air cylinders themselves actually are of perfect stroke length :) i got lucky!
mrbondIllinois · Jun 25, 2009#64
Subscribed. I don't know how I didn't see this before.
Tamago, are you still planning a SMT setup with your shifter cage? Or what's the deal with that?
TamagoThread starterOff Grid · Jun 25, 2009#65
Originally Posted by mrbond ↑
Subscribed. I don't know how I didn't see this before.
Tamago, are you still planning a SMT setup with your shifter cage? Or what's the deal with that?
well i currently haven't come up with a plan for the actual paddles. for now i'm gonna use the stock shifter i have wired up. in the future though i'll def try to make some easy paddles :)
mrbondIllinois · Jun 25, 2009#66
For sure. Yeah, that's the one thing about the Fit I kinda like - the paddle shifting. But I don't like the idea that an automatic is required for that perk.
mrbondIllinois · Jun 25, 2009#68
naw. = fail x2. First, they're pretty unattractive. Second, they'd require so much modification to work with a real SMT setup that you're better off just machining really pretty pieces. The bracket miiiiiight be worth the cost...
TamagoThread starterOff Grid · Jun 25, 2009#70
Originally Posted by AlexNet0 ↑
Exactly what just popped into my head when I read the must recent posts. same item, lol. I personally have no idea how to do it, though.
i'd probably put microswitches in the joints where the ugly bolts hold the center to the paddles themselves..

hmm

tempted to buy :D
AlexNet0Rockland, ME · Jun 25, 2009#71
Originally Posted by Tamago ↑
i'd probably put microswitches in the joints where the ugly bolts hold the center to the paddles themselves..

hmm

tempted to buy :D
lol, I was thinking buy two of them (for 9.99 a piece with free shipping)
cut off the "paddles" that are on them, and space them by 1/8th inch so you have some room between to play with and still be able to bolt it on so your switches wont be exposed.
kngrsllSpartanburg, SC · Jun 25, 2009#72
you guys are insane LOL.

my only shifting mod was an extension and knob so i could shift faster (bc my hand has to move less distance if you dont follow)

I think even if i get a Ferrari F430, id rather have a manual box. I drove an M5 with paddles and i didnt like it and thats a pretty good system.
TamagoThread starterOff Grid · Jun 25, 2009#73
Originally Posted by PK198105 ↑
Tamago have you tested the PLC (what kind) for response time and delays? I would suspect your setup to require fast response time. Would it interest you to try and see if a micro controller could do a better job? And it would be easily upgradeable. Atmel has some good and inexpensive uCs

oh and would the paddles follow the steering a la F1 or be stationary ?
i'm pretty sure the PLC is up to the task, we'll see though! the paddles at this point will most likely move with the steering wheel :)
Nexus1155Dorchester · Jun 25, 2009#74
I can't wait to see this thing in action, but i don't know why anyone wouldnt have it F1 style, what if you need to upshift or downshift when turning who wants to have to move their hand back to a center position? lol I'm sure Tamago is smarter than that
cali yarisCanoga Park, CA · Jul 24, 2012#75
Picture not included in this copy
1.5Tampa · Jul 24, 2012#76
no more necromancer lol
cali yarisCanoga Park, CA · Jul 24, 2012#77
^ I play the card I think is needed. 😆
JerkrattFair Lawn, NJ · Jul 24, 2012#78
Do it!
mazillaSan Jacinto California · Jul 24, 2012#79
That video is pretty sweet, but that's a lot of hardware...
1.5Tampa · Jul 24, 2012#80
Originally Posted by panoramix3519 ↑
sory for my english but what is necromancer what do you mean?
is a claimed form of magic involving communication with the deceased

wikipedia

😆
CrankyOldManWest Michigan · Jul 25, 2012#81
Have any of you considered the MR2 spyder (sequential gearbox) steering wheel instead of adding paddles? Or for that matter, just shoehorning in the whole MR2 shift system?
cali yarisCanoga Park, CA · Jul 25, 2012#82
I have to say the video is pretty cool.
mazillaSan Jacinto California · Jul 25, 2012#83
Originally Posted by panoramix3519 ↑
this is the block of valves
http://imageshack.us/photo/my-images...mag0175hg.jpg/
this is the 5 cylinders
http://imageshack.us/photo/my-images/571/imag0176l.jpg/
and this is the logo with one expansion module
http://imageshack.us/photo/my-images/821/imag0179g.jpg/
thats all the hardware because i will put two wires to the stick at the same position with the two wires that the stick have now so i will move the stick and the stick will move the gearbox. The hardware is small and i can put it at the trunk in the room for the spare wheel so you cant see anything on the car.
and this is a screenshot from the program
http://imageshack.us/photo/my-images/196/imag0182m.jpg/

Great, thank you for the perspective shots...I didn't realize everything was the size of a lighter! 🎉
TamagoThread starterOff Grid · Nov 18, 2012#84
Originally Posted by CrankyOldMan ↑
Have any of you considered the MR2 spyder (sequential gearbox) steering wheel instead of adding paddles? Or for that matter, just shoehorning in the whole MR2 shift system?
that system is total garbage, and should have never been built.
TamagoThread starterOff Grid · Nov 22, 2012#85
No, i never did finish it. i sold the car it was supposed to go in, and moved on. I also sold the Siemens PLC.. many many years ago ;)
dmacnzMacau · Jan 31, 2014#86
Originally Posted by Tamago ↑
No, i never did finish it. i sold the car it was supposed to go in, and moved on. I also sold the Siemens PLC.. many many years ago ;)
Anyone else try this?!

Just ordered a PLC and some actuators!
Keen to give it a try!
Seems to be very limited info around!

Seems this is the only working system I can find!