Yarisworld Archive

PRM Jetstream Prototype CAI

81 posts · 23,797 views · page 2 of 2

Replies continued

MUSKOKA800Chatham, Ontario, Canada · Jan 12, 2009#51
Dyno'ing this intake on my sedan this evening.

WeeYari,
If you see this check your PM for details and make it if you can.
thebarberGrand Rapids, MI · Jan 12, 2009#52
no sleep until dynos are posted!

if youre there w/ some matrix guys, tell them thebarber says 'whats up'
TamagoOff Grid · Jan 12, 2009#53
Originally Posted by cali yaris ↑
The Fit one would give more gain; they have more to start with.
that's not how it works 😉

any gain is a ratio of restriction before and after the new part added.. if the FIT has a more restrictive intake than the yaris from the factory it'll show more gains. hondas benefit greatly from bolt-ons because they come with such restrictive intake/exhaust setups
WeeYariThread starterGeorgetown, Ontario, Canada · Jan 12, 2009#54
Dyno'd on MUSKOKAs sedan. Printed copy of chart won't scan in worth shit, but will have electronic version sent to me later.

In a nut shell:
- base line stock 97.15 whp/101.77 ft-lbs torque
- with intake 101.12 whp/104.07 ft-lbs torque

Graph shows nice even gains throughout the power curve.
thebarberGrand Rapids, MI · Jan 12, 2009#55
Originally Posted by WeeYari ↑
Dyno'd on MUSKOKAs sedan. Printed copy of chart won't scan in worth shit, but will have electronic version sent to me later.

In a nut shell:
- base line stock 97.15 whp/101.77 ft-lbs torque
- with intake 101.12 whp/104.07 ft-lbs torque

Graph shows nice even gains throughout the power curve.
not bad....4whp and 2.5tq....
ztrack157Biggs, CA · Jan 12, 2009#56
Where do I need to send my arm and leg
thebarberGrand Rapids, MI · Jan 13, 2009#57
lol, matrix guys saw you there last night too, eh?
MUSKOKA800Chatham, Ontario, Canada · Jan 13, 2009#58
Yes, a couple Matrix were tested prior to my Yaris.

Regarding the Yaris results;
If my baseline HP seems a bit higher than others results keep in mind that I had the TRD Axle-back in place. Otherwise no power-adders in place.
Also the OEM air filter element was put back in for the base-line test. I normally run with a K&N drop-in.
TamagoOff Grid · Jan 13, 2009#59
Originally Posted by WeeYari ↑
Dyno'd on MUSKOKAs sedan. Printed copy of chart won't scan in worth shit, but will have electronic version sent to me later.

In a nut shell:
- base line stock 97.15 whp/101.77 ft-lbs torque
- with intake 101.12 whp/104.07 ft-lbs torque

Graph shows nice even gains throughout the power curve.
that sounds like a seriously mis-calibrated dyno..

97whp on a STOCK AUTOMATIC 1nzfe that is rated at 106 AT THE CRANK??????? sorry, i call B.S.

edit: read that you had a muffler.. still isn't gonna make up for the 10 or so extra HP you show..
Thej3sta2Orlando, FL · Jan 13, 2009#60
/\ /\ /\ mmm so angry
TamagoOff Grid · Jan 13, 2009#61
Originally Posted by Thej3sta2 ↑
/\ /\ /\ mmm so angry
nah, it's just a mis-calibrated dyno.. either way, good numbers from the intake.. even if they aren't accurate
WeeYariThread starterGeorgetown, Ontario, Canada · Jan 13, 2009#62
Originally Posted by Tamago ↑
that sounds like a seriously mis-calibrated dyno..

97whp on a STOCK AUTOMATIC 1nzfe that is rated at 106 AT THE CRANK??????? sorry, i call B.S.

edit: read that you had a muffler.. still isn't gonna make up for the 10 or so extra HP you show..
First off, I can't speak to the calibration of the dyno, but regardless the difference between the two runs is where the meat lies.

Second, my HB is the automatic and served as the subject car for development. The sedan on the dyno last night is a 5 spd.
MUSKOKA800Chatham, Ontario, Canada · Jan 13, 2009#63
Originally Posted by Tamago ↑
that sounds like a seriously mis-calibrated dyno..

97whp on a STOCK AUTOMATIC 1nzfe that is rated at 106 AT THE CRANK??????? sorry, i call B.S.

edit: read that you had a muffler.. still isn't gonna make up for the 10 or so extra HP you show..
FYI, it's a 5 speed, not automatic. 🤷 And interesting because one of the Matrix guys was pissed, claiming his tested much higher on another dyno so???

In any case it's a know fact that no two dyno's will read the same. Different machine, different temps, different air, different operator...
The purpose of these tests were to compare baseline hp and that generated with the Jet Stream Intake installed. The pulls were accomplished within minutes of each other with only the time to switch the intakes between tests.
thebarberGrand Rapids, MI · Jan 13, 2009#64
ya, i saw the dyno for that xrs...was woefully low

yours makes some sense for a trd axle back and 5spd...5whp over stock doesnt seem too out of the range of plausibility for the yaris...

were you guys open to the outdoors? were the dyno's SAE corrected? how cold was it? likely about -10C and low humidity?

not bad gains though muskoka
MUSKOKA800Chatham, Ontario, Canada · Jan 14, 2009#65
Originally Posted by thebarber ↑
ya, i saw the dyno for that xrs...was woefully low

yours makes some sense for a trd axle back and 5spd...5whp over stock doesnt seem too out of the range of plausibility for the yaris...

were you guys open to the outdoors? were the dyno's SAE corrected? how cold was it? likely about -10C and low humidity?

not bad gains though muskoka
The shop doors were openned regularily to move vehicles about. Outside was likely about -3C that day. Humidity???. Inside the shop was around 17-18C. Can't comment on whether the dyno was SAE corrected. I was just there as a donor 5 speed car to test the intake. And for the experience.
thebarberGrand Rapids, MI · Jan 14, 2009#66
just sayin that if the dyno wasnt SAE corrected, itll run a few hp higher....but given the matrix guys were runnin low....but in 4th gear doesnt make sense to me

anyways, the key is in the difference over stock anyhow....so the PRM like most other intakes at a few hp and tq at the wheels over stock.....

sidebar: typically, the matrix guys use forrest and forrest racing in kitchener as their gospel. i dynoed my xrs in london one time and ran about 180whp while comparing 03 and 04 xrs ecu's. that was about 10whp higher than i ran at forrest and forrest. matrix guys wouldnt except 100whp/L, lol. so at any rate, i took it for what my test was originally for: and that was to compare power curves of 03 and 04 xrs ecu's....
WeeYariThread starterGeorgetown, Ontario, Canada · Jan 14, 2009#67
Originally Posted by thebarber ↑
anyways, the key is in the difference over stock anyhow....so the PRM like most other intakes at a few hp and tq at the wheels over stock.....
+1

Whether or not we are getting a 'true' whp reading for the Yaris here is not the point. This was a test to measure, back to back, the difference between two setups.
thebarberGrand Rapids, MI · Jan 14, 2009#68
have dyno sheet yet?
WeeYariThread starterGeorgetown, Ontario, Canada · Jan 14, 2009#69
Best I currently have is a crap scan. Had to play with colour hue to make both run lines visible.

Edit - 2008/01/18 new copy of graph received and is now shown.

1 attachment not included in this copy

thebarberGrand Rapids, MI · Jan 14, 2009#70
neato.
WeeYariThread starterGeorgetown, Ontario, Canada · Jan 14, 2009#71
Don't know how the xrs that was there felt about his numbers. Was interesting to see his results from 3 setups tho. I think these are the right numbers.

Stock 146.43 whp
AEM SRI 149.34 whp
AEM pipe + PRM filter 153.30 whp
thebarberGrand Rapids, MI · Jan 14, 2009#72
Originally Posted by WeeYari ↑
Don't know how the xrs that was there felt about his numbers. Was interesting to see his results from 3 setups tho. I think these are the right numbers.

Stock 146.43 whp
AEM SRI 149.34 whp
AEM pipe + PRM filter 153.30 whp
ya, thats low for an 03 xrs....usually dyno 157-ish stock....

here's mine from london
Picture not included in this copy
marcustoronto, canada · Jan 15, 2009#73
hope this group buy is under 150 canadian.. its a little pricy i think then again thats just me.
jetstreamertoronto · Jan 16, 2009#74
Maybe if there were oversea's pieces in this product.

These are all 100% U.S & Canadian Made !! Patented Unique Product !!

I have ten kits available to the first 10 respectable buyers at
a discounted rate.

if your interested please call-PM or e-mail me!

thanks for your patients!

gerry
905-939-2830
prm@look.ca
prmracing.com
thebarberGrand Rapids, MI · Jan 16, 2009#75
$?
jetstreamertoronto · Jan 16, 2009#76
$200.00 shipped.
WeeYariThread starterGeorgetown, Ontario, Canada · Jan 16, 2009#77
Gerry,

What colour silicones are available right now with these kits? I know you've got the blue and black, but are the red or yellow available now too?
thebarberGrand Rapids, MI · Jan 16, 2009#78
edit: maybe i can be a bit more constructive....

@ 200USD shipped (even in canada), i think there are better options for an intake
ztrack157Biggs, CA · Jan 18, 2009#80
Probably been asked before but I'm not looking through 5 pages of posts. Can we purchase just the filter.
WeeYariThread starterGeorgetown, Ontario, Canada · Jan 19, 2009#81
Originally Posted by ztrack157 ↑
Probably been asked before but I'm not looking through 5 pages of posts. Can we purchase just the filter.
I checked with Gerry and yes the filter can be bought seperately. Purchase would include filter + silicone reducer.

Email Gerry at prm@look.ca with any inquiries.