Yarisworld Archive

Full exhaust System for NA yaris

34 posts · 16,100 views

harveyjaiOriginal postSydney, Australia · Nov 7, 2008#1
Hi guys,

I just wanna know what would be the best combination of doing a full exhaust system for a NA yaris.

Atm, i have a bolt on muffler. I have read post saying Headers might not make too much difference. Also some of my mates told me to modify the cat or something.

What do u think is the best combination piping for a NA yaris? I wanna get the most out of my NA yaris...

I don't mine custom the whole thing, i just need some ideas.

Cheers,


Harvey😉

Replies 33

Thej3sta2Orlando, FL · Nov 7, 2008#2
Garm ( cali yaris ) sell a nitto midpipe that would work for clearing the farts out the rear end
harveyjaiThread starterSydney, Australia · Nov 7, 2008#3
Originally Posted by Thej3sta2 ↑
Garm ( cali yaris ) sell a nitto midpipe that would work for clearing the farts out the rear end
so that is a midpipe with a bolt on muffler that you are suggesting?
The ArchitectFL · Nov 7, 2008#4
DC 4-2-1 Header + Nitto Midpipe + Fujitsubo Wagolis = Yes ?
cali yarisCanoga Park, CA · Nov 8, 2008#5
^ ooh, nice
harveyjaiThread starterSydney, Australia · Nov 8, 2008#6
if we custom the whole thing, should we only use one cat? or? get rid of the cat? or?..
tk-421Dagobah · Nov 8, 2008#7
Originally Posted by The Architect ↑
DC 4-2-1 Header + Nitto Midpipe + Fujitsubo Wagolis = Yes ?
+1

I still haven't seen the DC 4-2-1 yet, but IMO 4-2-1 is the way to go for the Yaris. WSCP sells the W*R 4-2-1 header in case you're interested.
harveyjaiThread starterSydney, Australia · Nov 8, 2008#8
some of my friends have told me to get the 4-1 for yaris...any reason y?
if u keep u rev above 3K, 4-1 is better or 4-2-1?
tk-421Dagobah · Nov 8, 2008#9
Originally Posted by harveyjai ↑
some of my friends have told me to get the 4-1 for yaris...any reason y?
if u keep u rev above 3K, 4-1 is better or 4-2-1?
I've heard 4-1 is better for the higher range, and 4-2-1 is better for the lower/middle ranges.
CASTREXCosta Rica · Nov 8, 2008#10
Originally Posted by harveyjai ↑
some of my friends have told me to get the 4-1 for yaris...any reason y?
if u keep u rev above 3K, 4-1 is better or 4-2-1?
The DC header mentioned above is actually a 4-1 design. There is only one 4-2-1 header available for the Yaris and is from Weapon R.

In theory a 4-1 will provide a better gain and higher rpm while a 4-2-1 will provide better gains at the mid range. The problem is that by design the Yaris header is so short that I doubt there is much difference between any of the current model available. So I would tell you to choose the one that fits your budget!

If you want the ultimate set up and still keep it legal for emission testing I will tell you to get a high flow cat Only one or at least remove the secondary cat leave the primary cat. You already have a bolt on muffler so you just need the mid pipe.
If you can get mandrel bent tubing go for 2" pipe if you can't get it, then go for 2.25" pipe.
If you want it civil, snap a round mufller/resonator in the middle in place of the OE resonator and ou are good to go!

And the header will make some difference as long as you work out the rest of the muffler. Not much gain by mating a header with a stock exhaust.
tk-421Dagobah · Nov 8, 2008#11
Originally Posted by CASTREX ↑
The DC header mentioned above is actually a 4-1 design. There is only one 4-2-1 header available for the Yaris and is from Weapon R.

In theory a 4-1 will provide a better gain and higher rpm while a 4-2-1 will provide better gains at the mid range. The problem is that by design the Yaris header is so short that I doubt there is much difference between any of the current model available. So I would tell you to choose the one that fits your budget!

If you want the ultimate set up and still keep it legal for emission testing I will tell you to get a high flow cat Only one or at least remove the secondary cat leave the primary cat. You already have a bolt on muffler so you just need the mid pipe.
If you can get mandrel bent tubing go for 2" pipe if you can't get it, then go for 2.25" pipe.
If you want it civil, snap a round mufller/resonator in the middle in place of the OE resonator and ou are good to go!

And the header will make some difference as long as you work out the rest of the muffler. Not much gain by mating a header with a stock exhaust.
Interesting info! Thanks CASTREX 👍
t0m4sPanama · Nov 8, 2008#12
Originally Posted by CASTREX ↑
The DC header mentioned above is actually a 4-1 design. There is only one 4-2-1 header available for the Yaris and is from Weapon R.

In theory a 4-1 will provide a better gain and higher rpm while a 4-2-1 will provide better gains at the mid range. The problem is that by design the Yaris header is so short that I doubt there is much difference between any of the current model available. So I would tell you to choose the one that fits your budget!

If you want the ultimate set up and still keep it legal for emission testing I will tell you to get a high flow cat Only one or at least remove the secondary cat leave the primary cat. You already have a bolt on muffler so you just need the mid pipe.
If you can get mandrel bent tubing go for 2" pipe if you can't get it, then go for 2.25" pipe.
If you want it civil, snap a round mufller/resonator in the middle in place of the OE resonator and ou are good to go!

And the header will make some difference as long as you work out the rest of the muffler. Not much gain by mating a header with a stock exhaust.
i've heard that seddan 08 has 2 cats and there are 2 air sensors after each cat, when you do that mod above what r u gonna do with the sensors? it will not give u CE light?
i'm asking cuz i wanna do a mod almost like this
CASTREXCosta Rica · Nov 9, 2008#13
Originally Posted by t0m4s ↑
i've heard that seddan 08 has 2 cats and there are 2 air sensors after each cat, when you do that mod above what r u gonna do with the sensors? it will not give u CE light?
i'm asking cuz i wanna do a mod almost like this
Sedan = Liftback. The only difference is the axleback section. In the sedan is a little longer.

Both models come with 2 cat converters. First one just after the exhaust manifold and the other one a few inches after.
The car has 2 sensors on the exhaust the first one and the most important is in the header. You can not mess with that one. Then there is a second sensor right after the first cat. The function of that one is monitoring the functionality of the Primary (first) cat. That one can be easily tricked if you plan to go catless. There is no sensors after the second cat. Therefore you can remove that one if you want and your car won't even notice it.
t0m4sPanama · Nov 9, 2008#14
Originally Posted by CASTREX ↑
Sedan = Liftback. The only difference is the axleback section. In the sedan is a little longer.

Both models come with 2 cat converters. First one just after the exhaust manifold and the other one a few inches after.
The car has 2 sensors on the exhaust the first one and the most important is in the header. You can not mess with that one. Then there is a second sensor right after the first cat. The function of that one is monitoring the functionality of the Primary (first) cat. That one can be easily tricked if you plan to go catless. There is no sensors after the second cat. Therefore you can remove that one if you want and your car won't even notice it.
so when i change the header i just need to leave the sensor where it is and replace the header?
rob323Joyner, Brisbane · Nov 9, 2008#15
Originally Posted by harveyjai ↑
I have read post saying Headers might not make too much difference.
Do you have the 1.3 litre motor or the 1.5? Do the primaries on your stock headers have the collector down at the flange or only half way down?
CASTREXCosta Rica · Nov 9, 2008#16
Originally Posted by t0m4s ↑
so when i change the header i just need to leave the sensor where it is and replace the header?
Yes. You just need to unplug the sensor on the stock exhaust manifold. Take the manifold out and install the header and finally put te sensor back on the header. It should have a bung for the sensor. Pretty simple
harveyjaiThread starterSydney, Australia · Nov 11, 2008#17
Originally Posted by CASTREX ↑
The DC header mentioned above is actually a 4-1 design. There is only one 4-2-1 header ....

Cheers, that is some useful info there!👏
rob323Joyner, Brisbane · Nov 11, 2008#18
Do your stock headers look like these from a 1.3 litre Echo?
Picture not included in this copy

Or like these from a 1.5 litre Echo?
Picture not included in this copy

A guy on Ozecho has swapped the 1.5 litre manifold (the one with the longer primaries) onto his 1.3 litre and is happy with the improvement.
CASTREXCosta Rica · Nov 11, 2008#19
Us spec Yaris header is like this one

Originally Posted by rob323 ↑
Do your stock headers look like these from a 1.3 litre Echo?
Picture not included in this copy
rob323Joyner, Brisbane · Nov 11, 2008#20
Did you guys just get the 1.3 litre motor, or do you have those type of headers even on the 1.5 litre motors?
CASTREXCosta Rica · Nov 11, 2008#21
The only engine available in the US is the 1NZ-FE (1.5L)

You should be aware that there are some differences on external components between the 1.5L on the first gen Yaris/echo and the second gen yaris.

The intake for example is different. The exhaust manifold (header) is very similar between the 2 but there is a slight difference. So a first gen 1.5 yaris/echo header won't fit into a Second gen Yaris unit.


If you are looking for a header option for a first gen Yaris/echo, then you should look for the first gen scion xB and xA headers. Those will fit onto a first gen Yaris.
rob323Joyner, Brisbane · Nov 11, 2008#22
😉 What I was alluding to was that if the 1.5 Yaris came with a similar longer primary header than the 1.3 litre Yaris (as it did in the Echo), then that may be a cheaper option for the OP to look into instead of an aftermarket one.

I have a stack of assorted Echo parts, sadly no Yaris bits though to be able to thoroughly compare them.
harveyjaiThread starterSydney, Australia · Nov 14, 2008#23
so...back to topic..

Therefore my setup would be 4-1 Headers ----> single cat--->mid pipe-->bolt on muffler?
CASTREXCosta Rica · Nov 14, 2008#24
yeap!

😉
harveyjaiThread starterSydney, Australia · Nov 15, 2008#25
cheers,

just one more thing, wht that coating that u put on the headers that can smoothen the air flow inside? Would it be better if i do that instead of getting a new header?
YodaFL · Nov 15, 2008#26
so i thought the header would give like 1 +whp. thats what i read a while back pre hack. does the mid pipe help that much? what can the expected gains be? and does it work with an axle back exhaust
CASTREXCosta Rica · Nov 15, 2008#27
Originally Posted by harveyjai ↑
cheers,

just one more thing, wht that coating that u put on the headers that can smoothen the air flow inside? Would it be better if i do that instead of getting a new header?
You probably are talking about a ceramic coating. A ceramic coating can be applied on the outside, inside or both of an exhaust manifold or header. The function of the ceramic coating is to contain the heat within the pipe. Is not used to smooth anyting out.
Yes is useful, the DC header comes pre-coated, but the idea is to minimize the heat disipation thru the pipe.

Originally Posted by Yoda ↑
so i thought the header would give like 1 +whp. thats what i read a while back pre hack. does the mid pipe help that much? what can the expected gains be? and does it work with an axle back exhaust
I don't think that no one has made so far any intensive back to back dyno testing of Yaris exhaust components.
There are no back to back testing of the different header options or how they work along with other exhaust modifications. So any answer to your question will be mostly expeculation.

So all the comments you hear come from personal opinions (butt dynos).
harveyjaiThread starterSydney, Australia · Nov 15, 2008#28
ceramic coating..
Thats it!!

Would you apply them on everything?
or would it only be worth it to apply on headers?..umm..
richardholdenerLas vegas, NV · Nov 16, 2008#29
Just a note for this post-I am testing the true long-tube header on the Yaris today. If it works well, we plan on making a long-tube and complete 2.25-inch mid pipe exaust to go from header to axle back. We will also make an off-raod pipe to mate the stock shorty header to this exhaust as well. I'll post as sonn as we have dyno results.
eTiMaGoBangkok, Thailand · Nov 16, 2008#30
now that's an awesome idea, richard 🙂 fingers crossed!
at3GGVA Beach · Nov 16, 2008#31
Richard just keeps it coming...
CASTREXCosta Rica · Nov 16, 2008#32
Originally Posted by harveyjai ↑
ceramic coating..
Thats it!!

Would you apply them on everything?
or would it only be worth it to apply on headers?..umm..
I will say only the header... you will have a hard time coating the rest of the exhaust as most of the ceramic coatings need some time in the oven to cure...
t0m4sPanama · Nov 22, 2008#33
Castrex, in your t-sport that's a round muffler magnaflow 5 inches?
SpadesOregon,USA · Nov 23, 2008#34
custom is the way to go IMO, and if you delete the cats be sure to get a O2 simulater or build one with the proper ohm resistor.

i am running a custom catback set up...under $200US for everything. I have pics in my garage of part of the pipe work.