Bob_VTOriginal postVermont · Oct 29, 2008#1This has me stumped.
Outside temperature is 30 degrees..... I am using a scan gauge II.
Flat ground with cuise at 55 mph the water temperature is always at 184 degrees. Today since the weather was chilly...... I fllied the heat on at my feet , turned the temp dial to max hot and the fan on 1....... The water temperature goes up to 186 degrees.
I flipped the fan on and turned it off for a few minutes and the temp goes down to 184 but with the fan on it goes up to 186.
I'm stumped. I though turning on the heat would lower the water temperature not raise it?
Replies 11
marcustoronto, canada · Oct 29, 2008#2well by using ur fan ur using more energy isnt it..and that will make the engine run hotter due to more work need to be done... thats just me but i could be wrong..
Bob_VTThread starterVermont · Oct 29, 2008#3 Originally Posted by
marcus ↑ well by using ur fan ur using more energy isnt it..and that will make the engine run hotter due to more work need to be done... thats just me but i could be wrong..
I have considered that and I will test it using the stereo next.
ozmddDFW, TX · Oct 30, 2008#4The fan should draw considerably more load than the stereo, unless you have aftermarket, I would think. What happens when you leave the fan on but switch the temp to cold (not diverting any coolant to the heater core)? Other than the fact that you freeze?
Bob_VTThread starterVermont · Oct 30, 2008#5 Originally Posted by
ozmdd ↑ The fan should draw considerably more load than the stereo, unless you have aftermarket, I would think. What happens when you leave the fan on but switch the temp to cold (not diverting any coolant to the heater core)? Other than the fact that you freeze?
Great idea.... will try it.
Reddog99SoCal (Jamul) · Oct 30, 2008#6A two degree fluctuation on a 186 deg. reading is about 1%, which is probably less than the accuracy capability of the sensor. Small voltage changes could also cause the fluctuation. Nothing to worry about.
Bob_VTThread starterVermont · Oct 30, 2008#7Okay I tried it. When the heat gets turned on the temp gauge goes up to 186 on flat ground at a steady 50 mph. Turn the heat off and it drops to 184.
I have been giving this some thought. With the heat on there is more "system" for the heat and it retains a higher temperature. With the heat off there is a faster cooling enabled (a shorter path for the antifreeze) cooling it quicker.
This is all of course valid IF the Scan Gauge and the sensors are that accurate...... +/- a few degrees will not cook an engine.
ddongbaphay · Oct 31, 2008#8Is that heat with the AC button on?
talnlnkySpokane, Wa · Oct 31, 2008#9yeah... you don't know how the termastat is working... or not working... a giant factor in how your car controls its temp.
Bob_VTThread starterVermont · Oct 31, 2008#10 Originally Posted by
ddongbap ↑ Is that heat with the AC button on?
no
GeneWPennsylvania · Nov 1, 2008#11 Originally Posted by
Bob_VT ↑ This has me stumped.
Outside temperature is 30 degrees..... I am using a scan gauge II.
Flat ground with cuise at 55 mph the water temperature is always at 184 degrees. Today since the weather was chilly...... I fllied the heat on at my feet , turned the temp dial to max hot and the fan on 1....... The water temperature goes up to 186 degrees.
I flipped the fan on and turned it off for a few minutes and the temp goes down to 184 but with the fan on it goes up to 186.
I'm stumped. I though turning on the heat would lower the water temperature not raise it?
We could be seeing an artifact of some temperature control that gives higher priority to the internal heater and then lets the radiator cope with the excess. I dimly recall such a system in some GM cars in the past.
Basically the radiator does a more efficient job at cooling, so it drops the temps down to 184. When the heater is turned on it is not as efficient and since it gets higher priority than the radiator, the net effect is to run slightly hotter.
Gene
stranCal · Nov 3, 2008#12I came up with a good explanation.
The temperature of coolant is controlled by a mechanical thermostat independent of the rest of the car. The thermostat is not hooked up to the ECU or anything else so it would not know whether your heat is on or not. However, the temperature sensor is not necessarily next to the thermostat. In fact, base on BobVT observation, the setup must be like this:
temp sensor ---> heater core ---> thermostat ---> engine
Turning on the heater cools down the coolant. The thermostat will open more to compensate, hence increasing the temp at the sensor. This explains the phenomenon.