It took me less than 5 mins, seriously, to take this out. Three screws, pop off panel and unplug the relay/box. (I left my little box in the OEM location, just unplugged it.)
- DISABLED DayTime Running Lights How To- 2007 Yaris! -
265 posts · 199,488 views · page 4 of 6
Replies continued
my car is left side driven.Originally Posted by CTScott ↑It definitely can't be turned off by the computer, as it is a completely stand alone device.
Is your car right hand or left hand drive?
thanks.
Originally Posted by Kaya B. ↑my car is left side driven.
thanks.
In that case, the running light relay module should be located in the same place as the picture below. The running light module is the black box to the right of the steering column with the brown and white label.

I think they cause more issues. I have seen a Yaris twice now, with the day times on and no tail lights at night. I stopped one and said, your lights are not on. lol She said, yes they are, I said NO, they are the daytime lights, you have to turn the headlight switch. 😆
Yes,
I found the relay. It's different from yours :(
My car is Left side driven 2010 Yaris LS(Canadian Model)
The relay is under the (i don't know how to say in English.) place for putting personal things. at the right side (passenger side) near the air condition air filter. it is at the right side under the passenger airbag cancelattion button.
when i unplug the wires the headlights never on. if i turn the lights on or off...
your part number is 82810-52040 but mine is 82810-52060 :(
so i have to plug it back to power headlights :(
(sorry for my bad English.)

I found the relay. It's different from yours :(
My car is Left side driven 2010 Yaris LS(Canadian Model)
The relay is under the (i don't know how to say in English.) place for putting personal things. at the right side (passenger side) near the air condition air filter. it is at the right side under the passenger airbag cancelattion button.
when i unplug the wires the headlights never on. if i turn the lights on or off...
your part number is 82810-52040 but mine is 82810-52060 :(
so i have to plug it back to power headlights :(
(sorry for my bad English.)


Glovebox or glove compartment.Originally Posted by Kaya B. ↑(i don't know how to say in English.) place for putting personal things.
(I doubt a lot of them get used mainly for carrying gloves, though.)
I think there is something different to disable the daytime running lights in the Canadian models. It is federal law that the lights must be on at all times, and I am sure that is why there is a different box to control them.Originally Posted by Kaya B. ↑Yes,
I found the relay. It's different from yours :(
My car is Left side driven 2010 Yaris LS(Canadian Model)
The relay is under the (i don't know how to say in English.) place for putting personal things. at the right side (passenger side) near the air condition air filter. it is at the right side under the passenger airbag cancelattion button.
when i unplug the wires the headlights never on. if i turn the lights on or off...
your part number is 82810-52040 but mine is 82810-52060 :(
so i have to plug it back to power headlights :(
(sorry for my bad English.)
Originally Posted by Kaya B. ↑Yes,
I found the relay. It's different from yours :(
My car is Left side driven 2010 Yaris LS(Canadian Model)
The relay is under the (i don't know how to say in English.) place for putting personal things. at the right side (passenger side) near the air condition air filter. it is at the right side under the passenger airbag cancelattion button.
when i unplug the wires the headlights never on. if i turn the lights on or off...
your part number is 82810-52040 but mine is 82810-52060 :(
so i have to plug it back to power headlights :(
(sorry for my bad English.)
I found the 82810-52060 DRL module listed in the parts catalog from Japan. I have the wiring diagram for it, as well. It is wired into the car a little bit differently from the one on our US cars.
Looking at the wiring diagram, I believe that you can disable the daytime running lights, but still have the headlights function correctly by cutting the blue wire, which is next to the violet wire. After cutting the wire, you would need to tape or wire cap the two ends.
If you try it, cut it about 5 cm from the blue connector, to leave enough to reconnect it, if it doesn't work (Although, I am fairly confident that it will work).

thank you. i just cut the blue wire today and nothing changed :(Originally Posted by CTScott ↑I found the 82810-52060 DRL module listed in the parts catalog from Japan. I have the wiring diagram for it, as well. It is wired into the car a little bit differently from the one on our US cars.
Looking at the wiring diagram, I believe that you can disable the daytime running lights, but still have the headlights function correctly by cutting the blue wire, which is next to the violet wire. After cutting the wire, you would need to tape or wire cap the two ends.
If you try it, cut it about 5 cm from the blue connector, to leave enough to reconnect it, if it doesn't work (Although, I am fairly confident that it will work).
Attachment 30985
so i put the blue wire back :(
When you say nothing changed, do you mean that the running lights still remained on?Originally Posted by Kaya B. ↑thank you. i just cut the blue wire today and nothing changed :(
so i put the blue wire back :(
yes, daytime running lights are still on :(Originally Posted by CTScott ↑When you say nothing changed, do you mean that the running lights still remained on?
OK. Do you have a volt meter? That pin is definitely the one that controls turning the running lights on or off. For the US version of that module, letting that pin float (cutting the wire) works. For your version, if we can measure the voltage from the blue wire to the chassis ground with the engine running and with the headlights off and then with them on, we can figure out if that pin needs to be tied high or low on your module.Originally Posted by Kaya B. ↑yes, daytime running lights are still on :(
yes, thats already in my mind. i'll check the pins with voltmeter.Originally Posted by CTScott ↑OK. Do you have a volt meter? That pin is definitely the one that controls turning the running lights on or off. For the US version of that module, letting that pin float (cutting the wire) works. For your version, if we can measure the voltage from the blue wire to the chassis ground with the engine running and with the headlights off and then with them on, we can figure out if that pin needs to be tied high or low on your module.
but i'm back from holiday i don't know when can i find time to try :(
thanks for everything. i'll give information again when i'm done.
I found some more info in the European service manual. The wire I had you clip gets grounded when the headlight switch is turned on, to tell the module to stop the DRL mode.Originally Posted by Kaya B. ↑yes, thats already in my mind. i'll check the pins with voltmeter.
but i'm back from holiday i don't know when can i find time to try :(
thanks for everything. i'll give information again when i'm done.
One more quick test you could try is to take the DRL module side of the wire you cut (and then reattached) and connect it to a chassis ground.
does anyone know if this works on 2010 hb?
lol, nvm, read back a bit and saw we are still working on it
Your Canadian one may be the same as the US ones were prior to 2010 (which means that the procedure from the beginning of this thread would work). If it's the same as the European one, then as we saw with Kaya B's, this procedure wouldn't work.Originally Posted by yaris2010RS ↑does anyone know if this works on 2010 hb?
jsut a thought to consider...the DRL will stay off if the hand break is up..... maybe if we can confuse the relay into believing it is up all the time.... i studying electro-mechanical engineering in school so if you could send me a wire schematic maybe i can be of some assistance?
If the brake up works, then you definitely have the US style DRL module, as the European one doesn't have a parking brake switch input. In that case, the simple method will work for you...Originally Posted by yaris2010RS ↑jsut a thought to consider...the DRL will stay off if the hand break is up..... maybe if we can confuse the relay into believing it is up all the time.... i studying electro-mechanical engineering in school so if you could send me a wire schematic maybe i can be of some assistance?
SICK!!! that is god like, so glad dont have to rewire my entire car..... lol. GREAT SUCCESS!!! lol. thanks alot, gonna do it now. so its on the driverside (left side) of radio and best way to get to that plug is through the steering wheel
Yes, removing the lower column cover gives the quickest access to it.Originally Posted by yaris2010RS ↑SICK!!! that is god like, so glad dont have to rewire my entire car..... lol. GREAT SUCCESS!!! lol. thanks alot, gonna do it now. so its on the driverside (left side) of radio and best way to get to that plug is through the steering wheel
okay, successfully disabled them, thanks alot. anyone interested in buying the item off me i'm willing to sell. very easy to install/remove.
also disabled clutch position starter sensor thingy.... i found it very annoying as i liuke to start my car without fully getting in and depressing the clutch all the way past floorboards, through firewall as the car will onyl start once the clutch is in the engine compartment.....or at least thats how it feels.....
also disabled clutch position starter sensor thingy.... i found it very annoying as i liuke to start my car without fully getting in and depressing the clutch all the way past floorboards, through firewall as the car will onyl start once the clutch is in the engine compartment.....or at least thats how it feels.....
How? Did I miss a DIY for that?
lmfao, i've had the car for 3 days and i found it very annoying..... i can give u a quick run down of it.....
get down on the floor inside drivers area, look at the clutch, there is a white push button sensor. there isn't much room to work and i had learned from previous sensor bypasses that some sensors have a resistor inside so the computer knows if u cut the wires and connect them so i didn't even attempt that. and the darn thing is put in with like 3 tons tourque so u get unbolt it either. so, as i did, wrap it with duct tape. lol. not very technical and jsut a quick fix for now till i can get the time asside to do a proper job. (prob this weekend and if i actually do a good job i'lll DIY it)
get down on the floor inside drivers area, look at the clutch, there is a white push button sensor. there isn't much room to work and i had learned from previous sensor bypasses that some sensors have a resistor inside so the computer knows if u cut the wires and connect them so i didn't even attempt that. and the darn thing is put in with like 3 tons tourque so u get unbolt it either. so, as i did, wrap it with duct tape. lol. not very technical and jsut a quick fix for now till i can get the time asside to do a proper job. (prob this weekend and if i actually do a good job i'lll DIY it)
hey, i still couldn't take a look :( actually it's perfect in winter :)
my drl works while handbrake is on or off :( and the authorized service says "never ever don't cut any wires for warranty void" 😁
i'm happy i didn't cut the blue wire. i had just unplugged it from the connector because of the dispossibility of cancellation. so i put it back to the connector 😁
i think i'll go to a good electric technician and will give a try...
my drl works while handbrake is on or off :( and the authorized service says "never ever don't cut any wires for warranty void" 😁
i'm happy i didn't cut the blue wire. i had just unplugged it from the connector because of the dispossibility of cancellation. so i put it back to the connector 😁
i think i'll go to a good electric technician and will give a try...
The more I look at the EWD for the European version of the DRL module, the more amazed I am about how different it is than ours.Originally Posted by Kaya B. ↑hey, i still couldn't take a look :( actually it's perfect in winter :)
my drl works while handbrake is on or off :( and the authorized service says "never ever don't cut any wires for warranty void" 😁
i'm happy i didn't cut the blue wire. i had just unplugged it from the connector because of the dispossibility of cancellation. so i put it back to the connector 😁
i think i'll go to a good electric technician and will give a try...
One other quick thing that you can try is unplugging the green wire in pin 8 (the green wire next to the brown wire). This wire is the input from the alternator that tells the DRL module that the engine is running. With it removed, the DRL will think that the engine is not running and therefore won't waste the power to run the DRLs.

Done and awesome!!!
Thanks for info.
did that just now i love it :D i to will try to find a way of making this a perm fixOriginally Posted by yaris2010RS ↑lmfao, i've had the car for 3 days and i found it very annoying..... i can give u a quick run down of it.....
get down on the floor inside drivers area, look at the clutch, there is a white push button sensor. there isn't much room to work and i had learned from previous sensor bypasses that some sensors have a resistor inside so the computer knows if u cut the wires and connect them so i didn't even attempt that. and the darn thing is put in with like 3 tons tourque so u get unbolt it either. so, as i did, wrap it with duct tape. lol. not very technical and jsut a quick fix for now till i can get the time asside to do a proper job. (prob this weekend and if i actually do a good job i'lll DIY it)
Are drl's fog lights or part of the main light house?
They are the actual headlight bulbs, pulsed to be a bit less bright and hence prolong bulb life.Originally Posted by swidd ↑Are drl's fog lights or part of the main light house?
can the removed module be installed on headlights with no DRL?
Not easily, as there are quite a few wiring differences between cars built with an without DRLs.Originally Posted by fratzica ↑can the removed module be installed on headlights with no DRL?
I picked up my 2010 3 door HB last week, 6 months old w 4600 miles and found this wonderful site. Lots of helpful info. I've been thinking about several DIY mods: removing the DRL & maybe the back Toyota name. But , Saturday I checked and I have no DRL. DO you think the first owner did the disabling? As I don't want it anyway I'm probably not going to do anything.
The car came with most packages & options, but I was disappointed yesterday to discover it does not have adjustable intermittent wipers, only fixed one speed. That should be standard. Is it something that could be added?
The car came with most packages & options, but I was disappointed yesterday to discover it does not have adjustable intermittent wipers, only fixed one speed. That should be standard. Is it something that could be added?
DRLs were eliminated on 2010's.Originally Posted by Steveh27 ↑I picked up my 2010 3 door HB last week, 6 months old w 4600 miles and found this wonderful site. Lots of helpful info. I've been thinking about several DIY mods: removing the DRL & maybe the back Toyota name. But , Saturday I checked and I have no DRL. DO you think the first owner did the disabling? As I don't want it anyway I'm probably not going to do anything.
The car came with most packages & options, but I was disappointed yesterday to discover it does not have adjustable intermittent wipers, only fixed one speed. That should be standard. Is it something that could be added?
For the true intermittent wiper piece, check out this thread for a DIY on replacing the stalk, with a Prius one.
DIY - Liftback Intermittent Wipers via Stalk Replacement (v2.0)
Wow, thanks for the info. I'm happy about the no DRL. The manual says how it works 'if equipped'.
The wiper mod looks simple. But, I'm having trouble finding a low price like you got. Will call some junk yards maybe. The online dealer price was about $148.
The wiper mod looks simple. But, I'm having trouble finding a low price like you got. Will call some junk yards maybe. The online dealer price was about $148.
not in any canadian yaris 🙂Originally Posted by CTScott ↑DRLs were eliminated on 2010's.
OK - Good to know. For US Yaris elimination of DRL is listed in the "New Car Features" for 2010. The Canadian ones still having them explains them still being documented as "if equipped" in the 2010 EWDs.Originally Posted by yaris2010RS ↑not in any canadian yaris 🙂
Disconnected DRL, is there a way to make the stock fogs work now?
ur gonna have to put the module back in and only cut the big blue wire.
i personally opened mine up and cut a chunk out of the internal wires
i personally opened mine up and cut a chunk out of the internal wires
dont cut the wire..just pull it out just need small flat screw driver..
u can pull it out??😲 lol, y was i never told this?Originally Posted by marcus ↑dont cut the wire..just pull it out just need small flat screw driver..
always trust the pull out method 👍
yah you can i was about to cut it then notice the drl box just slides out and just by looking at the blue wire you can insert a small flat screw driver on the side and itll slide right off..Originally Posted by yaris2010RS ↑u can pull it out??😲 lol, y was i never told this?
always trust the pull out method 👍
Sorry,Originally Posted by CTScott ↑The more I look at the EWD for the European version of the DRL module, the more amazed I am about how different it is than ours.
One other quick thing that you can try is unplugging the green wire in pin 8 (the green wire next to the brown wire). This wire is the input from the alternator that tells the DRL module that the engine is running. With it removed, the DRL will think that the engine is not running and therefore won't waste the power to run the DRLs.
Attachment 31197
Once I tried; i pinned out wrong cable :( It didn't worked.
Then I didn't have enough time to try it. New marriage, new house, moving, holidays and lots of works.
I will try in the following days and give my reply. Thanks for your helps.
I finally disabled on my 2010 canadian model.
I cut the green wire coming from the alternator and another gray wire coming from the alternator. I'll take photos tomorrow about which cables i cut.
I cut the green wire coming from the alternator and another gray wire coming from the alternator. I'll take photos tomorrow about which cables i cut.
finally,
here is the schema.
here is the schema.

I've had my Yaris only 2 weeks now, and am so happy to get the info on how to disconnect the damn DRL's! Just last evening, upon arrival home from a 25 mile freeway drive, as I pulled into my garage I realized I had been driving on the DRL's, and of course no tail lights. Hey I know it is a supposed saftey issue but in my case not so much!
My Toyota service manager I called was only good for telling me there was NO way to disable them, HA!
My Toyota service manager I called was only good for telling me there was NO way to disable them, HA!
I didn't read every page...but I truly feel the DRL setup in this car is dangerous! The DRL's are bright enough to lead the way at night, which allows you to drive off without your tail lights on at night, especially because the speedo lighting looks fine w/o the headlights turned on.
cheers!
cheers!
quick question before I go ahead and do this... can that relay be re-installed just in case?
Hi all
DRLs are required by law on all Canadian cars as of the 1990 model year and newer. So if you disable them you could get a ticket.
Transport Canada did testing in the middle 1970's and from the data collected at that time concluded that you had a 30% less chance of having an accident in the daytime if everyone had DRLs. Just for your information.
Roy
DRLs are required by law on all Canadian cars as of the 1990 model year and newer. So if you disable them you could get a ticket.
Transport Canada did testing in the middle 1970's and from the data collected at that time concluded that you had a 30% less chance of having an accident in the daytime if everyone had DRLs. Just for your information.
Roy