Yarisworld Archive

DIY - Sparco Race Seat Install

17 posts · 55,429 views

IdjiitOriginal postHolly Springs, NC · Apr 30, 2006#1
Sorry I didn't do a full step-by-step on this one, but I was short on time. The procedure is fairly straight forward, but let me know if you've got any questions. For details on removing the stock seats and related info, go here: Front Seats - a bit of bad news...

The Sparco brackets had to be raised a bit to get clearance over the slider bolts - this isn't absolutely necessary, but if you don't do it the seat will be about a half inch, maybe an inch off center (to the left of the steering column). I can afford the space, so I went ahead and did it "right".

This was done by removing the stock seat from the stock slider rails, and using the rails/seat base as the base for the Sparco. I used flat steel stock to create some cross-bracing. Steel L-stock was used to attach the receiving side of the seatbelt.

There's a couple caveats with this solution:

A) It's heavy. As noted earlier the stock setup is 37lbs - the Sparco setup is 34lbs. Not a big savings. This is a combination of things - the stock seat base is heavy, and the metal cross braces I used are quite heavy since I used the heaviest gauge steel I could find.
B) It's not very clean looking. Keep in mind that the seat in relation to the base is offset to the right about 3 inches, so with the narrow Sparco base it's inevitable that you're going to see all the hardware. A fixed base setup would look much cleaner.
C) Ideally 2 screws would be used for each side of the cross braces to increase strength, but this would most likely require welding, which is outside my skillset.

Underside, showing cross-braces:
Picture lost · www.swiftbennett.com

Closeup of part of seatbelt sensor. Not sure if this is just detected whether the seatbelt is attached, or if it's also measuring weight on the steel (measuring difference in resistance in "empty" vs. "seated"? I'm not sure - I know the passenger side detects weight, I'm not sure about the driver's side):

Picture lost · www.swiftbennett.com

The plug that attaches to the car itself:
Picture lost · www.swiftbennett.com

Side view showing how far the slider mechanism protrudes. I could have had this further back by using a different set of screw on the slider rails, but it would have meant that I had more rail at the back protruding into the passenger area, which I need for the storage setup I have planned:
Picture lost · www.swiftbennett.com

Belt L-bracket before painting - note that the seat at this point is moved forward on the rails. Normally the back of the L-bracket would be flush with the back of the seat base:
Picture lost · www.swiftbennett.com

Detail of L-bracket, which is mounted underneath cross-braces. This corresponds with extra height on the left side, do to the slider-release mechanism, although it's a bit thicker than it should be, I may add washers to the other side later, but you certainly can't feel the difference:
Picture lost · www.swiftbennett.com

Installed - note that the belt has been looped through the seat so it's taught against my belly (I'm 6', 140lbs - if you're bigger you may not need to do this):
Picture lost · www.swiftbennett.com

Close Up of the exposed slider bracket. Sorry, no OEM look here...
Picture lost · www.swiftbennett.com

From the Outside:
Picture lost · www.swiftbennett.com

All told with this setup, I can go as low as 3 inches below stock. I currently have it at 2 1/2 inches, but I think I'll either tilt the front up slightly or bring the whole thing up 1/2 an inch. The unfortunate thing is that you're really limited by the angle of adjustment on the steering wheel. If you had it down 3 inches you'd really have to reach up to get to the steering wheel, which is a bit awkward.

Replies 16

why?harnett county NC · May 3, 2006#3
Those look good as well, I wonder how much they weigh.
SophieSleepsMA · May 24, 2006#4
I dunno if I would just bolt those flat steel pieces in.
In an accident I don't think it'd hold up all that great.

How about welding in some supports?
Running the flat steel across the seat seems like over time it would warp. One of my friends modified his jeep seats in a similar fashion and he needs to take them out and bend them back every once in a while.
IdjiitThread starterHolly Springs, NC · May 25, 2006#5
Originally Posted by SophieSleeps
I dunno if I would just bolt those flat steel pieces in.
In an accident I don't think it'd hold up all that great.

How about welding in some supports?
Running the flat steel across the seat seems like over time it would warp. One of my friends modified his jeep seats in a similar fashion and he needs to take them out and bend them back every once in a while.
Yeah, it's not ideal. I used extremely heavy gauge steel though, so I doubt it will bend. The big bummer is that it's quite heavy. This is a temporary solution until I can get a proper Sparco base/sliders.

A better roll-your-own solution would be using steel square stock. I didn't go that route since I wanted to get maximum height adjustibility, but in retrospect even using 3/4" stock would still give me the range I actually use.
ChinoCharlesOH · Sep 6, 2006#6
Anyone want to take a crack at raising the amount of play in the steering wheel? One of the things I HATE about this car...
Chris07LBNew Jersey · Sep 6, 2006#7
Originally Posted by ChinoCharles
Anyone want to take a crack at raising the amount of play in the steering wheel? One of the things I HATE about this car...
Your thinking is going to make work for me again. Hummmm..
KatanaUnder the hood! · Sep 6, 2006#8
Ιt looks great!
PetersRedYarisThe Black Hills of South Dakota · Feb 9, 2007#9
Originally Posted by ChinoCharles ↑
Anyone want to take a crack at raising the amount of play in the steering wheel? One of the things I HATE about this car...
100% agreed, adjustment is needed!!!
spkrman2 · Feb 9, 2007#10
Originally Posted by PetersRedYaris ↑
100% agreed, adjustment is needed!!!
x500...

i'd like for the wheel to be able to come out farther, oh well.
C2AUTOSPLLoma Linda, CA · Feb 10, 2007#11
Originally Posted by spkrman ↑
x500...

i'd like for the wheel to be able to come out farther, oh well.
Get and aftermarket steering wheel. Hub + QR Spacer + Nardi Sport Rally 350mm will extend the steering wheel atleast 3in.
KatanaUnder the hood! · Feb 13, 2007#12
The european version is fine.
Black YarisToledo, OH · Feb 13, 2007#13
Wonder how hard it would be to get a European Colmn with tilt and telescope?
360cubesOntario · Aug 22, 2007#14
Man. Sparco makes some nice seats. It's a shame my big rear end wouldn't fit in there!
DarkShadowFoxMassachusetts · Aug 14, 2017#16
Originally Posted by Black Yaris ↑
can someone get ahold of these?

http://trdparts.jp/english/parts_seat.html
72101-NP100 & 72102-NP100 Approx. 15mm lowering
404 error

Sent from my LG-H918 using Tapatalk
SirDigbyDenver, Colorado · Aug 14, 2017#17
^^^that was 10 years ago. he's probably dead...