Yarisworld Archive

15x7 30+ offset 205/50 tires will it rub in rear

15 posts · 4,660 views

DeathBeardOriginal postLos Angeles, CA · Feb 10, 2013#1
Sorry to ask such a general question...have an opportunity to get a set of kosei 15x7 30 offset wheels for cheap and swap over my 205/50 tires my car is basically slammed will this rub in the rear?

Replies 14

enviriCT · Feb 10, 2013#2
im sure you'll be fine. many people get +40offset with 10mm penguin spacers without issue. I had an effective +27 offset 16x7 on 195/50/16 tires with tuck and had no issues at all...even with our crooked rear axle beam.
1.5Tampa · Feb 10, 2013#3
That is super subtle not aggressive at all. You should be fine

Any updated pics since you've gone lower?
DeathBeardThread starterLos Angeles, CA · Feb 10, 2013#4
using 150mm megan rear spring chppped rear shock bolt by a good 1.5 inches..The trick to lowering these more was to reuse the oem upper spring seat and lose the spring perches

BEFORE

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Feb 10, 2013#5
After:

Diched the rear spring perches, reused oem upper top hat lowered it by an extra 1inch, once this settles it will be highly tucked, though I am dissapointed with the free travel of the megan yaris shock..I am looking into the Function and Form or D2 offering for the 07 Honda Fit as they are shorter by a good 20mm than the yaris

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Feb 10, 2013#6
Running 2 sets of oem toyota camber bolts in the front (2 camber bolts per wheel) I would conservitively put this at -3..no more fender liner issues..May slot the strut holes if I ever man up and get the TR Motorsport 15x9 36+ offset wheels

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Feb 10, 2013#7
A trip down memory lane....my old ep3 running -5 camber with buddy club coilovers, J'sRacing DC5 tie rod ends, full hfp kit with 03 tailight swap, k20a swap..A top knotch car with top knotch memories

4 attachments not included in this copy

DeathBeardThread starterLos Angeles, CA · Feb 10, 2013#8
I miss my ep3 but the vitz is growing on me just wish you could use camber plates and lose the crap torsion beam

2 attachments not included in this copy

DeathBeardThread starterLos Angeles, CA · Feb 10, 2013#9
RIms for sale $300 pick up
DeathBeardThread starterLos Angeles, CA · Feb 10, 2013#10
Mugen wing, with stock 04 tailights..1 month after I got her on Progress Coilovers, a good coilover sadly no camber plates

1 attachment not included in this copy

DeathBeardThread starterLos Angeles, CA · Feb 10, 2013#11
my old 07 yaris with Type S front lip, on tein basics, not a good coilover imo, these are maxed and still not low and too softly valved/sprung

1 attachment not included in this copy

1.5Tampa · Feb 10, 2013#12
Nice cars lol I still use my 130mm rears springs with the shocks set longer and no issues
TOUGEghostKauai · Feb 10, 2013#13
My car with 15x7+25mm wheels and 205/50/15's:

Picture not included in this copy

No rubbing issues. Could still go a little lower also. I did pull and roll my fenders far enough to clear 225/45/15 tires on the same wheels.
DeathBeardThread starterLos Angeles, CA · Feb 10, 2013#14
Lol I know you run your springs like that 1.5 but I am unsettled about it for some reason..

tougeghost awesome man
GolddeenohColumbia, SC · Feb 13, 2013#15
Am i correct in gathering that 205/50/15s wont be a problem for a car that is lowered 1.8 inches?

and is there a preferred offset range to use?