Yarisworld Archive

crx rebuild

69 posts · 16,211 views · page 2 of 2

Replies continued

ilikericeThread startersavannah, ga · Mar 4, 2013#51
You said it NJ.. Parts will be arriving tomorrow. Will be doing alot of work on it this weekend. Hopefully will be finished being assembled. Then will have to plan a weekend for him to bring the car back to finish putting it in.
KillchainAlbuquerque · Mar 4, 2013#52
First time seeing this thread, I'm always amazed of having the ability,skill and patience for motor rebuilds.👍
ilikericeThread startersavannah, ga · Mar 14, 2013#53
Ok, I did most of this last weekend. I haven't had a chance til now to post these up. Been really busy lately and rarely on the computer. Here is the latest.

THere is a big gap from when I put the head on to putting together the timing belt and stuff. I got carried away and so into the build I forgot to grab the camera to take a picture before the cover went on. Last picture is as it stands now. Gonna do valve adjustment tomorrow and hopefully finish it and have it ready to be dropped in the car.

10 attachments not included in this copy

ilikericeThread startersavannah, ga · Mar 14, 2013#54
Ok, someone was asking how to figure out bearings using the coded numbers and colors.

Ill just do the rod bearings for now. Time is limited for me so this is going to be kinda quick. Sorry, I don't have time to put a slideshow up or video.

Pic 1 and 2: each rod has a number that is cut in half on the side of the rod bearing. by matching up the number you will get a 1-4. In my case I had 2-2-2-3.

Pic 3: on the crank there are letters stamped on the crank once by each in front of each rod journal. as U can see on the picture with the bearings and notebook, I had B-C-B-A.

Pic 5: using the chart here, basically you match up the number with the letter to get a color. So with my first rod bearing (2), I will go over 2 columns and then go down that column til I get to Row (B) and Yellow will be my color for which bearing I will need.

Pic 4: as you can see each bearing has a color on the side of it for easy verification.

Same thing as the crank, except the Letters for the crank are on the block where the rear main seal goes as shown in pic 6.

the numbers are on the crank and you can use the diagram in pic 5 to show you which numbers go for which journal.

Hope this helps a bit for the D16A6 builders

6 attachments not included in this copy

ShroomsterOrlando · Mar 14, 2013#55
if you don't mind my asking, what spring compressor tool is that you're using in seventh pic? is it honda specific or universal?
ilikericeThread startersavannah, ga · Mar 14, 2013#56
Universal. I ordered it online. comes with 3 commonly used adapters, but has cutouts for others so if you wanted a larger or smaller one you can put it there. If I remember I will get a pic of it next time im in the garage
yaris2010RSAngus, Ontario · Mar 14, 2013#57
....that colour code thing is odd....
GolddeenohColumbia, SC · Mar 22, 2013#58
it has been a week any further progress?
junorico24Sydney · Apr 11, 2013#59
How's the build?

Here's is a Yaris cousin Daihatsu Charade.

Picture not included in this copy

It's not done yet.Below is a 1.6 ltr block with a 1.3 ltr head. Will put a 1.3 ltr piston in the 1.6 block.


Picture not included in this copy


It's only a mock up. Gotta send it to the machine shop for cleaning, re-surfacing and port and polish. Yaris is my daily :)
ilikericeThread startersavannah, ga · Apr 11, 2013#60
Cool project. Yea still sitting in my garage. They owner has the transmission and getting it cleaned up. Also he wants to detail his engine bay also. I told him we should hold off until my wedding is finished and done with. Then I can finish his Crx. Been so busy these last 2 weeks. I'll get video and pic when I start her up
DebbyM46227Indianapolis · Apr 11, 2013#61
Originally Posted by NJ Drive ↑
I've had 3 CRX Si, two 1987 and 1988.
They will never make a car like that ever again. Really special!
👍 I had 3 CRX's, bought them all new - never an Si, mine were all the middle (DX?) model, not the HF either. I had a blue & gray '85, a red '87 and my favorite, the red 1988 I kept for 9 years until I sold it to a co-worker's daughter in 1997. She had the rusted rear wheel-well's fixed and she sold it....I still see it being driven around after all these years.

I still miss my CRX, the Yaris doesn't replace it.
ilikericeThread startersavannah, ga · Apr 11, 2013#62
Yea, I remember talking to you about our crx's. such great little cars. I had a red 91 si I wrecked, blue 88 hf, and found a blue 89 dx super cheap then sold the 88. 89 dx ended up getting a integra LS swap, turbo charged, then b18 vtec head, then a CRV B20 with vtec head. Had siR headlights and hood and mugen front bumper, buddy club rear bumper and sideskirts w/door caps. Repainted darker blue and ran my red rims with it..

I would do it again.. except, i wouldn't sell it
justjesusOrange County · May 23, 2013#63
is it running now?
ilikericeThread startersavannah, ga · May 24, 2013#64
Not yet. I was just about to revive this thread. I haven't had a chance to work on it. Mainly because the owner keeps wanting to clean things. He wanted to take the brake booster out and refinish it last weekend and now he wants to replace the evaporator and expansion valve under the dash. I am leaving to go to DC this weekend. I was gonna stay here and finish it up but my wife wants me to go too.. Live in the moment.

This morning I got the motor in the car. all mounted up. I will have pictures when I get back. Next weekend its full blown wide open, gonna get it running before sunday (autocross day)
ilikericeThread startersavannah, ga · Jun 1, 2013#65
Update. I cant find my camera so I have to use my phone camera. Also cant find the damn usb cord to connect to my computer. I will post it up soon enough though.

Cranked up the car today. runs like a champ. Drove it around. now gotta get some miles on it and change the oil again. Pics and video will be posted hopefully later today.
ilikericeThread startersavannah, ga · Jun 2, 2013#66
Incoming pictures and a video.

Footnote: Wife took the video in low quality so she could text it to the owner. I just uploaded it for you guys to see.

Pics are from Friday morning. I got too anxious and already mounted up the motor then realized.. OH damn, forgot to take a pic before. Well, here you go.

I finished it saturday around lunch time and had autocross today. Been test driving it most of saturday.

And the video:

http://www.youtube.com/watch?v=Tg5yN0Wu-r8

2 attachments not included in this copy

racerbLeland, NC · Jun 2, 2013#67
One of my first racecars was an '84 CRX 1.5 then a few years later I bought an '89 Civic Si and an '89 CRX Si, choosing to race the Civic because it actually handled better! Great cars, just feel out of love with Hondas in the early nineties in favor of my first Nissans.

racerb 👏
junorico24Sydney · Jun 3, 2013#68
Wow.. Awesome!!
ilikericeThread startersavannah, ga · Jun 9, 2013#69
Ok, Last post on this. Car is finished and back in the owners hands. Here is a quick video of the last bit of valve adjustment I did and a walk around of the motor while running.
Hope you guys enjoyed this project as much as I did.

http://www.youtube.com/watch?v=T8plh39MsEI