Yarisworld Archive

16 x 6.5 rubbing with 205/50/R16?

13 posts · 8,909 views

PumpkinSteveOriginal postTyne and Wear, UK · Feb 15, 2011#1
Can you tell me sure if these will rub? I have 16" x 6.5" ET45 rims with Tein lowering springs and I want to fit 205 50 R16 tyres, does anyone else have a lowered Yaris and wheels of a similar ET?

Replies 12

Wisher23Bay Area · Feb 15, 2011#2
The tires a little tall, but it should work with no rubbing. I run 205/45/16 with 16x8.5 and 16x8 wheels. Im lowered on tein stechs and get no rub what so ever.
PumpkinSteveThread starterTyne and Wear, UK · Feb 15, 2011#3
According to the online tyre calculator, the 205 50's are the closest match in diameter to my stock wheels, only 5mm smaller overall. I just want to make sure that they definitely don't rub, I think the offset is the thing to watch here, but I'm not sure if ET45 is good or it need to be higher/ lower?
thebarberGrand Rapids, MI · Feb 15, 2011#4
here's mine on 16x6.5 miata wheels, offset is 38iirc and i was on 205-45-16's. lowered about 2" on megan coilovers

Picture not included in this copy
Klink10910 · Feb 16, 2011#5
I am not rubbing at all with 16" Enkei RPF1's offset +43 and 205/50/16 Generals. Lowered via TRD springs and shocks. If I could have gotten the rims at +45 I would have gone that route.
PumpkinSteveThread starterTyne and Wear, UK · Feb 17, 2011#6
So, judging by you guys' posts it's the offset which makes all the difference...

Originally Posted by Thirty-Nine ↑
I rubbed with 205/50/16s (+37) lowered on Megan coilovers.
Where did the wheel rub? The outside arch?
Klink10910 · Feb 17, 2011#7
Yes, offset is the key.
thebarberGrand Rapids, MI · Feb 17, 2011#8
i would only rub on severe dips in the road where the fender plastic would dip and rub the tire

hell, i get that now w/ my rpf1's and 205-50-15's w/ hard driving....
PumpkinSteveThread starterTyne and Wear, UK · Feb 19, 2011#9
I just realised that I have been pretty stupid thinking about these tyres:

the stock tyres are 205 45 R17 which have an overall diameter of 617mm

the 205 50 16 have an overall diameter of 611mm and an equal section width...so how could they NOT fit? they are smaller, if the stock wheels fit then there is no reason why the others wont. The offset difference is only -6mm, surely they will be okay?
bzinn 1University Place,WA · Feb 19, 2011#10
If you have a 45 offset you should be in enough that they only rub on big bumps.

I was running 205/45/17s with a 42 offset and only rubbed on big bumps,when I changed tires I went to a 40 offset and only rub still on the same big bumps on my daily drive....our roads here were built by blind monkeys...pretty bad.

The lower the offset the further out the wheels sit out in the wheelwells and larger the offset the further in they sit.

You should be fine....and it should look great on how it sits....hope that helps.
PumpkinSteveThread starterTyne and Wear, UK · Feb 19, 2011#11
^since the offset is only 6mm different between my stock wheels and my aftermarket wheels, I guess an extreme measure would be to take them to an engineering company and have 6mm milled out of the centre of the wheel, then they would fit perfectly and match the stock rims.

I'm only asking all of this because 205 tyres cost considerably less here than 195, about 20% cheaper I think...
bzinn 1University Place,WA · Feb 19, 2011#12
nahhhh....you should be fine...Im on 42 offset and rarely rub in the front,backs never rub and I havea spacer back there too pushing out 10mm so they are 32 offset.

the rub on the front is where the bumper meets the fender on the liner it wears through in a day or two and you have hardly no rub at all ever then.

You should be fine.
PumpkinSteveThread starterTyne and Wear, UK · Feb 19, 2011#13
🙄 I just realised that because the new rims are 1/2 an inch narrower (6mm on each side) then the +6mm offset is completely negated by that, hence they are in exactly the same position as the stock wheels. So they will definitely not rub...that was hard work 😁

We should compile a proper list of all offset and tyre combinations that people have and whether or not they rub, then others could check for reference when choosing rims and tyres.