For the record, the biggest concern with catalytic converters is the not reducing carbon emissions, but the chemical reactivity of those emissions and their effect on air quality. They really do serve an important purpose, and its not terribly difficult to find a free-flowing cat, either aftermarket, or simply purchasing one intended for a larger engine (a late model V6 cat off a single exhaust vehicle can be found at junkyards pretty cheap.)
For those who want to know, here is a better explanation:
A two-way catalytic converter has two simultaneous tasks:
Oxidation of carbon monoxide to carbon dioxide: 2CO + O2 → 2CO2
Oxidation of unburnt hydrocarbons (unburnt and partially-burnt fuel) to carbon dioxide and water: CxH2x+2 + 2xO2 → xCO2 + 2xH2O (a combustion reaction)
This type of catalytic converter is widely used on diesel engines to reduce hydrocarbon and carbon monoxide emissions. They were also used on spark ignition (gasoline) engines in USA market automobiles through 1981, when the two-way converter's inability to control NOx led to its supersession by three-way converters.
Three-way
Since 1981, three-way catalytic converters have been used in vehicle emission control systems in North America and many other countries on roadgoing vehicles. A three-way catalytic converter has three simultaneous tasks:
Reduction of nitrogen oxides to nitrogen and oxygen: 2NOx → xO2 + N2
Oxidation of carbon monoxide to carbon dioxide: 2CO + O2 → 2CO2
Oxidation of unburnt hydrocarbons (HC) to carbon dioxide and water: CxH2x+2 + 2xO2 → xCO2 + 2xH2O
These three reactions occur most efficiently when the catalytic converter receives exhaust from an engine running slightly above the stoichiometric point. This is between 14.6 and 14.8 parts air to 1 part fuel, by weight, for gasoline. The ratio for LPG, natural gas and ethanol fuels is slightly different, requiring modified fuel system settings when using those fuels. Generally, engines fitted with 3-way catalytic converters are equipped with a computerised closed-loop feedback fuel injection system employing one or more oxygen sensors, though early in the deployment of 3-way converters, carburetors equipped for feedback mixture control were used. While a 3-way catalyst can be used in an open-loop system, NOx reduction efficiency is low. Within a narrow fuel/air ratio band surrounding stoichiometry, conversion of all three pollutants is nearly complete. However, outside of that band, conversion efficiency falls off very rapidly. When there is more oxygen than required, then the system is said to be running lean, and the system is in oxidizing condition. In that case, the converter's two oxidizing reactions (oxidation of CO and hydrocarbons) are favoured, at the expense of the reducing reaction. When there is excessive fuel, then the engine is running rich. The reduction of NOx is favoured, at the expense of CO and HC oxidation.
Oxygen storage
Three-way catalytic converters can store oxygen from the exhaust gas stream, usually when the air fuel ratio goes lean[4]. When insufficient oxygen is available from the exhaust stream the stored oxygen is released and consumed. This happens either when oxygen derived from NOx reduction is unavailable or certain maneuvers such as hard acceleration enrich the mixture beyond the ability of the converter to compensate.
Unwanted reactions
Unwanted reactions can occur in the three-way catalyst, such as the formation of odiferous hydrogen sulfide and ammonia. Formation of each can be limited by modifications to the washcoat and precious metals used. It is difficult to eliminate these byproducts entirely.
For example, when control of hydrogen sulfide emissions is desired, nickel or manganese is added to the washcoat. Both substances act to block the adsorption of sulfur by the washcoat. Hydrogen sulfide is formed when the washcoat has adsorbed sulfur during a low temperature part of the operating cycle, which is then released during the high temperature part of the cycle and the sulfur combines with HC.
Also, a test pipe is a simple and very effective solution for track/racing situations on a car that will be street-driven too. Simply fab-up a pipe to replace your mid-pipe and it only requires a few bolts to be removed and replaced to make the quick switch, kinda like cut-outs back in the day.
For those who want to know, here is a better explanation:
A two-way catalytic converter has two simultaneous tasks:
Oxidation of carbon monoxide to carbon dioxide: 2CO + O2 → 2CO2
Oxidation of unburnt hydrocarbons (unburnt and partially-burnt fuel) to carbon dioxide and water: CxH2x+2 + 2xO2 → xCO2 + 2xH2O (a combustion reaction)
This type of catalytic converter is widely used on diesel engines to reduce hydrocarbon and carbon monoxide emissions. They were also used on spark ignition (gasoline) engines in USA market automobiles through 1981, when the two-way converter's inability to control NOx led to its supersession by three-way converters.
Three-way
Since 1981, three-way catalytic converters have been used in vehicle emission control systems in North America and many other countries on roadgoing vehicles. A three-way catalytic converter has three simultaneous tasks:
Reduction of nitrogen oxides to nitrogen and oxygen: 2NOx → xO2 + N2
Oxidation of carbon monoxide to carbon dioxide: 2CO + O2 → 2CO2
Oxidation of unburnt hydrocarbons (HC) to carbon dioxide and water: CxH2x+2 + 2xO2 → xCO2 + 2xH2O
These three reactions occur most efficiently when the catalytic converter receives exhaust from an engine running slightly above the stoichiometric point. This is between 14.6 and 14.8 parts air to 1 part fuel, by weight, for gasoline. The ratio for LPG, natural gas and ethanol fuels is slightly different, requiring modified fuel system settings when using those fuels. Generally, engines fitted with 3-way catalytic converters are equipped with a computerised closed-loop feedback fuel injection system employing one or more oxygen sensors, though early in the deployment of 3-way converters, carburetors equipped for feedback mixture control were used. While a 3-way catalyst can be used in an open-loop system, NOx reduction efficiency is low. Within a narrow fuel/air ratio band surrounding stoichiometry, conversion of all three pollutants is nearly complete. However, outside of that band, conversion efficiency falls off very rapidly. When there is more oxygen than required, then the system is said to be running lean, and the system is in oxidizing condition. In that case, the converter's two oxidizing reactions (oxidation of CO and hydrocarbons) are favoured, at the expense of the reducing reaction. When there is excessive fuel, then the engine is running rich. The reduction of NOx is favoured, at the expense of CO and HC oxidation.
Oxygen storage
Three-way catalytic converters can store oxygen from the exhaust gas stream, usually when the air fuel ratio goes lean[4]. When insufficient oxygen is available from the exhaust stream the stored oxygen is released and consumed. This happens either when oxygen derived from NOx reduction is unavailable or certain maneuvers such as hard acceleration enrich the mixture beyond the ability of the converter to compensate.
Unwanted reactions
Unwanted reactions can occur in the three-way catalyst, such as the formation of odiferous hydrogen sulfide and ammonia. Formation of each can be limited by modifications to the washcoat and precious metals used. It is difficult to eliminate these byproducts entirely.
For example, when control of hydrogen sulfide emissions is desired, nickel or manganese is added to the washcoat. Both substances act to block the adsorption of sulfur by the washcoat. Hydrogen sulfide is formed when the washcoat has adsorbed sulfur during a low temperature part of the operating cycle, which is then released during the high temperature part of the cycle and the sulfur combines with HC.
Also, a test pipe is a simple and very effective solution for track/racing situations on a car that will be street-driven too. Simply fab-up a pipe to replace your mid-pipe and it only requires a few bolts to be removed and replaced to make the quick switch, kinda like cut-outs back in the day.