I switched to mobil1 5w30 after my 2nd oil change since I had very good results with it with an older car. Runs good. Almost tried amsoil, but heard that it thickens too much as it gets older. Curious about what kind of synthetic m/t oil I should use. I'm not sure if I trust "off brands" like Amsoil and Red Line. Is mobil1 good m/t oil since they make the best motor oil? Whate are your recommendations? (BTW - I hate large predatory corporations like Exxon Mobil, but there is no denying that the best is the best with Mobil 1 synthetic motor oil)
best synthetic oil and m/t oil??
118 posts · 94,407 views · page 1 of 3
Replies 117
Mobil-1 is not bad at all, but neither is Amsoil. Amsoil epitomizes the "little guy" in the Synthetic Oil market. They do not advertise much and are only distributed by dealers. They are the closest thing to a "mom and pop" outfit you will find in sythetic oil. They definately claim to have the "best in synthetics" and I have not heard or read any different. I don't know where you got the "thickening" stuff from. It will suspend more contaminants in the oil, usually after switching from dino to Amsoil, but a good engine flush beforehand will clean that out first, and you oil should look nice and golden amber for quite a while with a good oil filter. Amsoil was the original "synthetic oil" as well. 18 Wheeler Truckers swear by it, because with a bypass oil filter, you can go 100,000 miles+ on an oil change, because the actual oil doesn't break down at all. All this said, I just switched to Mobil-1 5W-30 on Saturday with a Napa Gold filter because I was too lazy to hunt down Amsoil.😁
i am so lucky to have an amsoil dealer 10 minutes away. i hate online ordering, with the shipping fees, wait time AND the possibility of ID theft (you never know!). if this dealer wasn't near me, i'm right there with you guys and running to costco to buy cases of mobil 1. previously used mobil 1 with my '97civic and didnt have any problems. then i got lazy (started working actually!!?!) and just "EZ-Lubed" my baby. that was the biggest mistake ever. lower mpg. engine not as smooth. we recently just put her back on synthetics (amsoil), and just changed to amsoil after 1K miles on our new van. cant wait to see how the oil looks after the next oil change!
--B
ps: the prices are very comparable too, so just get whatever is convenient for you. anything's better than dino...
--B
ps: the prices are very comparable too, so just get whatever is convenient for you. anything's better than dino...
its not always good to switch to synthetic oil so soon, things like valve guides and seals need to be bathed in it for at least 20,000 Km to absorb oil to offer superior lubrication and seal funtionality
just don't switch back now that you are running it.
just don't switch back now that you are running it.
Amsoil, or redline are the best of the best.
Both are pure 100% group IV or V, poa or Ester based lubricants.
By FAR more stable over the oils lifetime then any other conventional or group III oil.
Both are pure 100% group IV or V, poa or Ester based lubricants.
By FAR more stable over the oils lifetime then any other conventional or group III oil.
sounds like amsoil is good stuff. i know redline is good because my dad and i have been running it in our motorcycles for years.
Well, I am very tempted to switch to Amsoil or Mobil 1, too, on my older (1994, 170k) 4runner, but, Guys, can anybody explain, pls, what the difference is between 5W-30 and 10W-30... it's getting very confusing, when you go to those websites "find the oil that best fits your car", you answer the questions what type of vehicle you own, the year and so on, and, finally, you get the answer like 5W-30 or 10W-30... I guess the question is how do you know for sure what do you need: 5W or 10W....
We used Penzoil for years and it seems like the car runs good, but I wish I could do something good for my old and lovable Toyota 4runner.... any input would be very appriciated
Final thought: when a car has 170k miles on it, is it really worth changing to synthetic oil?
We used Penzoil for years and it seems like the car runs good, but I wish I could do something good for my old and lovable Toyota 4runner.... any input would be very appriciated
Final thought: when a car has 170k miles on it, is it really worth changing to synthetic oil?
Well first off Amsoil and Mobil1 are two completely different types of oils/lubricants.
Mobil 1 is just highly refined crude oil/mineral oil and a basic group III type oil.
Amsoil and Redline are both completely man made lubricants and contain no pertrolium/mineral oil Group IV-V oils
As for the difference between the 5w-30 and 10w-30
The 5w mean it has a lower cold pour point. The lower the W weight the better the oil will flow when cold.
Both a 5w-30 and 10w-30 are still a 30 weight oil or SAE 30 when hot but the lower W weight means it will flow better at colder temps.
For example
Mobil1 10w-30 has a pour point of -45 oC
Mobil1 5w-30 has a pourpoint of -54 oC
Amsoil 10w-30 5w-30 and 0w-30 have a pour point of - 50 ~ -54 oC
As for what one to use in your car... check the owners manual it will say in there.
All Yaris engine are designed to use a 5W-30 engine oil however if you live in a hot climate you can still safely run a 10w-30.
With new engines today the tolerances are much tighter then you fathers V8 from the 70's and a lighter oil is needed and the lower the pour point the better. It allows oil to flow easily through the engine to reach vital engine components quicker to help reduce start up damage.
FWIW I use Amsoil 2000 0w-30 oil in my Yaris and have used it in my truck as well as my laser with awesome results.
I build and rebuild regular and race engines for a living and have used every kind of oil out there. Amsoil and Redline lubricants are the best of the best.
Royal purple is a good runner up but they do suffer from some quality control issues.
As far as group III oils go Mobil 1 is one of the best along with Motul and many others. oils like Qstate synthetic, Castrol Syntec, Lucas are the amoung the lowest quality group III oils. But even these oils are far better then any conventional oil or synthetic blend (group I and II oils)
You can switch to synthetics anytime
What it will do is provide more HP from less friction and cooler engine temps and better mileage.
On the down side if you switch you should do an engine flush. Synthetic will clean your engine as you drive so if you have sludge build up it is possible in high mileage cars for oil leaks to develop as the sludge deposits that were blocking oil leaks are cleaned away.
If at any time you want to switch back you can with no problems.
Mobil 1 is just highly refined crude oil/mineral oil and a basic group III type oil.
Amsoil and Redline are both completely man made lubricants and contain no pertrolium/mineral oil Group IV-V oils
As for the difference between the 5w-30 and 10w-30
The 5w mean it has a lower cold pour point. The lower the W weight the better the oil will flow when cold.
Both a 5w-30 and 10w-30 are still a 30 weight oil or SAE 30 when hot but the lower W weight means it will flow better at colder temps.
For example
Mobil1 10w-30 has a pour point of -45 oC
Mobil1 5w-30 has a pourpoint of -54 oC
Amsoil 10w-30 5w-30 and 0w-30 have a pour point of - 50 ~ -54 oC
As for what one to use in your car... check the owners manual it will say in there.
All Yaris engine are designed to use a 5W-30 engine oil however if you live in a hot climate you can still safely run a 10w-30.
With new engines today the tolerances are much tighter then you fathers V8 from the 70's and a lighter oil is needed and the lower the pour point the better. It allows oil to flow easily through the engine to reach vital engine components quicker to help reduce start up damage.
FWIW I use Amsoil 2000 0w-30 oil in my Yaris and have used it in my truck as well as my laser with awesome results.
I build and rebuild regular and race engines for a living and have used every kind of oil out there. Amsoil and Redline lubricants are the best of the best.
Royal purple is a good runner up but they do suffer from some quality control issues.
As far as group III oils go Mobil 1 is one of the best along with Motul and many others. oils like Qstate synthetic, Castrol Syntec, Lucas are the amoung the lowest quality group III oils. But even these oils are far better then any conventional oil or synthetic blend (group I and II oils)
You can switch to synthetics anytime
What it will do is provide more HP from less friction and cooler engine temps and better mileage.
On the down side if you switch you should do an engine flush. Synthetic will clean your engine as you drive so if you have sludge build up it is possible in high mileage cars for oil leaks to develop as the sludge deposits that were blocking oil leaks are cleaned away.
If at any time you want to switch back you can with no problems.
Thanks for a wonderful input. Now it makes things more clear.... I made some calculations here and.... well, the oil change with Amsoil synthetic oil somehow hits your pocket.... For my Toyota 4runner, that is, V6 3.0 engine, I may need 1.5 gallons of oil, right? The price for 1 gallon (according to the Amsoil web-site) is $27.15, so it winds up to $41.00, then +$17.00 Amsoil oil filter and the service price (approximately $30.00) for the oil change and then oil shipping if you order it on-line.... it comes to over $100.00 for the whole procedure.... right? Well, I have to think about it, I guess....🙄
find a local amsoil dealer, change it yourself, and do it once a year!! if you cant do it yourself, then a decent mom and pops shop shouldnt charge more than 20 bucks for the service if you supply all of the goods. it actually comes out cheaper than regular mobil 1 synthetic oil (needs more frequent changes), and is very comparable in price to mobil 1 extended service oil. it really does suck if you dont have a local dealer to work with.Originally Posted by zyovkaThanks for a wonderful input. Now it makes things more clear.... I made some calculations here and.... well, the oil change with Amsoil synthetic oil somehow hits your pocket.... For my Toyota 4runner, that is, V6 3.0 engine, I may need 1.5 gallons of oil, right? The price for 1 gallon (according to the Amsoil web-site) is $27.15, so it winds up to $41.00, then +$17.00 Amsoil oil filter and the service price (approximately $30.00) for the oil change and then oil shipping if you order it on-line.... it comes to over $100.00 for the whole procedure.... right? Well, I have to think about it, I guess....🙄
--B
ps: i did a amsoil flush with my initial change, just becuase i didnt want any dino residue "dirtying" up my fresh synthetic oil...ahhhhh
Originally Posted by zyovkaThanks for a wonderful input. Now it makes things more clear.... I made some calculations here and.... well, the oil change with Amsoil synthetic oil somehow hits your pocket.... For my Toyota 4runner, that is, V6 3.0 engine, I may need 1.5 gallons of oil, right? The price for 1 gallon (according to the Amsoil web-site) is $27.15, so it winds up to $41.00, then +$17.00 Amsoil oil filter and the service price (approximately $30.00) for the oil change and then oil shipping if you order it on-line.... it comes to over $100.00 for the whole procedure.... right? Well, I have to think about it, I guess....🙄
Yeah but that's good for 35,000 miles or once a year
How many regular oil changes will you have to do running mobil 1 over 35,000 miles or once a year?
Amsoil is usually A LOT cheaper in the long run.
I change my oil every 6 months and it still saves me a lot of $$$
An amsoil dealer can get you better discounts by signing you up as a prefered customer.
If you want PM or email me and I'll give you the contact infor for my Amsoil distributer
thanks, but.... the oil change still includes other services such as lubrication, changing the air filter, rotating the tires etc.... which has to be done every 3.000 or so miles regardless of the oil change and those services are approx. $30.00 without oil change, correct me if I'm wrong..... pls
switching to synthetic oil on a new car is the g-hey.
wait four years, have a 100,000 Kms on it then make the switch unless you want to install new valve guides and seals.
you will be buring oil in no time if you switch.
wait four years, have a 100,000 Kms on it then make the switch unless you want to install new valve guides and seals.
you will be buring oil in no time if you switch.
Originally Posted by firefly1_0switching to synthetic oil on a new car is the g-hey.
wait four years, have a 100,000 Kms on it then make the switch unless you want to install new valve guides and seals.
you will be buring oil in no time if you switch.
Who ever told you that is a complete jackass
I've never had one of my race engines smoke unless there was a major engine problem.
I've never had any oil related problems since switching to synthetic back in the early 90's.
I've been building and rebuilding engine since I worked at Yamaha over 15 years ago. Everything from bikes to cars to outboards and ATV 2 strokes and 4 strokes.
True an engine should be run in using a regular oil and run in hard to properly seat rings, but valve guides and valve seals do not need to be broken in. They are machined and cast to exact clearance specs and preserving these specs the best you can will prevent any wear or oil leaking.
I highly doubt the dealership will rotate your tires every 3000 miles and no air filter needs to be changed that often. Tires should be rotated every 6 months. The cabin air filter should be changed a little more often but even that is an extra cost at the dealership and not part of any required warranty issue.Originally Posted by zyovkathanks, but.... the oil change still includes other services such as lubrication, changing the air filter, rotating the tires etc.... which has to be done every 3.000 or so miles regardless of the oil change and those services are approx. $30.00 without oil change, correct me if I'm wrong..... pls
I don't think this car has grease zerks on the suspension/steering components so basically they just change the oil and check the other fluid levels.
If you have a torque wrench you can rotate the tires in 30 minutes yourself at home. All you need is a jack stand and 1/2 torque wrench (less then $15 at harbour freight) Jack up the rear and put a jack stand under it just up the front on the same side. Put the rear tire on the front and front on the rear. Do not put right tires on the left side or left on the right. Once a tire has been used it's best to keep the tires rotation the same, changing sides will change the tires rotation and that causes them to bulge out and belts to break etc. Use a torque wrench to evenly torque the lug nuts to the proper specs. Quick and simple.
NO dealership can void any warranty if you decide to do your own maintenance. Not even on a lease, Just be sure to keep records of What work was done, and when and akeep receipts for any products you buy like oil, air filters, spark plugs, etc etc.
Check with your local dealership. I know my local dealership uses Mobil 1 on request. It's not the best oil out there but it is better then using a conventional oil. At least this way you get the dealer care and synthetic oil.
Originally Posted by 07WYarisRSWho ever told you that is a complete jackass
I've never had one of my race engines smoke unless there was a major engine problem.
I've never had any oil related problems since switching to synthetic back in the early 90's.
I've been building and rebuilding engine since I worked at Yamaha over 15 years ago. Everything from bikes to cars to outboards and ATV 2 strokes and 4 strokes.
True an engine should be run in using a regular oil and run in hard to properly seat rings, but valve guides and valve seals do not need to be broken in. They are machined and cast to exact clearance specs and preserving these specs the best you can will prevent any wear or oil leaking.
if its designed to run with synthetic oil from the start then it works... AMG does it.
proper engine break in is at least 20,000 KM, no if's, and's or butt's.
the benifits that synthetic can provide are better cold winter starts, and better protection with an older engine.
we already get 5,000 miles between changes using regular oil in these cars, is that not enough?
if you are really that keen on running synthetic, i would check your warranty,and talk to a toyota mechanic, i can't be bothered to look, i talked the dealer into 5 years of free oil changes when i bought mine...
😆 😆 😆 😆
Firefly, you are joking... right... I mean if not, you don't know the first thing about what a "synthetic" oil is. 😲 A synthetic oil is basically an oil with molecules of a specific size and shape. They also have a low burn off rate, so the oil stays oil and doesn't turn to sludge from heat.
I hope you are just pulling our leg here, but if not, please do some research on the subject. Toyota mechanics are not the people to talk to about oil, they want you to use Toyota OEM oil and filters only. duh...
My friend heard the EXACT same song and dance from the Acura dealership. He fell for it hook-line-and sinker, like someone else I know on this Yaris board.😁
"Designed to run with synthetic" That's a good one.👍 It should be "requires oil that wont thicken up like dino in 1000 miles."
Firefly, you are joking... right... I mean if not, you don't know the first thing about what a "synthetic" oil is. 😲 A synthetic oil is basically an oil with molecules of a specific size and shape. They also have a low burn off rate, so the oil stays oil and doesn't turn to sludge from heat.
I hope you are just pulling our leg here, but if not, please do some research on the subject. Toyota mechanics are not the people to talk to about oil, they want you to use Toyota OEM oil and filters only. duh...
My friend heard the EXACT same song and dance from the Acura dealership. He fell for it hook-line-and sinker, like someone else I know on this Yaris board.😁
"Designed to run with synthetic" That's a good one.👍 It should be "requires oil that wont thicken up like dino in 1000 miles."
ok then, if thats what you guys think then fine, the fact that syn oil offers double the heat capcity is a given, it says so right on the lable...
think of what kind of car you are driving, its not a high performance car, force fed, running nitrous oxide or fueled by LPG or LNG, the things that generate higher heat in the combustion chamber and high exhaust and head temps.
unless you're running with half the recomended amount of coolant you will never see this type of engine condition happen.
hell, its your money... do what ever you want.
think of what kind of car you are driving, its not a high performance car, force fed, running nitrous oxide or fueled by LPG or LNG, the things that generate higher heat in the combustion chamber and high exhaust and head temps.
unless you're running with half the recomended amount of coolant you will never see this type of engine condition happen.
hell, its your money... do what ever you want.
What is break in?Originally Posted by firefly1_0if its designed to run with synthetic oil from the start then it works... AMG does it.
proper engine break in is at least 20,000 KM, no if's, and's or butt's.
the benifits that synthetic can provide are better cold winter starts, and better protection with an older engine.
we already get 5,000 miles between changes using regular oil in these cars, is that not enough?
if you are really that keen on running synthetic, i would check your warranty,and talk to a toyota mechanic, i can't be bothered to look, i talked the dealer into 5 years of free oil changes when i bought mine...
What does it do?
What is the difference between and engine designed to use synthetic and one that is not?
What synthetics do not meet mfg oil standards?
When you are breaking in an engine you are seating the rings. As the rings seat engine compression levels rise until the rings are fully seated.
improper break in, like driving your car like a pansy will not product high enough combustion pressure to force the rings out to properly seat. Proper break in is very important and 90% of it is done within the first 40 minutes of running the engine. The main things to avoid are steady cruise speeds, idleing, overrevving, or short trips under 5 minutes. After a tank of fuel the rings are pretty much seated as much as they will (depending on how it was run)
Everything else like bearings and valve guides are precision machined to exact specs. Again these are not engines from the 70's
Running in an engine does not in anyway shape or form take 20,000km
For phuck sakes man some people don't put 20,000km on their car in a year...
My sister in laws Cobalt is 2 years old and does not have 20,000km.
The difference between oil is this
Group I = Conventional oil is group I oil (basic refined mineral oil)
Group II = Synthetic blend is a group II oil and is a mixture of synthetic base Group III = highly refined crude oil but is classed as full synthetic and usually contain low to moderate levels of POA's and Esters (Mobil 1, syntec, Motul )
Group IV lubricants are pure synthetics POA based and contain no mineral oil (Amsoil Royal purple)
Group V lubricants are polyolEster based and also contain no mineral oil (Amsoil and Redline)
Any one of these oils can be used in ANY automotive engine, most if not all meet or by far exceed mgf oil requirements.
Some engines like in Cadillac, lincoln, BMW, Corvette, lexus, etc come with synthetic in them NEW off the showroom floor.
Why do Toyota dealers offer Mobil 1 for oil changes?
Please befor you make yourself look real stupid just stop talking about what you don't know anything about !
The fact is engine wear out, and using a better lubricant will greatly extend the life and performance of the engine. instead of an engine running 300,00km and burning oil, large loss of compression and overall loss of performance with TRUE synthetic you can greatly reduce the ring and cylinder wear, friction, heat and because there are no by products to oxidize and turn to sludge performance and oil flow is not lost doe to engine deposits.
With my race engine using EGT/CHT ive seem as much as 30degree drop in egt's just by switching to Amsoil. I went from rebuilding our drag and race engines every few races to once a season or longer.
FWIW I built a turbo sprint a few years back.Originally Posted by firefly1_0ok then, if thats what you guys think then fine, the fact that syn oil offers double the heat capcity is a given, it says so right on the lable...
think of what kind of car you are driving, its not a high performance car, force fed, running nitrous oxide or fueled by LPG or LNG, the things that generate higher heat in the combustion chamber and high exhaust and head temps.
unless you're running with half the recomended amount of coolant you will never see this type of engine condition happen.
hell, its your money... do what ever you want.
It was an automatic, carbed non turbo and we made it an EFI, turbo 5 speed.
1L 3cyl TI
Blasted and decked block
.020" off the head and new valves (OEM cam for now)
Fully ported and polished head, intake, turbo, mani.
Full SS 2.25” mandrel bent exhaust No muffler and high flow cat
Balanced rods/OEM pistons, polished rods and minor crank touch up.
Oversized radiator
High flow injectors
Fuel regulator
inline 45psi fuel pump
Anti lag controller
K&N filter and cold air intake
boost controler
Stock turbo @ stock 15 and 22psi
Ractive gauges (boost, oil, water temp, A/F meter)
4th injector injector wired up at 15-16psi
Accel high power ignition, coil, wires
NGK plugs (indexed)
I/C ram air
ACT 2600 clutch
Guess what... it runs on Synthetics
and thats what i have as my race car and its pushing about 115 HP, i will add about 30-40 more with fuel management this winter.Originally Posted by 07WYarisRSFWIW I built a turbo sprint a few years back.
It was an automatic, carbed non turbo and we made it an EFI, turbo 5 speed.
1L 3cyl TI
Blasted and decked block
.020" off the head and new valves (OEM cam for now)
Fully ported and polished head, intake, turbo, mani.
Full SS 2.25” mandrel bent exhaust No muffler and high flow cat
Balanced rods/OEM pistons, polished rods and minor crank touch up.
Oversized radiator
High flow injectors
Fuel regulator
inline 45psi fuel pump
Anti lag controller
K&N filter and cold air intake
boost controler
Stock turbo @ stock 15 and 22psi
Ractive gauges (boost, oil, water temp, A/F meter)
4th injector injector wired up at 15-16psi
Accel high power ignition, coil, wires
NGK plugs (indexed)
I/C ram air
ACT 2600 clutch
Guess what... it runs on Synthetics
one step further with the build though, bored to 75mm with a CR that is about 8.2:1 on 10 psi from a chrysler le barron turbo run through a FMIC.
and guess what it runs on 15w40 regular plain jane oil.
no matter what you run, you have think what you are running from. sludge? ok then run a high detergent oil and change your filter half way between oil changes...
😆 The sludge I'm afraid of comes from Dino oil itself breaking down quickly, from normal engine heat. I have seen the results of Pennzoil and Quacker State. Dirty crusty heads, an overall amber film over the lifters and cam. This comes from dino baking onto surfaces, and turning black and waxy in the corners of your valve covers. No Way Jose', not for me. I have been using synthetics for about 15 years now, and it's funny how I've never had a single engine malfunction from any hardware lubricated with synthetic oil. And when looking in the oil filler hole, it is shiny like new. But I have friends, oh yes, that don't believe in synthetics. Their engines are quite dirty and run like crap. If everyone used synthetics, mechanics would not be quite so rich! hehe You are in Alberta, and you don't use synthetics? What about when dino thickens up in the cold, and the first second of cranking you get metal on metal and OUCH! That hurts!
Think of thickened oil being filtered. The filter gets its pores clogged quicker with waxy crap and hello bypass valve, and dirty oil coating your engine. Real Nice!
You are like an old school mechanic... "I don't wants no FAKE OIL! I wants REAL OIL!"🤣
Think of thickened oil being filtered. The filter gets its pores clogged quicker with waxy crap and hello bypass valve, and dirty oil coating your engine. Real Nice!
You are like an old school mechanic... "I don't wants no FAKE OIL! I wants REAL OIL!"🤣
That again is where you are wrong firefly.
Sludge is not a problem with an oil that contains no mineral oil. There are no mineral oil by products to break down. you can literally run thousands of miles and have no sludge, carbon or by product depostis in your engine.
That's why companies like Amsoil and Redline recommend and oil flush before switching to their oils after running conventional oil. Because introducting a ester or poa based synthetic will clean away sludge and can clog up the oil filter prematurely and then you basically running on unfiltered oil.
Using an engine flush will remove most of the sludge and deposits first then you have no problems with filters plugging up prematurely.
I'm still amazed after 10+ years of using synthetic at some of the engine I have pulled apart that were running synthetic. Heck I even posted pics on here a while ago comparing conventional and Amsoil on well used engines.
What you are eliminating is friction and heat and lots of it. In a turbo charged car you need the best oil you can get.
Try 400,000km on a stock turbo running 20psi... that's what my sunbirt GT runs. Compression is still within' 5psi of stock, does not use ANY oil between oil changes. With less heat and friction you gain more HP and better mileage.
A dyno will not lie, test your car before and after.
test your car then swap the engine oil with Amsoil 2000 20w-50 racing oil
Amsoil 75w-90 in the trans and re-test it.
You will not only see lower EGT, oil temps but higher HP numbers.
OR do some independent lab testing
send in a sample of your conventional oil after 500miles and a sample of Amsoil after 5000 miles and see what one comes out on top.
Sure it's easy to say I have never had a problem running this or that oil but group IV and V lubricants are FAR better then any conventional oil. Aircraft and tractor trialers often run these because the oils last 500,000km or more with bypass filtering set ups. NO conventional oil will withstand that kind of punishment.
On royal purples web site you can view the before and after videos of cars tested on the dyno from shows like Hot rod TV and horsepower TV etc.
If you think a conventional oil is good, MAN a true synthetic like redline or Amsoil will amaze you.
don't talk to the dealers that will try to push house brand oils or have you come in for service
Better yet walk around the pits of you local race tracks both street and off road bike and ATVs and see what the professional engine builders and racers are using.
They use them because they are the best
When I worked and Raced for both Yamaha and Arctic cat we had several oil sponsers but used Amsoil because it was what allowed us to run year after year with no DNF's and save us thousands of dollars every month because there was no need to rebuild the engines.
As i said before I'm a motorcycle /ATV mechainc, that's what I do. even though I do sell Amsoil I do use it in my shop. for the people that want a cheaper oil I use mobil 1 or shell.
Synthetic have save me and my customer thousands of $$$ over the years in repair costs. A DNF can make or break a championship and I have never had anengine failure since running synthetic. I've almosy eliminated any gearbox wear, extend clutch like 3X and engine wear has also be greatly reduced.
Sludge is not a problem with an oil that contains no mineral oil. There are no mineral oil by products to break down. you can literally run thousands of miles and have no sludge, carbon or by product depostis in your engine.
That's why companies like Amsoil and Redline recommend and oil flush before switching to their oils after running conventional oil. Because introducting a ester or poa based synthetic will clean away sludge and can clog up the oil filter prematurely and then you basically running on unfiltered oil.
Using an engine flush will remove most of the sludge and deposits first then you have no problems with filters plugging up prematurely.
I'm still amazed after 10+ years of using synthetic at some of the engine I have pulled apart that were running synthetic. Heck I even posted pics on here a while ago comparing conventional and Amsoil on well used engines.
What you are eliminating is friction and heat and lots of it. In a turbo charged car you need the best oil you can get.
Try 400,000km on a stock turbo running 20psi... that's what my sunbirt GT runs. Compression is still within' 5psi of stock, does not use ANY oil between oil changes. With less heat and friction you gain more HP and better mileage.
A dyno will not lie, test your car before and after.
test your car then swap the engine oil with Amsoil 2000 20w-50 racing oil
Amsoil 75w-90 in the trans and re-test it.
You will not only see lower EGT, oil temps but higher HP numbers.
OR do some independent lab testing
send in a sample of your conventional oil after 500miles and a sample of Amsoil after 5000 miles and see what one comes out on top.
Sure it's easy to say I have never had a problem running this or that oil but group IV and V lubricants are FAR better then any conventional oil. Aircraft and tractor trialers often run these because the oils last 500,000km or more with bypass filtering set ups. NO conventional oil will withstand that kind of punishment.
On royal purples web site you can view the before and after videos of cars tested on the dyno from shows like Hot rod TV and horsepower TV etc.
If you think a conventional oil is good, MAN a true synthetic like redline or Amsoil will amaze you.
don't talk to the dealers that will try to push house brand oils or have you come in for service
Better yet walk around the pits of you local race tracks both street and off road bike and ATVs and see what the professional engine builders and racers are using.
They use them because they are the best
When I worked and Raced for both Yamaha and Arctic cat we had several oil sponsers but used Amsoil because it was what allowed us to run year after year with no DNF's and save us thousands of dollars every month because there was no need to rebuild the engines.
As i said before I'm a motorcycle /ATV mechainc, that's what I do. even though I do sell Amsoil I do use it in my shop. for the people that want a cheaper oil I use mobil 1 or shell.
Synthetic have save me and my customer thousands of $$$ over the years in repair costs. A DNF can make or break a championship and I have never had anengine failure since running synthetic. I've almosy eliminated any gearbox wear, extend clutch like 3X and engine wear has also be greatly reduced.
can you please look back at any of my posts in this thread and see if at any time i said, synthetic oil is bad?
never did i say that, all i said was that its not the greatest for a NEW car. sure once you have it broken in, do what you like.
i have used and still use syn oil in other projects. just not on a brand new car that is on its 2nd or 3rd oil change.
that is all i ever really said. but you guys seem to think that i was attacking the use of it all together.
never did i say that, all i said was that its not the greatest for a NEW car. sure once you have it broken in, do what you like.
i have used and still use syn oil in other projects. just not on a brand new car that is on its 2nd or 3rd oil change.
that is all i ever really said. but you guys seem to think that i was attacking the use of it all together.
pretty much if ...
"using it in a new car is ghey !"
you claim it will somehow damage the valve guides and seals
you have to wait 4 years or 100,000km
takes 20,000 to break in an engine.
I agree and will always stand by the fact that an engine/any engine should be run in using a group I to group III oil. NOT a group IV or V lubricant.
But once the engine is run in (compression level has reached it peak) and the sooner you switch to a snythetic the sooner you start to protect the engine and start reducing friction and heat. Anytime after the first oil change is perfect.
It will NEVER take 20,000km for compression to reach it's peak. Infact most most can be run in in less then an hour.
I just waited the until my first oil change to swap in the synthetic.
What kind of oil do you use because the dollar stores sells the ecaxt same oil you buy from canadian tire for $1 liter.
sometimes 2 for a $1
"using it in a new car is ghey !"
you claim it will somehow damage the valve guides and seals
you have to wait 4 years or 100,000km
takes 20,000 to break in an engine.
I agree and will always stand by the fact that an engine/any engine should be run in using a group I to group III oil. NOT a group IV or V lubricant.
But once the engine is run in (compression level has reached it peak) and the sooner you switch to a snythetic the sooner you start to protect the engine and start reducing friction and heat. Anytime after the first oil change is perfect.
It will NEVER take 20,000km for compression to reach it's peak. Infact most most can be run in in less then an hour.
I just waited the until my first oil change to swap in the synthetic.
What kind of oil do you use because the dollar stores sells the ecaxt same oil you buy from canadian tire for $1 liter.
sometimes 2 for a $1
i'm getting free oil changes for the next 4 years from the dealer only because i asked for them when i bought the car and they agreed.
i buy the car, they work on it, it breaks, they fix it and i am happy.
if we agree to disagree on this then it will be over and we can go about our day.
you like sooner i like the longer wait. that is all.
i buy the car, they work on it, it breaks, they fix it and i am happy.
if we agree to disagree on this then it will be over and we can go about our day.
you like sooner i like the longer wait. that is all.
Hi all,
Wow, this really is a hot topic.
I've switched to fully synthetic Castrol Edge Sport 5w-30 after 2400km's along with a puralator pure one filter. I believe that engine's should be run in with dino oil. The engine should be run in correctly, varying rpm's and loads, moving up to higher rpms and loads as kilometers build. Many have said modern engines run in in approximately the first 500kms( piston rings, seals, cylinder walls... the important stuff). So I thought I'd make sure by letting it run in for 2400kms. The valve train (cams, guides etc) won't run in in this time, but tolerances are so good these days that it's not necessary I believe.
One thing I noticed was that fuel efficiency has increased noticeably using synthetic. So that means friction has been reduced and efficiency increased. If I get glazed bores, smoking, blow by etc... you's will be the first to know about it.
Thanks all:)
Wow, this really is a hot topic.
I've switched to fully synthetic Castrol Edge Sport 5w-30 after 2400km's along with a puralator pure one filter. I believe that engine's should be run in with dino oil. The engine should be run in correctly, varying rpm's and loads, moving up to higher rpms and loads as kilometers build. Many have said modern engines run in in approximately the first 500kms( piston rings, seals, cylinder walls... the important stuff). So I thought I'd make sure by letting it run in for 2400kms. The valve train (cams, guides etc) won't run in in this time, but tolerances are so good these days that it's not necessary I believe.
One thing I noticed was that fuel efficiency has increased noticeably using synthetic. So that means friction has been reduced and efficiency increased. If I get glazed bores, smoking, blow by etc... you's will be the first to know about it.
Thanks all:)
I've been using mobil 1 on all my vehicle for 12 years. Its all they've known. And as my mechanic has said my engines are like brand new inside.
I switched to amsoil with my yaris after reading that it is a step up from mobil 1. I did run the yaris for the first 3000 miles on whatever toyota put in it to begin with.
I switched to amsoil with my yaris after reading that it is a step up from mobil 1. I did run the yaris for the first 3000 miles on whatever toyota put in it to begin with.
Well, Guys, as far as our Yaris has only 180 miles on the odometer, I'll wait with Amsoil for a while, but already have found the local dealer, here, in Milwaukee, so my other car, 4runner, is definitely getting engine flush and Amsoil with a next oil change... thanks a lot for a very valuable inputs and hot discussion👏
recently found bonus of changing to amsoil: my engine is running MUCH smoother and efficiently. case in point, i used to travel at 65mph @ 2000rpm. i now travel @ 71mph @ 2000rpm. you either take it as a bump in power (more speed at same rev) or a bump in fuel efficiency (less rev needed for same speed). either way, i am ridiculously happy. i'll update the fuel efficiency after a few fill-ups.
--B
ps: this is for my sienna. i LOVE that V6...
--B
ps: this is for my sienna. i LOVE that V6...
Besides the power you gain and fuel you save you can save a LOT of $$$ using amsoil.
With Amsoil 2000 0w-30 and Amsoil filter it's good for 35,000 miles or one year
figure that out compared to how many regular oil changes you will do at 500mile intervals plus filters etc
you save $$$ using Amsoil in most cases unless you are running the cheapest conventional oils out there.
lets use my truck (99 chevy Xtreme) as an example.
Before I sold it, I put 100,000km on it in three years
5L of Amsoil X $9.70 plus filter at 16.45 =$65
Mobil 1 at $ 6 and purolator filter at $5 = $35
good regular conventional oil at $3 and filter $5 $ 20
Mobil 1 and conventional oil recommend 5000km oil changes that 20 oil changes over 3 years
Amsoil recommends I year oil changes or every 35,000 miles (what ever comes first)
Amsoil ($65 x 3) = $195
Mobil1 ($ 35 x 20) = $700
Regular conventional oil ($20 X20) = $400
Even if you are like me and change your Amsoil every 6 months that still only $390.
It's still cheaper then using mobil1 or most conventional oils and a group IV or V synthetic will protect your engine and free up more HP MUCH better then any conventional or even group III oil.
Now just think how much money I have saved in my laser with 300,000km on the odometer. 7 oil changes.
And after 300,000km the compression is still perfect, does not use more then a liter of oil between changes, no dreaded DSM lifter tic, and no dreaded auto trans O/D clutch slip. That would have been 60 oil changes using regular oil or Mobil 1. That's $455 with Amsoil vs $2100 with Mobil 1
I don't know about you guys but I would rather save my $$$ then give it to big huge oil companies that rip us off fuel fuel prices as well.
With Amsoil 2000 0w-30 and Amsoil filter it's good for 35,000 miles or one year
figure that out compared to how many regular oil changes you will do at 500mile intervals plus filters etc
you save $$$ using Amsoil in most cases unless you are running the cheapest conventional oils out there.
lets use my truck (99 chevy Xtreme) as an example.
Before I sold it, I put 100,000km on it in three years
5L of Amsoil X $9.70 plus filter at 16.45 =$65
Mobil 1 at $ 6 and purolator filter at $5 = $35
good regular conventional oil at $3 and filter $5 $ 20
Mobil 1 and conventional oil recommend 5000km oil changes that 20 oil changes over 3 years
Amsoil recommends I year oil changes or every 35,000 miles (what ever comes first)
Amsoil ($65 x 3) = $195
Mobil1 ($ 35 x 20) = $700
Regular conventional oil ($20 X20) = $400
Even if you are like me and change your Amsoil every 6 months that still only $390.
It's still cheaper then using mobil1 or most conventional oils and a group IV or V synthetic will protect your engine and free up more HP MUCH better then any conventional or even group III oil.
Now just think how much money I have saved in my laser with 300,000km on the odometer. 7 oil changes.
And after 300,000km the compression is still perfect, does not use more then a liter of oil between changes, no dreaded DSM lifter tic, and no dreaded auto trans O/D clutch slip. That would have been 60 oil changes using regular oil or Mobil 1. That's $455 with Amsoil vs $2100 with Mobil 1
I don't know about you guys but I would rather save my $$$ then give it to big huge oil companies that rip us off fuel fuel prices as well.
If you are happy I quess that's all that matters.Originally Posted by firefly1_0i'm getting free oil changes for the next 4 years from the dealer only because i asked for them when i bought the car and they agreed.
i buy the car, they work on it, it breaks, they fix it and i am happy.
if we agree to disagree on this then it will be over and we can go about our day.
you like sooner i like the longer wait. that is all.
Most car dealers in Canada buy oil in bulk below wholesale from Shell or Esso and
it cost the dealers next to nothing. Less then a dollar a liter for 55 gallons (210 liters) and they usually charge $20 a gallon or more for it.
With that kind of money rolling in the door they don't care about free oil changes to some customers, or doing some promotions They will recommned the cheap stuff to customers because that's where they make the big money.
Some do supply more costly synthetics.
My local GM and toyota dealers gives the first couple changes for free and every 5th oil change free after that. Both use Shell oil and Mobil 1 on request.
Be careful with the free oil changes too.
There is serects to making $$$ on them like many crooked quick lube centers out there. They remove the oil filter, clean it well, and re-install it. Some even go as far insert machine screw to open up the anti drain back and flush the filter out a bit with solvents. But most will just wipe them with an armorall soaked rag to give it that shiny gloss new look if they don't have any paint chips or scratches on them.
So it costs them like $3 every time you want an oil change and thay makes HUGE proffits. Even if they do use OEM filters it only 1-2 bucks max for wholesale filters.
I used to buy filters at wholesale from Hiflofiltro, the supplier for Honda , Yamaha and many other OEM motorcycle filters. The Dealers charge as much as $15 per filter. Wholesale I was payin less then $3
yes, i am happy. this has given anyone without any knowledge in regards to oil choices to make an informed desicion. that is the whole idea behind a message board...
needless to say i still think that both of us are right and that our opinions that we DON'T share are both with merrit.
its been heated...
both of us think the other is still suffering the loss of nearly half a brain,
and its been entertaining...
needless to say i still think that both of us are right and that our opinions that we DON'T share are both with merrit.
its been heated...
both of us think the other is still suffering the loss of nearly half a brain,
and its been entertaining...
I'm no mechanic, but I would switch to a synthetic blend first if I were you. That will probably do the job of "engine flush" w/o putting other nasty chemicals in your engine. I have read that engine flushes are a waste of money. Run a blend, then swap. Your car will outlive you.Originally Posted by zyovkaWell, I am very tempted to switch to Amsoil or Mobil 1, too, on my older (1994, 170k) 4runner, but, Guys, can anybody explain, pls, what the difference is between 5W-30 and 10W-30... it's getting very confusing, when you go to those websites "find the oil that best fits your car", you answer the questions what type of vehicle you own, the year and so on, and, finally, you get the answer like 5W-30 or 10W-30... I guess the question is how do you know for sure what do you need: 5W or 10W....
We used Penzoil for years and it seems like the car runs good, but I wish I could do something good for my old and lovable Toyota 4runner.... any input would be very appriciated
Final thought: when a car has 170k miles on it, is it really worth changing to synthetic oil?
Well.... As long as we are all here and talking about oil changes.. Anyone got part numbers for non-genuine Toyota Filters?
Fram (these suck)
Amsol
Purolator
AC
What ever else is easily available??
Also.. Do you guys change the oil plug gasket? My Yaris is still new and I usually change the oil at 2000 - 2500 miles when new but for now, I haven't had it apart so I don't know what type of gasket it is. GM uses a rubber o-ring in an aluminum washer. Honda uses an aluminum crush washer. Pretty hard to get off the plug if you over-tightened the plug on the last oil change.
Fram (these suck)
Amsol
Purolator
AC
What ever else is easily available??
Also.. Do you guys change the oil plug gasket? My Yaris is still new and I usually change the oil at 2000 - 2500 miles when new but for now, I haven't had it apart so I don't know what type of gasket it is. GM uses a rubber o-ring in an aluminum washer. Honda uses an aluminum crush washer. Pretty hard to get off the plug if you over-tightened the plug on the last oil change.
i just did a quick search, here is what i found for oil filters
penzoil filter PZ39
mobil1 filter M1103
K & N filter HP1003
penzoil filter PZ39
mobil1 filter M1103
K & N filter HP1003
WRONG!Originally Posted by firefly1_0switching to synthetic oil on a new car is the g-hey.
wait four years, have a 100,000 Kms on it then make the switch unless you want to install new valve guides and seals.
you will be buring oil in no time if you switch.
http://www.mobil1.com/USA-English/Mo...ics/Myths.aspx
http://choosetoprosper.com/synthetic-oil-myths.html
http://www.castrol.com/castrol/gener...tentId=7007980
Firefly is getting smacked around like a redheaded stepchild on this thread...
What is "the g-hey" anyway?
I never thought I would see someone bash Synthetics. Thats like saying "Bricks Suck! Bricks can fall on your head and hurt you, use straw to build your house, nice soft straw." 😉
What is "the g-hey" anyway?
I never thought I would see someone bash Synthetics. Thats like saying "Bricks Suck! Bricks can fall on your head and hurt you, use straw to build your house, nice soft straw." 😉
He's probably just a victim of past "wive's tales" about synthetics that were born out of ignorance and fear of new technology that somehow seem to hang on through the ages despite the overwhelming data and engineering proof to the contrary.Originally Posted by nsmitchellFirefly is getting smacked around like a redheaded stepchild on this thread...
What is "the g-hey" anyway?
I never thought I would see someone bash Synthetics. Thats like saying "Bricks Suck! Bricks can fall on your head and hurt you, use straw to build your house, nice soft straw." 😉
i just prefer a longer wait. i never bashed them. that is all.
BTW
"the g-hey" = gay
BTW
"the g-hey" = gay
No problem.Originally Posted by firefly1_0i just prefer a longer wait. i never bashed them. that is all.
BTW
"the g-hey" = gay
But consider this analogy...
You're born and the doctor says to your parents; "I can give this kid a drug right now that will drastically decelerate the rate at which his body ages and wears out"
Do you think your parents would have said; "Naw, we'll wait till he's 40..."
i'll see your analogy and raise you one still on the fence...
...for now.
...for now.
Solid logic and a great post!🙇Originally Posted by 07WYarisRS
good regular conventional oil at $3 and filter $5 $ 20
Mobil 1 and conventional oil recommend 5000km oil changes that 20 oil changes over 3 years
Amsoil recommends I year oil changes or every 35,000 miles (what ever comes first)
Amsoil ($65 x 3) = $195
Mobil1 ($ 35 x 20) = $700
Regular conventional oil ($20 X20) = $400
Now just think how much money I have saved in my laser with 300,000km on the odometer. 7 oil changes.
That's $455 with Amsoil vs $2100 with Mobil 1
I don't know about you guys but I would rather save my $$$ then give it to big huge oil companies that rip us off fuel fuel prices as well.
I'd generally agree with this. But if you're running ANY oil a full 35K, You'd better have a few lab tests under your belt to prove that the filters and additive packages are holding up as designed based on your driving conditions and driving style.Originally Posted by 07WYarisRSBesides the power you gain and fuel you save you can save a LOT of $$$ using amsoil.
With Amsoil 2000 0w-30 and Amsoil filter it's good for 35,000 miles or one year
figure that out compared to how many regular oil changes you will do at 500mile intervals plus filters etc
you save $$$ using Amsoil in most cases unless you are running the cheapest conventional oils out there.
lets use my truck (99 chevy Xtreme) as an example.
Before I sold it, I put 100,000km on it in three years
5L of Amsoil X $9.70 plus filter at 16.45 =$65
Mobil 1 at $ 6 and purolator filter at $5 = $35
good regular conventional oil at $3 and filter $5 $ 20
Mobil 1 and conventional oil recommend 5000km oil changes that 20 oil changes over 3 years
Amsoil recommends I year oil changes or every 35,000 miles (what ever comes first)
Amsoil ($65 x 3) = $195
Mobil1 ($ 35 x 20) = $700
Regular conventional oil ($20 X20) = $400
Even if you are like me and change your Amsoil every 6 months that still only $390.
It's still cheaper then using mobil1 or most conventional oils and a group IV or V synthetic will protect your engine and free up more HP MUCH better then any conventional or even group III oil.
Now just think how much money I have saved in my laser with 300,000km on the odometer. 7 oil changes.
And after 300,000km the compression is still perfect, does not use more then a liter of oil between changes, no dreaded DSM lifter tic, and no dreaded auto trans O/D clutch slip. That would have been 60 oil changes using regular oil or Mobil 1. That's $455 with Amsoil vs $2100 with Mobil 1
I don't know about you guys but I would rather save my $$$ then give it to big huge oil companies that rip us off fuel fuel prices as well.
Good point and actually I have.
And not just Amsoil either. Over the past 10 years I've tested redline, Royalpurple, Maxima, Spectro,Yamalube, Hondaline, Motul and Mobil 1.
I've sent samples to US and canada to have lab testing done by independen labs there like Ana, blackstone and also Amsoil and Conklin. These places will test Any kind of oil and send the results back. It was much easier when i worked for a dealership but there are still independent labs out there that test for the general public.
All are good oil but Amsoil and redline products come back with the best results.
But if you read carefully I also said I change my oil every 6 months.
Why? Because I can, it's cheap insurance and it's still cheaper changing it every 6 months then using a cheaper oil and changing it every 5000km and i know I'm getting the best protection there is buy running a true synthetic
Here is one of my posts on the same topic I replied to earlier
QUOTE(doodoo @ Oct 25 2006, 10:59 AM)
I'd never leave oil in my car for 35000 miles no matter how good they say it is. Since when is mobil 1 refined dino juice? I thought it was the only major brand that was fully synthetic.
Well that's why I change my oil every 6 months. (see last paragraph of last post) I average about 30,000 to 35,000km a year. I change it once in the fall before the snow, once in the spring after the snow. That works out to about 15,000km per oil change. And even after 15,000km my oil is still looks great. It does not turn black like mineral based oils do.
I changed my oil in the Yaris back in June and it still looks new, I'll be changing it this weekend or next and it will stay in there until April or so. This works out great because I never need to change my oil in the cold or snow
Mobil 1 has been Hydrocracked mineral oil since back in the the days of the tri-synthetic (msds sheets are available)
but it is a full synthetic (sort of) just like Castrol Syntec.
Like Mobil 1 Syntec is a Group III synthetic. Castrol started this trend that most all synthetic oil manufacturers have switched to. What that means is that it is a highly refined Petroleum (dino-oil) is it's base stock. This happened several years ago and Mobil took them to court claiming Castrol couldn't call it a synthetic. Mobil said a synthetic is something man made in a lab to certain specs that can't be found in nature. Castrol said their process, called hydrocracking, was so good at refining the oil that it no longer resembled what is found in nature therefore it's a synthetic. The ruling was in Castrol's favor. Since then, pretty much ALL synthetics oils have switched over to the process, including Mobil 1, because it is cheaper to use this base stock rather than the traditional PAO base. Amsoil's XL-7500 line is a Group III oil but with much higher poa base stocks as mobil 1. Their regular line and Series 2000 line is still a PAO base group IV, or poloyolester Group V oil. Redline doesn't use this process either, and unless Royal Purple has changed in recent years, only their Racing Oils are a full PAO Group IV synthetic, most of the lines found on the shelf are a blend.
There still are questions on if this Group III synthetic is as good as the Group IVs. Since it's been a few years now, some results are coming back that the Group IIIs are not lasting as long as the Group IVs and some manufacturers that require synthetics in their products are looking into now saying it has to be a Group IV synthetic. This is because the Group IIIs still suffer the breakdown drawbacks that a petrolium does, once the additives get worn down. This has especially been noticed in Gear Lubes using a Group III oil.
BTW oil companies like Amsoil, Redline, Royal purple etc still buy their POA and Ester base stocks from companies like Exxon/Mobil.
FWIW we have a bypass system on several machines including daily driven trucks and our tractor. Lab results show after 100,000 km the oil is still perfect. With no mineral by products to oxidize and break down the oil maintains its viscocity and stability.
Now I no longer need to send in lab results.
I know for a FACT this oil will last well over 100,000km with a bypass system or just changing filters and with that in mind I have no problem leaving the oil in my car or truck for 6 months at a time.
Something that is truely amazing is the bypass systems ability to remove soot and particals so small the oil looks new after 100,000 km. What colors the oil and make it look black are the particles so small they pass through standard filters. Amsoils BP ilter will remove particles less then 1 micron and that removes that black color from the oil. So it always look new.
Thier are many truck lines that Use these products for 100,000-500,000 miles and after millions of miles they are still running like new. Just think how much Money they save in the long run.
----------------------------------------------------------------------------------------
Hey if people don't want to use Amsoil or one of the other top group IV-V oil like redline or royal purple...FINE, no problem.
I don't sell any of these products so there is no loss or gain to me.
But as a mechanic I want the best for my customers because I know a happy customer is a return customer.
I have a better reputation because my engines are strong, and LAST and don't break down
when needed the most. If my customers start getting DNF because of engine failures they are going to find a different engine builder. Ans using these products can give an engine that slight edge on the competition.
The same goes for everyone here...
I think the Yaris is a great little car and MOST buy them because they are cheap, fairly durable and good on fuel. I'm just telling people how they can preserve that, get better durability, performance, mileage and still save $$$.
And I understand that's not for everyone...
And not just Amsoil either. Over the past 10 years I've tested redline, Royalpurple, Maxima, Spectro,Yamalube, Hondaline, Motul and Mobil 1.
I've sent samples to US and canada to have lab testing done by independen labs there like Ana, blackstone and also Amsoil and Conklin. These places will test Any kind of oil and send the results back. It was much easier when i worked for a dealership but there are still independent labs out there that test for the general public.
All are good oil but Amsoil and redline products come back with the best results.
But if you read carefully I also said I change my oil every 6 months.
Why? Because I can, it's cheap insurance and it's still cheaper changing it every 6 months then using a cheaper oil and changing it every 5000km and i know I'm getting the best protection there is buy running a true synthetic
Here is one of my posts on the same topic I replied to earlier
QUOTE(doodoo @ Oct 25 2006, 10:59 AM)
I'd never leave oil in my car for 35000 miles no matter how good they say it is. Since when is mobil 1 refined dino juice? I thought it was the only major brand that was fully synthetic.
Well that's why I change my oil every 6 months. (see last paragraph of last post) I average about 30,000 to 35,000km a year. I change it once in the fall before the snow, once in the spring after the snow. That works out to about 15,000km per oil change. And even after 15,000km my oil is still looks great. It does not turn black like mineral based oils do.
I changed my oil in the Yaris back in June and it still looks new, I'll be changing it this weekend or next and it will stay in there until April or so. This works out great because I never need to change my oil in the cold or snow
Mobil 1 has been Hydrocracked mineral oil since back in the the days of the tri-synthetic (msds sheets are available)
but it is a full synthetic (sort of) just like Castrol Syntec.
Like Mobil 1 Syntec is a Group III synthetic. Castrol started this trend that most all synthetic oil manufacturers have switched to. What that means is that it is a highly refined Petroleum (dino-oil) is it's base stock. This happened several years ago and Mobil took them to court claiming Castrol couldn't call it a synthetic. Mobil said a synthetic is something man made in a lab to certain specs that can't be found in nature. Castrol said their process, called hydrocracking, was so good at refining the oil that it no longer resembled what is found in nature therefore it's a synthetic. The ruling was in Castrol's favor. Since then, pretty much ALL synthetics oils have switched over to the process, including Mobil 1, because it is cheaper to use this base stock rather than the traditional PAO base. Amsoil's XL-7500 line is a Group III oil but with much higher poa base stocks as mobil 1. Their regular line and Series 2000 line is still a PAO base group IV, or poloyolester Group V oil. Redline doesn't use this process either, and unless Royal Purple has changed in recent years, only their Racing Oils are a full PAO Group IV synthetic, most of the lines found on the shelf are a blend.
There still are questions on if this Group III synthetic is as good as the Group IVs. Since it's been a few years now, some results are coming back that the Group IIIs are not lasting as long as the Group IVs and some manufacturers that require synthetics in their products are looking into now saying it has to be a Group IV synthetic. This is because the Group IIIs still suffer the breakdown drawbacks that a petrolium does, once the additives get worn down. This has especially been noticed in Gear Lubes using a Group III oil.
BTW oil companies like Amsoil, Redline, Royal purple etc still buy their POA and Ester base stocks from companies like Exxon/Mobil.
FWIW we have a bypass system on several machines including daily driven trucks and our tractor. Lab results show after 100,000 km the oil is still perfect. With no mineral by products to oxidize and break down the oil maintains its viscocity and stability.
Now I no longer need to send in lab results.
I know for a FACT this oil will last well over 100,000km with a bypass system or just changing filters and with that in mind I have no problem leaving the oil in my car or truck for 6 months at a time.
Something that is truely amazing is the bypass systems ability to remove soot and particals so small the oil looks new after 100,000 km. What colors the oil and make it look black are the particles so small they pass through standard filters. Amsoils BP ilter will remove particles less then 1 micron and that removes that black color from the oil. So it always look new.
Thier are many truck lines that Use these products for 100,000-500,000 miles and after millions of miles they are still running like new. Just think how much Money they save in the long run.
----------------------------------------------------------------------------------------
Hey if people don't want to use Amsoil or one of the other top group IV-V oil like redline or royal purple...FINE, no problem.
I don't sell any of these products so there is no loss or gain to me.
But as a mechanic I want the best for my customers because I know a happy customer is a return customer.
I have a better reputation because my engines are strong, and LAST and don't break down
when needed the most. If my customers start getting DNF because of engine failures they are going to find a different engine builder. Ans using these products can give an engine that slight edge on the competition.
The same goes for everyone here...
I think the Yaris is a great little car and MOST buy them because they are cheap, fairly durable and good on fuel. I'm just telling people how they can preserve that, get better durability, performance, mileage and still save $$$.
And I understand that's not for everyone...
Excellent post 07WYarisRS
👏 👏 👏
I totally agree.... I would change at 6months interval regardless of how good the oil is. During the operation of the engine, fuel, water vapour, dirt, dust and other contaminants get caught or mix in with the engine oil. Many of these contaminants are not necessarily removed by the oil filter, like petrol, water vapour and broken down oil modelcules.
I wouldn't want engine oil floating with these contaminants for another 6 months in my engine.
Anyways, doesn't really matter if your gonna sell up after 4years or so anyway...
Happy motoring....
👏 👏 👏
I totally agree.... I would change at 6months interval regardless of how good the oil is. During the operation of the engine, fuel, water vapour, dirt, dust and other contaminants get caught or mix in with the engine oil. Many of these contaminants are not necessarily removed by the oil filter, like petrol, water vapour and broken down oil modelcules.
I wouldn't want engine oil floating with these contaminants for another 6 months in my engine.
Anyways, doesn't really matter if your gonna sell up after 4years or so anyway...
Happy motoring....
A very infomative thread. I have learned more then I ever wanted to know about oil. But seeing as I am about to switch to synthetic it has been quite helpful. I just have 2 quick questions. I have a 2007 Yaris HB with @ 8000 miles on it. I have had it into the dealer for 1 oil change. Looking at going with Amsoil 5W30. Would I realize any benefit if I flushed the system prior to the switch? And some recommedations on oil filters would be helpful (not a question but still counts as one) 🤷
With such little mileage I will be honest and say...you probably don't need an engine flush. What little deposits in there is not likely enough to clog up an oil filter, most will likely just settle in the sump pan (oil pan)Originally Posted by BefuddledA very infomative thread. I have learned more then I ever wanted to know about oil. But seeing as I am about to switch to synthetic it has been quite helpful. I just have 2 quick questions. I have a 2007 Yaris HB with @ 8000 miles on it. I have had it into the dealer for 1 oil change. Looking at going with Amsoil 5W30. Would I realize any benefit if I flushed the system prior to the switch? And some recommedations on oil filters would be helpful (not a question but still counts as one) 🤷
It's won't hurt anything to do it, but with only 8000miles I would not be worried about it.
Personally I use WIX (napa/uap) filters on engines that I change the oil every 6 months
Amsoil filters on engines that get oilchanges once a year or on bypass systems.
ThanksOriginally Posted by americanvitzI used to work at a Toyota dealership and I think the mechanics there have no clue on the different oils. Personally I use Royal Purple in my Yaris and have noticed a great increase in smoothness and gas mileage. I asked one of the mechanics what kind of oil is the best and his reply was Mobil 1. He said that Mobil 1 was the only oil made of fully synthetics and no mineral oil. I used to run Mobil 1 and did not see any kind of dramatic changes like I see with Royal Purple. Another mechanic also said that Amsoil is not worth the money that it all is just a marketing ploy but I am here to tell you that the facts don't lie and personally I think the Toyota Mechanics have not done their homework on oils. They just go with what ever is in the shop that is bought in bulk. So I guess what Im saying is dont ask the Toyota mechanics about oil, ask someone that has a clue about oil or has used the oil and had improvements. FYI as far as synthetics go, when I was in the Air Force I had to analyze the oil in the aircraft and what kind of oil does the military trust? you guest it SYNTHETICS. and they showed almost no wear!!!!👍
Link to a thread or page that is not in the archive This Man here knows his stuff and has done his homework.
As for the Toyota mechanics
Dealerships will always recommend short oil change intervals.
Dealerships will also recommend they do it. Some will even go as far to say that if you don't have the dealer change the oil it will void the warranty. Let me just say this.
NO dealership can deny your warranty if you decide to do your own maintenance.
The maintenance oil line in the owner’s manual is there for a reason along with a schedule when it should be done. Providing you keep the receipts for parts and a record of when it was done, you will not void any warranty. (Except on aftermarket parts installed)
So why do dealers recommend they change the oil so much?
Why do so many dealers not recommend synthetic?
Let’s face it... It costs a lot to run a shop or a large business like a car dealership. You have utilities, shipping, insurance, employee wages, stock/inventory, shop supplies, office supplies, tools, and advertising etc every month to pay for and still make a profit to be successful.
They do this with high shop rates (usually $75-$100 p/h) and fluid changes...
Dealerships buy regular dino oil in large bulk volumes and depending on where they get it they get it for below wholesale usually less then $1L (maybe not now that oil prices are so high though but it's not over $2) Most Canadian dealers buy oil from Shell or Esso. They also get oil filters direct from the mfg at prices below wholesale. (Usually $1-$2 each)
Now most dealerships charge about $25-$30 per oil change. My local Toyota dealer charges $29.95.
Think about that.
That's like $6 per liter they charge
That's about $5 worth of oil and filters and $20 to $25 profit off every oil change.
They make over $1000 per drum of oil. About 46 oil changes.
The more oil changes they can do the better. Most will go though at least one drum a week that's over $4000
Some big dealerships can go through 55 gallon every two days. YEAH that a lot of $$$
Now synthetic in bulk is a lot more money sometimes 3X the cheap stuff and therefore not as big of profits so they tend to push the cheap stuff and toss out a few myths about synthetics to keep you buyin the cheap stuff.
However Toyota does deal directly with mobil And most do offer Mobil1 so if they do push a synthetic it's going to be mobil1. Dealerships will charge you extra for the synthetic.
I know my small town Toyota dealer does not sell a car everyday, sometimes they will go 2-3 days with no sales but they always have the shop booked up for oil changes, transmission fluid changes, coolant flushes, tire rotations and the very basic maintenance usually all day long everyday. And just like a quick lube center that make great $$$ of simple fluid changes.
I'll be honest with ya. I could do 95% of my reapirs and maintenace but what about the small town dealership?
Even though I could do it I still take my cars in once in a while for simple things like tire rotations, brake inspections, etc.
I do this because it helps the dealership and I know they apperciate my buiness. The big city dealerships can all kiss my ass though LOL
They often charge even more then the little guys just out of greed.
Oh one more thing
What about the warranty?
The dealership is going to want to see receipts for oil changes should you have an internal engine problem. (very rare but it happens)
If you are like me and drive the wheels off you car, 8000K oil changes seem like a monthly thing.
What I do is every 8000km I go buy 5 L of oil and a filter, keep the receipt, copy it and return the oil and filter to the store.
I run my Amsoil for 6 months and if I ever have a problem I have proof I have changed my oil every 8000km just to keep Toyota happy.
What about the warranty?
The dealership is going to want to see receipts for oil changes should you have an internal engine problem. (very rare but it happens)
If you are like me and drive the wheels off you car, 8000K oil changes seem like a monthly thing.
What I do is every 8000km I go buy 5 L of oil and a filter, keep the receipt, copy it and return the oil and filter to the store.
I run my Amsoil for 6 months and if I ever have a problem I have proof I have changed my oil every 8000km just to keep Toyota happy.