yeah ill call you up if can make em or not cause right nows i dont know
Any good with electrical?
150 posts · 26,711 views · page 3 of 3
Replies continued
I thought I would post here before going to the "DIY section"
So me and Gwasabi tried to install power windows. we got it all wired up BUT couldnt find a power source to tap to that wouldnt blow a fuse! I tapped it to pretty much every wire on the steering column and where we thought might work. But after blowing 2 fuses and 5 hours later we thought we better stop and find out.
So anyone know how we can do this? where to tap or get our power source from?
So me and Gwasabi tried to install power windows. we got it all wired up BUT couldnt find a power source to tap to that wouldnt blow a fuse! I tapped it to pretty much every wire on the steering column and where we thought might work. But after blowing 2 fuses and 5 hours later we thought we better stop and find out.
So anyone know how we can do this? where to tap or get our power source from?
theres the big fat black wire on the fuse block thats constant 12 volts or you can tap it into the the switch wire should be fine
where is the fuse block? Is it behind the lower glove box thing where the tach wire is?
yes sir sorry my bad i never answer your call i was the kine at one grad party and never hear my phone i was out in north shore side
ok cool, I will try and finish tom'w. my gf is totally grossed out by my no door panel and gutted looking car... nah nah dont worry, just when we blew the first fuse, we had no idea why my tach and radio wasnt working. then found the blown fuse.
I took pics of me, Gwasabi, and Haku installing it. who wants to see? hahahaha funny stuff.
I took pics of me, Gwasabi, and Haku installing it. who wants to see? hahahaha funny stuff.
Ok well I took a quick picture of what I think the fuse block is, and looked for fat black wire. and this looked like the fattest.
Picture not included in this copy
Picture not included in this copy
its the one to the left of it
This?!
Picture not included in this copy
Wow I didnt even know that HUGE thing was a wire. haha
Picture not included in this copy
Wow I didnt even know that HUGE thing was a wire. haha
yeah thats a constant 12volt wire
whoa sweet. Oh! also is it ok to tap the illumination wire to the red constant? just like we did with my tach? so the back light is always on.
edit: how would be the best way to tap that big wire? cut some rubber off and just twist the wire around it and tape it off?
edit: how would be the best way to tap that big wire? cut some rubber off and just twist the wire around it and tape it off?
yup or you can find the alarm wires and tap into the red wire for the alarm thats also a 12volt constant that comes of the biggest harness on the alarm for the illumination wire i would tap it into the yellow wire off the alarm thats on the pack of wires that are all like stuck together so it turns off with the key
Ok! ill give it a shot tom'w and will put my wheels on my car! will report back later tom'w with the good or bad news. Dude thanks again devin.
no problem let me know when u get the alarm and stuff
Is that 12 constant always on? I was trying to tap into a source that only turned on when the car was on but I guess it doesn't matter
the big black wire yes is 12volts constant theres another wire that is ignition only when the key is turned on which is the one that he uses for the tach light
Ok from what I can tell on the manual it says the power gos to ignition and the illumination switch goes to headlight or something. I think he needs to take the two wires apart. I think its blowing the fuse cause we have both the illumination switch and power wire spliced together.
nah shouldnt not unless thats the main power it needs to move the windows
yups it is the main power.
oh ok if its the main power you need constant 12 volts so hook em to the big black wire or the red wire off the alarm and the illumination is off the yellow wire coming off the alarm
Ok when I tap to the big black wire it instantly blows the fuse, I did I twice just to make sure. Ill try tap it to the alarm red off the largest harness and the yellow off the one next to it thats all stuck together.
here we go!
here we go!
Ok hooked it up to the yellow and red wire of the alarm. and it blew the tach/radio fuse, but the power window was working, even with the car off it worked. then it stopped. Im not sure if I blew two fuses, but i replaced the tach/radio fuse and tried again.
It blew the fuse again, so i took the illumination tap off the yellow wire and replaced the fuse, and tried. It didnt blow the fuse but it still wont work. No power. But im not sure if I blew two fuses, everything seems to work.
edit: Pulled and checked all the fuses in the inside and all good. quite confused
It blew the fuse again, so i took the illumination tap off the yellow wire and replaced the fuse, and tried. It didnt blow the fuse but it still wont work. No power. But im not sure if I blew two fuses, everything seems to work.
edit: Pulled and checked all the fuses in the inside and all good. quite confused
ok so one of two things either it draws to much current or something is grounding out in the unit itself
I was thinking. Could I tap it to a 25 fuse and put it in the empty power window slot?
try hool em up to the battery straight
ok ill try that now.
Ok total newb question, the wire wont reach to the engine bay, I dont know what gauge wire it is. could I use a smaller or bigger wire? or does it have to be the same gauge?
Ok total newb question, the wire wont reach to the engine bay, I dont know what gauge wire it is. could I use a smaller or bigger wire? or does it have to be the same gauge?
Ok tired to hook it up straight to the battery. and it blows the fuse. haha
can be smaller just to test it out
Ok yeah it blew the fuse that is connected to the red wire.
maybe the illumination wire, you gotta run a fuse through it too..... not too sure though
Buy a cheap multimeter and check for ground fault with the wire and the alarm. If there is a ground fault, the alarm is no good.
😆
wow not even close to what we are trying to figure out
wow not even close to what we are trying to figure out
^ I have a multi meter but yeah, not trying to work my alarm.
ok another thing i was thinking about. maybe we wired it wrong. i will try draw out in detail what we did.
ok another thing i was thinking about. maybe we wired it wrong. i will try draw out in detail what we did.
Ok my drawing failed. here are pictures
the guide:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
the guide:
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Ok I'm going to try hook up a relay. See if it will still blow fuses.
Which and where is the ignition wire? Haha
Which and where is the ignition wire? Haha
try tape up the metal parts the spark might be jumping
hey where is good places to tap my relay?
I bought a SPST relay. I was planning on tapping the "30" straight to the battery, "85" of course grounded, "87" to the power window red wire, and "86" to the Ignition wire (maybe tap the the yellow wire on alarm).
How does that sound devin?
I bought a SPST relay. I was planning on tapping the "30" straight to the battery, "85" of course grounded, "87" to the power window red wire, and "86" to the Ignition wire (maybe tap the the yellow wire on alarm).
How does that sound devin?
that sounds good
Omg yes. Finally works. Now just need to do the passenger side and clean up the wires because it's a mess. I will pick up the viper alarm tom'w. And I'll ask them about power locks also.
post some pics!
haha i will post some tom'w when i finish working on them.
hey devin I went down and asked about the power lock kit and showed them the ones I have. They told me that I could use the ones I have and thats the power lock kit and keyless kit is separate. They just said that once I install the lock that just connect the brown and purple wire to the viper.
So whenever your free again, Im going to pick up the new viper alarm tom'w, and should be finished with my power windows. Im not sure about the Clifford wires, but I will try and clean up the power window wires (It a mess!)
hey devin I went down and asked about the power lock kit and showed them the ones I have. They told me that I could use the ones I have and thats the power lock kit and keyless kit is separate. They just said that once I install the lock that just connect the brown and purple wire to the viper.
So whenever your free again, Im going to pick up the new viper alarm tom'w, and should be finished with my power windows. Im not sure about the Clifford wires, but I will try and clean up the power window wires (It a mess!)
oh ok sounds good
Ok picked up the Viper 5002. And will finish putting the power windows on today. Ill also take some pics.
Oh devin, I forgot to save your number, and lost it in my phone. But let me know when you can come over again.
Oh devin, I forgot to save your number, and lost it in my phone. But let me know when you can come over again.
Here is the pic I promised. haha
Picture not included in this copy
Picture not included in this copy
Nicee. Do you have to cut a section in your door panel now for the switches?
yup i was going to do that last night, but some crazy guy who lives across the street had a knife or somthing and the cops said to stay in my house...
Wow thats some crazy shit man
tell me about it, crazy new people.
Oh What guage wire and fuse should I use to connect my power straight to the battery? Right now im just using a thin wire just to test it, but people said to get thicker wire and stick a fuse over there.
should be the same size as the wire coming off the unit