Yarisworld Archive

Replacing stock deck - photo tutorial

40 posts · 41,579 views

gravylegsOriginal postToronto · May 26, 2006#1
Hi people, while I was replacing my deck / door speakers I snapped a few photos with my phone. Might be useful to the more timid folks out there who don't like reefing on panels until you find the right one.

getting the stock deck out is as easy as 1-2-3.

1. Start with the center panel trims on the left and right of the stack. Pull at the bottom of each one, and follow it all the way up. Once you have them detached, you can either lay them on the dash, or disconnect them and set them aside. I let them dangle because I am lazy.
Picture not included in this copy
Picture not included in this copy
2. Starting at the top of the trim on the speedometer window, pull the trim so it detaches, and keep pulling evenly on both sides until the who thing comes off to the environmental controls. It is two pieces, but is easier to remove as one piece.
Picture not included in this copy
3. There are 4 easily accessible screws holding the deck in, just unscrew 'em and yank the deck out!
Picture not included in this copy

Putting a new stock deck in is NOT as easy as 1-2-3! I bought an echo mounting kit as mentioned by someone else on the board, and while the kit was useful to provide something of a "face", it wasn't very useful to actually mount a stereo. Here is what I ended up having to do.

1. Detach mounting brackets from the stock deck.
2. Widen holes in side of deck if required. I did this with a drill, but more out of frustration...
3. Mount stock brackets onto new deck.
4. Hook toyota wiring harness on onto new deck's wiring harness. (Saves you having to chop up the wires in your dash...ask if you dont know what this is about)
5. Plug everything in and test stereo out to ensure connections are good.
6. Mount the deck with the 4 screws.
7. NOW....use the toyota echo mounting kit....all I could do was to chop off the extra tabs, and then place it in "around" the new deck. It fits in there snugly.
8. replace all the dash parts, and you have a new stock deck that works! The only drawback is that the faceplate of the mounting kit does not COMPLETELY fill the hole in the dash. It is pretty close, and doesn't look TOO bad....but I will for sure be buying the proper mounting kit once it is available.

Hope this helps someone. Pulling off doors tutorial with pics coming soon.

Gravylegs.

4 attachments not included in this copy

Replies 39

DylanbyGTA · May 26, 2006#2
You left out the finale. Where's the money shot? We don't get to see the end result 😁
gravylegsThread starterToronto · May 26, 2006#3
lol...oh yeah...money shot coming soon.
IdjiitHolly Springs, NC · May 26, 2006#4
Thanks for sharing, man.
Leenis24Northern Vermont · May 26, 2006#5
thank you for this, i was wondering how to go about pulling things off. Sweet post, like to see those other pics as well.
eight_headsLA, USA · May 31, 2006#6
yeah, i'm wondering how well the echo trim fits in.... let's see 🤷
KitelessUnion City, CA - U.S.A. · Aug 4, 2006#7
Hey man. Great post. I was hoping to see what things looked like with the stock stereo pulled out. After what you said about the Echo dash kit, that makes me all the more wanting to wait for the proper Yaris dash kit. Aparewntly Metra keeps saying "2 more weeks". I dont understand what is taking so long. ;p
twixtsyracuse, ny · Aug 4, 2006#8
i find installing the left side flasher rubber thinger is a pain because if it is a little outa wack the flasher button will stick.
ViolinNew Jersey · Aug 4, 2006#9
Thanks. That helps a lot.

C'mon Metra!
johnnyfiveMilwaukee WI · Aug 5, 2006#10
wow, that is quite a bit different than the sedan...same basics though..
SmellyTofuSydney · Aug 8, 2006#11
Props for this thread. Very easy to follow.
KatanaUnder the hood! · Aug 14, 2006#12
Gravylegs do I have your permission to post your tutorial to the Greek forum dedicated to Yaris???

Check it out www.yarisclub.gr

EDIT:Do you have any tutorial on how to change the speakers?
iloveyarisRScanada · Aug 14, 2006#13
wow.............nice........thx for sharing
LinksealVancouver, BC · Aug 14, 2006#14
Thx for sharing the info and Pics...now I have sth to follow when I am gonna do mine...

But if anyone could share the pics and instruction on how to take out and front and rear door panels to change the speakers...Plz🙇
gravylegsThread starterToronto · Aug 14, 2006#15
Sure, go nuts with the tutorial! Glad people actually find it useful. I actually just replaced the speakers this weekend, and tho I did take pictures I just need to throw them up here. I'll do that in the next day or so.
KatanaUnder the hood! · Aug 15, 2006#16
Tnx for your approuval.

I will mention your name to the greek forum.

Please post the speakers tutorial too.
ViolinNew Jersey · Sep 2, 2006#17
I hope I'm not stepping on your thread here, but I just installed mine and figured it made sense to put these here rather than having two threads.


These sure help. I have them as pdf files. If anyone can host them, I'll email them to you.

Picture not included in this copy
Picture not included in this copy
(don't remove the gauges - step 5)
Picture not included in this copy
(don't remove a/c control panel)




Before you start, disconnect the battery ground.


Remove left side trim (start and bottom and work up):
Picture not included in this copy


Same for the right:
Picture not included in this copy


Unplug both and set aside:
Picture not included in this copy


Remove instrument gauge trim:
Picture not included in this copy


This is what the clips look like:
Picture not included in this copy


Remove the ventilation trim (start at top):
Picture not included in this copy


Ready to remove stock radio:
Picture not included in this copy


Remove 4 screws, pull out stock radio and unplug:
Picture not included in this copy


This connector will not be used (for iPod):
Picture not included in this copy


I used the metra smart harness (no soldering):
Picture not included in this copy


Put new head unit in metra kit:
Picture not included in this copy


Plug in new head unit (antenna too):
Picture not included in this copy


Install with 4 screws:
Picture not included in this copy


Replace gauge and ventilation trim:
Picture not included in this copy


Plug in and reinstall left and right trim:
Picture not included in this copy


Install head unit face plate:
Picture not included in this copy


Reattach battery ground and enjoy!:
Picture not included in this copy
KatanaUnder the hood! · Sep 2, 2006#18
Nice info there Violin.

Can someone post a tutorial on how to remove the OEM speakers?
YamilRSan Diego, CA · Sep 2, 2006#19
Did you ended up using #99-8216 for the Dash kit and #70-1761 for the harness?
ViolinNew Jersey · Sep 2, 2006#20
Yes to the dash kit.

For the harness I went to Circuit City and got the Metra 'Smart Harness" #80-1761 and the one specific to the JVC deck. That way I didn't have to do any soldering. It did cost more though.

http://www.circuitcity.com/ssm/Metra...oductDetail.do
YamilRSan Diego, CA · Sep 3, 2006#21
Originally Posted by Violin
Yes to the dash kit.

For the harness I went to Circuit City and got the Metra 'Smart Harness" #80-1761 and the one specific to the JVC deck. That way I didn't have to do any soldering. It did cost more though.

http://www.circuitcity.com/ssm/Metra...oductDetail.do
If yo dont mind I will be doing the same set up you got, looks very clean but why do I need 2 harnesess? This will be my first radio install since I bought the car without the stereo 🤷
ViolinNew Jersey · Sep 3, 2006#22
The #70-1761 requires you to solder all the wires to the other half of the harness that comes with the new head unit.

The Smart Harness #80-1761 terminates in a universal adapter that snaps into an adapter on the other end of the harness metra makes specifically for each manufacturer. It does cost more but saves an hour or so of soldering.
SimmZQuebec · Sep 3, 2006#23
Wow! Great write-up sir! 👍

I have to admit the installation is VERY easy into the Yaris!! It take around one hour to replace my deck into my Cavalier with my friend who own a professionnal audio shop. We have to remove THE ENTIRE DASH to remove the deck! I'm not kidding, see a proof above! It's not my car, I found this pictures into a write-up on the web! LOL 😆

Picture not included in this copy
ebowers83Baltimore, MD · Sep 14, 2006#24
Wow thats a great tutorial.... but my dash looks totally different than yours.... if you look at the picture, the panel only leaves a slit open for the cd to go in, and it extends to cover the vents. Theres no hole like yours! So how would I install mine? And what about the aux port that I use for my ipod?

Picture not included in this copy
ViolinNew Jersey · Sep 14, 2006#25
That's a sedan. Mine's a liftback.
AykaRochester, NY · Sep 29, 2006#26
Does anyone know any other Metra Product numbers that would fit a Hatchback w/ COnvience Package? Im having trouble finding #99-8216 in my local area.

Is there a Large Chain that may carry this? Will #99-8101 or #99-8202 work for what I need? (Single DIN Unit)
ViolinNew Jersey · Sep 29, 2006#27
If you can wait a couple of weeks, I can let you have mine super cheap. I'm making some changes and need to go to a double DIN set up.
yuiedieCA · Oct 8, 2006#28
haha, awesome, I also ordered a yaris without stereo (only speakers) so this guide will come in handy. im a newb so one question, how do I remove the battery ground?
ViolinNew Jersey · Oct 8, 2006#29
10 mm socket wrench.
yuiedieCA · Oct 9, 2006#30
ok. i also have another question that prolly will make you laugh because its so newb but anyways, is there anyway i can just connect an ipod to the car speakers instead of having to get a head unit?
johnnyfiveMilwaukee WI · Oct 9, 2006#31
sure you could, but it will be super quiet, and may damage your i-pod :)

but if you really really wanted to, you could run the ipod to an amplifier, and then run the amplifier to the speakers ;)
yuiedieCA · Oct 10, 2006#32
hmm, of course i wouldnt want to damage the ipod haha. but just curious, would i have to buy any wiring/connectors?
Yaris-TJTijuana, Mexico · Nov 3, 2006#33
👍 great DYI!

Using the appropiate metra kit, and the right harness for your stereo, you can even say it's plug-n-play🎉
Yaris-TJTijuana, Mexico · Nov 3, 2006#34
[QUOTE=ebowers83]Wow thats a great tutorial.... but my dash looks totally different than yours.... if you look at the picture, the panel only leaves a slit open for the cd to go in, and it extends to cover the vents. Theres no hole like yours! So how would I install mine? And what about the aux port that I use for my ipod?

The only way I see you can do it...is to get a trim that looks like this one
Selling Price for Stock Unit with MP3

This will replace your stock, leaving space for an aftermarket one..

BTW mine is a sedan
eflb55MI, US · Dec 23, 2006#35
Has anyone removed the dash off the sedan to get to the stereo?
yarisugiハワイ · Nov 5, 2008#36
I'm new and this thread is old, but thank you Violin for the photos. They were very helpful.
skigilDallas, TX · Dec 24, 2008#37
+1
ozmddDFW, TX · Jan 1, 2009#38
OK, I saw the notation that one of the harness plugs was for Ipod. Is that pre-wired in the vehicle? I thought that harness had to be added to Yarii? Please clarify, as my new Scion HU has ipod capability and a corresponding plug in the back.
pj1989Brisbane · Jan 5, 2009#39
Cool thread that is all really helpful. Does anyone know if you can just wack any stereo in there though or does it have to be certain size/brand etc
bsg916Ga · Feb 6, 2012#40
I have the metra 99-8202 mounting kit but am a bit paranoid about which tabs to take off since the directions dont actually list the yaris. If someone could tell me which letters to remove or point me to which cars directions to follow for removing the tabs it would be greatly appreciated.

Brian