Yarisworld Archive

16's or 17's

54 posts · 17,754 views · page 1 of 2

riceboyOriginal postCAN · Apr 13, 2006#1
What does everyone think? At first I was thinking that 17's were my best bet,.. but after thinking about it some more I'm thinking that 16's might offer the better performance pkg, not to mention less chance for wheel damage from all those crappy toronto streets...

Replies 53

DJ_SpaRkyGroveland, FL (Near Orlando) · Apr 13, 2006#2
I'll be getting or using my current 17"s
IdjiitHolly Springs, NC · Apr 13, 2006#3
Given the two choices, I'd go with 16 since the car is so low-powered. Personally, I'll be going with 15s.
why?harnett county NC · Apr 13, 2006#4
It depends on what you are going for. For maximum performance the bigger the wheels the better.

For looks, the same applies.

If something else, then you can go with smaller wheels.

I'm prolly going with 14s.
bdiuVancouver · Apr 13, 2006#5
17" no doubt

👍
FCP91Boring Vancouver · Apr 13, 2006#6
18S!!!! Yea!
birdydenton,tx · Apr 13, 2006#7
22's ya'll (omg omg omg omg)

jk
jcoveBrampton, Ontario, Canada · Apr 13, 2006#8
Originally Posted by riceboy
What does everyone think? At first I was thinking that 17's were my best bet,.. but after thinking about it some more I'm thinking that 16's might offer the better performance pkg, not to mention less chance for wheel damage from all those crappy toronto streets...
I'd like the 17's, but you make a good point about the streets here. LOL I want to put in the lowering springs first (wish I did it when I got the car) Then I'll worry about the wheels. I have something in the works for an exhaust. I didn't plan to do it until later this summer but something good has come along. 👍 I'll post more about it later, in another thread.
drell42Not here · Apr 13, 2006#9
for me its a 16x7
riceboyThread starterCAN · Apr 14, 2006#10
I'm pretty sure the 18s are out of the question running low pro 30 rubber bands isn't that appealing to me... that could mean bent rims, and really, really, really expensive tires... the more I look at the Yaris, the more I think that 17s would be the best fit... My major dilema is that I'm stuck in thinking that for the same price of a 17 in pkg, I could get some better quality wheels and tires pkg in 16.....
DJ_SpaRkyGroveland, FL (Near Orlando) · Apr 14, 2006#11
Originally Posted by birdy
22's ya'll (omg omg omg omg)

jk

LOL, I know some people are trying to put them on xBs but they can't find a tire small enough.
YarisHatchBlank · May 24, 2006#12
15's or 16's if you want performance, 17's if you want looks. Anything more than that, common its a yaris.😢
silverRSOttawa Ontario Canada · May 25, 2006#13
yup I'm going with the 16's
rickoGeorgian Triangle Ont. · May 25, 2006#14
I'm now thinking of just going to beefier skins on my 15's. Anybody know how wide you can go on the stock RS alloys? I know 195/55 x15 will work, but I was thinking maybe 205/50 x15???? I dunno if that will violate the law of diminishing returns.
CalidrifterChatsworth and Fontana · May 25, 2006#15
16" SSR meshies or 17" that I have on my 240
spacemanoeuvresBucks County, PA · May 25, 2006#16
I'm gonna get some cheapy 16" Rage Vigor wheels with 205/50/16 tires:

Picture not included in this copy

They'll look like stock wheels but a lil' bigger/wider which is what I'm going for...

Don't want to take too much attention away from the car itself 😁
silverRSOttawa Ontario Canada · May 25, 2006#17
yeah true, those that pattern is pretty sick, kinda what im looking for.
spacemanoeuvresBucks County, PA · May 25, 2006#18
Originally Posted by silverRS
yeah true, those that pattern is pretty sick, kinda what im looking for.
yep, I think they'll look pretty cool.

the 16X7 weighs 17.8 lbs which isn't much heavier than the stock 15" steel wheel.

not bad for $100-105 👍

be sure to post pics if you buy 'em
Leenis24Northern Vermont · Jun 3, 2006#19
Im going with 16x7 on 205/50 tires. Im going with the Flik Ftd (matt Titanium) wheels. They would look hot on Meteorite metalic color.
ROCKLAND TOYOTAROCKLAND COUNTY NY · Jun 3, 2006#20
I'LL BE going with the trd 18's and shelving the stock alloys for winter.....
YarisHatchBlank · Jun 3, 2006#21
I'm really happy to see yaris owners doing their cars right. Especially with wheels, wheels aren't a huge deal to me but when its done, bigger is never better. 👍

My hatch is supposed to come in the 18th, payments should work all i have to fear now is getting the exact insurance numbers. The estmates were good to go, but hopefully it wont change much with an actual vin. If it doesn't, say hello to a future black 5spd owner.👏
SophieSleepsMA · Jun 4, 2006#22
Originally Posted by why?
It depends on what you are going for. For maximum performance the bigger the wheels the better.

For looks, the same applies.

If something else, then you can go with smaller wheels.

I'm prolly going with 14s.
Yo man. I don't mean to pick on you.

But bigger isn't better for performance.

If the overall diameter of a wheel is say 20"
And you have 19" of it metal, and 1" tire...teh combination will weigh much more than one with say 15" of metal and 5" of tire.

Rotating mass kills performance.


However, you are right about thinner sidewalls being better for performance.
Having a stiff, thin sidewall makes a car much more responsive.

If I do end up getting a Yaris...I will be going with 18's.
I don't care about performance on a car with 100hp.
Why would anyone?
If I decide to play around, I will throw in some forged internals and boost it to high heaven. Screw this 140 hp stuff. That's kiddies play.
echo_hrsTop Gear Test Track · Jun 4, 2006#23
SophieSleeps, I think you need a good foot massage...
echo_hrsTop Gear Test Track · Jun 4, 2006#24
Originally Posted by ROCKLAND TOYOTA
I'LL BE going with the trd 18's and shelving the stock alloys for winter.....
Hey ROCKLAND, are you able to source the TRD F1 alloys for the Vitz in the 17 inch size? Toyota Canada has been parading a hatch around with a set, but have become like the CIA when it comes to getting a straight answer on how to get a set...

http://www.trdparts.jp/english/parts_wheel-tf1.html

Picture not included in this copy
Picture not included in this copy

18s would be way to harsh for my tastes...

Cheers
SophieSleepsMA · Jun 4, 2006#25
Originally Posted by echo_hrs
SophieSleeps, I think you need a good foot massage...
I think I need to find a girl with hot feet and give a good foot massage.
why?harnett county NC · Jun 4, 2006#26
Originally Posted by SophieSleeps
Yo man. I don't mean to pick on you.

But bigger isn't better for performance.

If the overall diameter of a wheel is say 20"
And you have 19" of it metal, and 1" tire...teh combination will weigh much more than one with say 15" of metal and 5" of tire.

Rotating mass kills performance.


However, you are right about thinner sidewalls being better for performance.
Having a stiff, thin sidewall makes a car much more responsive.

If I do end up getting a Yaris...I will be going with 18's.
I don't care about performance on a car with 100hp.
Why would anyone?
If I decide to play around, I will throw in some forged internals and boost it to high heaven. Screw this 140 hp stuff. That's kiddies play.
Dude, for handling, the bigger the better. For tires performance=handling.

As I said before, you really are an ass.
SophieSleepsMA · Jun 4, 2006#27
Originally Posted by why?
Dude, for handling, the bigger the better. For tires performance=handling.

As I said before, you really are an ass.
Tire size has nothing to do with rim size.
The dude's question was about wheel size, not tire size.



You can run a 305 on a 18 or a 305 on a 16. Either way, the contact patch on the tire is the same.

Width doesn't necessarily mean performance. The wider the tire, the slower you'll go but the better you will turn.

All I'm saying is that you shouldn't make a blanket statement like "bigger is always better".
How come race cars don't run big 26" wheels then?

-Ass
SmellyTofuSydney · Jun 5, 2006#28
I run 16" (as in the avtar) with 195/50R16 Advan A048.. that's harsh enough on imperfect roads I drive on.
SmellyTofuSydney · Jun 5, 2006#29
Originally Posted by echo_hrs
Hey ROCKLAND, are you able to source the TRD F1 alloys for the Vitz in the 17 inch size? Toyota Canada has been parading a hatch around with a set, but have become like the CIA when it comes to getting a straight answer on how to get a set...

http://www.trdparts.jp/english/parts_wheel-tf1.html

Picture not included in this copy
Picture not included in this copy

18s would be way to harsh for my tastes...

Cheers
Check the track and offset (TRD TF1 being +51) is correct for your vehicle. You will find variations between different countries and their choice of suspension setup.
jbrand2002uk1north east england · Jun 12, 2006#30
well i have a dec 05 yaris and i have 16's on and they are ok to get up to 17's though you might have to roll the arches or remove the inners to make them fit other you rick the tires rubbing on the arches and any bigger than 16's and the handling will suffer.😈
JaspherToronto, Ontario, Canada · Jun 12, 2006#31
I not sure if all Yaris are like this but the one's we have in Canada.. (which is imported from Japan) have rolled wheel arches already. If you havn't checked yours go out and have a look. This is a smart move by Toyota.
RonVancouver · Jun 12, 2006#32
i am running 16" TRD wheels, 195/50/16 in the front and 205/50/16 in the rear. +47 offset, TONS of clearance space between the tire and the strut bodies. With the extra width over the stock 14" steelies/wheel covers, it looks a bit more flush with the car and not tucked at all. I'll report back once i have the car lowered, but i dont anticpate any problems whatsoever.
Fat FelixxxSan Dimas, CA · Jun 12, 2006#33
Originally Posted by Ron
i am running 16" TRD wheels, 195/50/16 in the front and 205/50/16 in the rear. +47 offset, TONS of clearance space between the tire and the strut bodies. With the extra width over the stock 14" steelies/wheel covers, it looks a bit more flush with the car and not tucked at all. I'll report back once i have the car lowered, but i dont anticpate any problems whatsoever.
Running wider tires(or wheels or lower offset) in rear would further promote understeer in a car that is naturually prone to understeer.

Whle running a staggered look like that might look cool, it actually decreases performance. Running reverse of that (wider front wheel/tire or lower offset wheel) would make the car handle better because it would help the car handle more neutrally.

If high performance driving is not an issue, there would be no problems.
RonVancouver · Jun 12, 2006#34
high performance driving is NOT an issue; i will not be driving the yaris anywhere near its limits as it is simpily a day to day commuter car (i gave up my MR2 for this purpose).

the 10mm extra width between the rears and fronts is barely noticeable visually, so theoretically i guess it looks cool. the only reason i am running staggered is because i got a great deal on a barely used pair of 195/50/16 yokohamas, and tirerack had some 205/50/16 kuhmo's stupid cheap. 4 z-rated summer tires for under $200usd all installed and mounted up :D
TRD_YarisAustin, Texas · Jun 13, 2006#35
Originally Posted by why?
Dude, for handling, the bigger the better. For tires performance=handling.

As I said before, you really are an ass.

umm..no.. tire performance is a COMBINATION of lateral/longitudal grip as well as balancing sidewall stiffness between Ride Comfort and Responsive handling. If bigger wheels = better perormance, then why do people drag race with small, lightweight wheels?! stiff sidewalls SUCK for launching...so, obviously bigger doesn't always means better performance.

Pretty much, if you choose a wheel/tire combo that weighs more than stock, you will lose performance 99% of the time. If you can go bigger and reduce weight, then more props to you, but be prepared to drop 1/4 cost of your yaris for some forged Volks, iForged, HRE, etc.
Personally, i'll spend $95 each for 15x6.5 Falken Hanabis (11.13 pounds) w/ Falken Ziex 512 tires for $41 each... mounted/balanced/shipped from EDGERACING.com for less about $600...
hehe...i remember having 18" staggered wheels on my GS300..people thought it was lame that i didn't have 20s until they saw my timeslips or looked under the hood (2JZGTTE swap from JDM AE94 Supra).
If you feel it more important to look sporty than to be sporty, then that's your choice. but, please don't go around saying that bigger wheels = ALL AROUND better performance, because you are 99% wrong.

Lemme guess, very few of you actually circuit/club race and do your own tuning/modification?....thought so. going from Cast to Forged 15" wheels on my SCCA civic freed up 3whp (at 2600rpm) to 7+whp @ redline...
and for you that don't know the difference between cast and forged, then you shouldn't be buying aftermarket wheels to begin with


oh, and btw..going with much wider tires than stock will also hurt your gas mileage and cause your vehicle to pull to the side more when going over uneven surfaces (either from different roughness or topography). just be prepared to struggle more, and watch those potholes...hahaha
why?harnett county NC · Jun 13, 2006#36
Yawn.

Drag racing doesn't require handling. Drag racers don't turn at all.

It requires traction. The sidewalls of drag tires are built to warp so that traction is increased.

And most drag tires are rather large, if you haven't noticed.

I highly doubt many people will try to drag race a Yaris.

As for handling, the wider the contact patch and the stiffer the sidewall the better.
DJ_TrizzakVancouver, BC · Jun 13, 2006#37
I would go with 17's
DJ_TrizzakVancouver, BC · Jun 27, 2006#38
ya changed my mind - I'm getting 16's then maybe lower it after
RonVancouver · Jun 30, 2006#39
^ that's my exact same setup. 16", lowered. feel free to pop by sometime and have a closer look in person, seems like we're in the same neighbourhood :)
DJ_TrizzakVancouver, BC · Jun 30, 2006#40
^^ - dope!! - yah man I should check it out - you didn't come to the echo meet couple months ago? where in van you at - looks like you have the same color too LOL - Auto or Manutal? RS? LE? CE?
fnkngrvIn The Hotbox · Jun 30, 2006#41
Originally Posted by ROCKLAND TOYOTA
I'LL BE going with the trd 18's and shelving the stock alloys for winter.....
I have the 15s that come with the S and plan on putting them up for winter as well....I am working on getting 16" PKRs...
Picture not included in this copy
RonVancouver · Jul 1, 2006#42
Originally Posted by DJ_Trizzak
^^ - dope!! - yah man I should check it out - you didn't come to the echo meet couple months ago? where in van you at - looks like you have the same color too LOL - Auto or Manutal? RS? LE? CE?
no, i havent made it out to any echo meets. feel like i am betraying my mr2 club 😳

i have a 5 dr blazing blue auto, basic LE trim. im out of town til wednesday, but shoot me a pm and we can meet up. i LOVE the lowering springs and fatter tires, both for looks and for the increased handling capacity.
spacemanoeuvresBucks County, PA · Jul 8, 2006#43
Originally Posted by Leenis24
Im going with the Flik Ftd (matt Titanium) wheels.
Picture not included in this copy

nice!

these'll look sweet on blazing blue as well 😉
LafiroNYC · Jul 8, 2006#44
Ok, well my few questions.

Why hasn't anyone bought the 18 TRD's? Don't complain about the $1999~ pricetag. Just the reasons.

Also, doesn't it have to be 4 bolts, not five, as the picture of those greyish rims?

My last question, most important to me, since I have had my 07 Yaris Sedan, Pacific Blue for months now. What color rims should I get and what size, cause these 15inch steels are getting to me now, since summer is here.

Thanks!!!
wlfpckChicago · Jul 8, 2006#45
Originally Posted by why?
It depends on what you are going for. For maximum performance the bigger the wheels the better.

For looks, the same applies.

If something else, then you can go with smaller wheels.

I'm prolly going with 14s.
actually... u probably don't wanna go over 17's... cuz the bigger the wheel, the more power it requires to get it moving.
silverRSOttawa Ontario Canada · Jul 8, 2006#46
on the blue I would get Gunmetal or charcoal.....looks sweeeet on the blue
LafiroNYC · Jul 8, 2006#47
Originally Posted by silverRS
on the blue I would get Gunmetal or charcoal.....looks sweeeet on the blue

Alright, I was also told the same by a few others at my job. Alright, can any of you recommend any tire sizes, and rim sizes aswell please?

Thanks, again!
spacemanoeuvresBucks County, PA · Aug 1, 2006#48
Originally Posted by Leenis24
Im going with 16x7 on 205/50 tires. Im going with the Flik Ftd (matt Titanium) wheels. They would look hot on Meteorite metalic color.
JIC you haven't picked them up yet, there's a set of 17" on ebay: http://cgi.ebay.com/ebaymotors/17-FL...spagenameZWDVW

these woud look schweet
DARKYARISCrazyville, Canada · Oct 31, 2006#49
I went with the 17" Motegi and 205/40ZR 17 rubber...Still stock ride height.

Picture not included in this copy
pascalmontreal · Oct 31, 2006#50
I have 16 go see my garage